The MPC8308RDB Reference Manual states that no bits in the SPMODE
register are allowed to change while the enable (EN) bit is set.
This driver changes the character length bits (LEN) while the enable
(EN) bit is set. Clearing the EN bit while changing the LEN bits makes
the driver work correctly on MPC8308RDB.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
greth.c: In function ‘greth_recv’:
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’ [-Wformat]
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘unsigned int’ [-Wformat]
greth.c:541:6: warning: pointer targets in assignment differ in signedness [-Wpointer-sign]
greth.c: In function ‘greth_initialize’:
greth.c:623:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:655:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:684:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: u-boot-dm@lists.denx.de
Use the same IP revisions as in Linux in order to make the comparison more
clear.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Merge mxc_setup_config1() into board_nand_init() in order to ease the addition
of i.MX5 support in the following patches.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mxc_nand_read_page_raw_syndrome() should reenable ECC upon exit. This fixes ECC
errors left uncorrected after a call to this function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use _mxc_nand_enable_hwecc() instead of duplicating its code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the NFC IP 1.1, the 32-bit ecc_status_result value comes from 2
consecutive 16-bit registers. This patch reads all the fields of this value,
which makes a difference for 4-kiB NF pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is based on Linux kernel -next:
commit 14f44abf1dafc20ba42ce8616a8fc8fbd1b3712b
Author: Brian Norris <computersforpeace@gmail.com>
Date: Fri Jul 13 09:28:24 2012 -0700
mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND_CMD_ constants for lock/unlock should be in the header
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
This is commit 637957551c0ac80de8dfc7650d320c5a98c2c0c0 from Linux
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[scottwood@freescale.com: picked from Linux into U-Boot]
Reported-by: Rafael Beims <rafael.beims@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Warning is:
xilinx_spi.c: In function 'spi_setup_slave':
xilinx_spi.c:81: warning: unused variable 'regs'
Signed-off-by: Stephan Linz <linz@li-pro.net>
CC: Michal Simek <monstr@monstr.eu>
Initialize all possible uartlites and return the first
initialized port. For static configuration is initialization
done in userial_ports array.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
Use CONFIG parameters only at one location to simplify
the code. Also create ace_readw/writew functions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There were a couple of drivers that were actually using the flags
field of the cmd structure, despite the fact that no one ever
*set* that field. When we removed the field, those drivers failed
to compile. Replaced the references with the correct usage of
resp_type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Samsung SoC use the cmu control to set clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Samsung SoC is broken busy waiting for R1b type.
And clk delay control value is modified the previosuly value.
(that value used at the s5p_mmc.c)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some boards have no Card Detect wired. In that case, set the CD test
bits in the standard interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When setting up the clocks in the sdhci driver, the "spec version"
must be masked off. Otherwise any time the vendor version is not 0,
the check will allways assume the interface is version 3. This breaks
when the interface is actually version 1 or 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since the type of "ext_csd" was array of char, the following
calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT]
was minus.
capacity = ext_csd[EXT_CSD_SEC_CNT] << 0
| ext_csd[EXT_CSD_SEC_CNT + 1] << 8
| ext_csd[EXT_CSD_SEC_CNT + 2] << 16
| ext_csd[EXT_CSD_SEC_CNT + 3] << 24;
So, this patch changes the type of "ext_csd" to array of u8.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The controller can control high capacity cards. So, the patch adds
the flag. If the flag is not set, "mmcinfo" will fail when a high
capacity card is used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
(!timeout) condition check in mmc_send_status() can never be met,
because do-while loop ends up with negative timeout value, -1.
Fix the check to handle TIMEOUT case correctly.
Signed-off-by: Jongman Heo <jongman.heo@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'master' of git://git.denx.de/u-boot-avr32:
net:macb: add line break
avr32:portmux: fix setup for macb1
avr32: Remove redundant LDSCRIPT definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Without this patch we see annoying output like this:
---8<---
U-Boot> dhcp
macb1: PHY not foundmacb0: PHY present at 1
macb0: Starting autonegotiation...
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Check for ctrlc() in operations that take time and loop over the flash
addresses.
In netconsole, tstc() is expensive. Only check once in a while to not
slow down the operation significantly.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added an optional check in the CFI driver to evaluate if the sector is
already blank before issuing an erase command. Improves erase time by
over a factor of 10 if already blank.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On Microblaze with device tree support enabled we run into
the error below.
I'm not sure, but I think that all source code should include
at least the common.h and just this fix the problem on
Microblaz architecture.
The error is:
In file included from key_matrix.c:29:
include/malloc.h:364: error: conflicting types for 'memset'
include/linux/string.h:71: error: previous declaration of 'memset' was here
include/malloc.h:365: error: conflicting types for 'memcpy'
include/linux/string.h:74: error: previous declaration of 'memcpy' was here
Signed-off-by: Stephan Linz <linz@li-pro.net>
CC: Bernie Thompson <bhthompson@chromium.org>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Warren <twarren@nvidia.com>
CC: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>
This driver uses the century bit of this RTC in the opposite way Linux does.
From Linux's rtc-pcf8563.c:
/*
* The meaning of MO_C bit varies by the chip type.
* From PCF8563 datasheet: this bit is toggled when the years
* register overflows from 99 to 00
* 0 indicates the century is 20xx
* 1 indicates the century is 19xx
* From RTC8564 datasheet: this bit indicates change of
* century. When the year digit data overflows from 99 to 00,
* this bit is set. By presetting it to 0 while still in the
* 20th century, it will be set in year 2000, ...
* There seems no reliable way to know how the system use this
* bit. So let's do it heuristically, assuming we are live in
* 1970...2069.
*/
As U-Boot's PCF8563 driver does not say it is supposed to support the RTC8564,
make this driver compatible with Linux's by giving the opposite meaning to the
century bit.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
Introduce CONFIG_PCI_ENUM_ONLY variable for platforms that just want a
quick enumberation of the PCI devices, but don't need any setup work done.
This is very beneficial on platforms that have u-boot loaded by another
boot loader which does a more sophisticated job of setup of PCI devices
than u-boot. That way, u-boot can just read what's there and get on
with life. This is what SeaBIOS does.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
Refactor the common PCI code just a tiny bit surrounding the PCI_PNP
(pciauto) stuff. Makes the code a tiny bit easier to read, and also
makes it more obvious that almost no platform needs to setup or use the
pci_config_table stuff.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
I tried to clean up the white space and formatting offenses and
inconsistencies in the generic PCI code that obviously has been around for
some time. Emphasis on large increases in readability and maintainability
and consistency. I omitted the platform/processor specific files in
the drivers/pci directory because I wanted to leave those file to those
that care more about them.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
In a couple of places, unsigned int and pci_config_*_dword were being
used when u16 and _word should be used. Unsigned int was also being
used in a couple of places that should be pci_addr_t.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
tx25: Use generic gpio_* calls
config: Always use GNU ld
tools: add kwboot binary to .gitignore file
fdt: Include arch specific gpio.h instead of asm-generic/gpio.h
serial: CONSOLE macro is not used
Conflicts:
board/karo/tx25/tx25.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.
To use PMECC in this driver, the user needs to set the PMECC correction
capability, the sector size and ROM lookup table offsets in board config file.
This driver is ported from Linux kernel atmel_nand PMECC patch. The main difference
is in this version it uses registers structure access hardware instead of using macros.
It is tested in 9x5 serial boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>