Both the distro boot configuration as well as the general pxe support
standardized on fdtfile as the variable to hold the dtb filename.
Adjust to follow that such that e.g. "pxe boot" will just work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently "bootcmd" does not work as intended but instead prints MMC usage
information and goes directly to "nandboot".
Follow what the commit 669681104d ("configs: Fix usage of mmc rescan")
does for other boards prior to support for TechNexion TAO3530 SoM was
added.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
When running 'run_fit' the FIT file should have been loaded at
'addr_fit', although at this point they should be the same
use this variable instead of 'loadaddr'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Add support to boot the MCU domain R5F Core0 remoteproc at U-boot prompt
on the AM65x EVM boards by using the 'boot_rprocs' and other env variables
defined in the common environment file k3_rproc.h, and updating the
'DEFAULT_RPROCS' macro.
The default configuration is to use the MCU R5F in Split mode, so both
the R5F Core0 and Core1 are started before loading and booting the Linux
kernel using the following firmware:
MCU R5FSS0 Core0 (Split) : 0 /lib/firmware/am65x-mcu-r5f0_0-fw
MCU R5FSS0 Core1 (Split) : 1 /lib/firmware/am65x-mcu-r5f0_1-fw
The MCU R5FSS was initially running the R5 SPL in LockStep mode with ATCM
disabled, and is actually shutdown to enable it to be reconfigured and
booted by either A53 U-Boot or Linux kernel in remoteproc mode and using
ATCM.
The MCU R5FSS would need to be reconfigured for Lockstep mode through
DT if a fault-tolerant/safety application were to be run on the cluster
with the DEFAULT_RPROCS macro updated to remove the Core1 firmware.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support to boot some remoteprocs at U-boot prompt on the J721E EVM
boards by using the 'boot_rprocs' and other env variables defined in the
common environment file k3_rproc.h, and updating the 'DEFAULT_RPROCS'
macro.
The list of R5F cores to be started before loading and booting the Linux
kernel are as follows, and in this order:
Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7-main-r5f0_1-fw
Main R5FSS1 (LockStep) : 4 /lib/firmware/j7-main-r5f1_0-fw
The MCU R5FSS0 and Main R5FSS1 are currently in LockStep mode, so the
equivalent Core1 rprocs (rproc #1 and #5) are not included. The Main
R5FSS0 Core0 (rproc #2) is already started by R5 SPL, so is not included
in the list either.
The DSP cores are started in the following order before loading and
booting the Linux kernel:
C66_0: 6 /lib/firmware/j7-c66_0-fw
C66_1: 7 /lib/firmware/j7-c66_1-fw
C71_0: 8 /lib/firmware/j7-c71_0-fw
The order of the rprocs to boot can be changed at runtime if desired by
overwriting the 'rproc_fw_binaries' environment variable at U-boot prompt.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
Use distro_bootcmd as default bootcmd instead of legacy wrappers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Use distro_bootcmd as defauult bootcmd instead of legacy wrappers.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Since recent splash changes common code for splashscreen logo
should be used instead of adding duplicated code under board
directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations
used old board specific logo code and do not link, fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover,
the SYSRESET_WATCHDOG driver is used to support 'reset' command.
As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is
enabled for it. This allows the legacy SPL code to work properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).
The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add Falcon mode support, which allows the SPL to load and
jump to the Linux kernel directly, without the need of loading
U-Boot proper.
CONFIG_SPL_OS_BOOT=y needs to be passed in the defconfig
in order to use Falcon mode.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
We should use a common script to allow booting the U-Boot console as
fallback so we ended using a 'default_boot' and 'base_boot'
environment scripts to accomplish that.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add the boot menu option for the NYMPH baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The first stage of flash.bin is larger than 584 * 512, so when
writting u-boot.itb, some data will be override. Enlarge the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since commit 6e1f4d2652 ("arm: imx-common: add SECURE_BOOT option
to Kconfig") the SECURE_BOOT option is selected through Kconfig.
Cleanup comments in code to align with this change.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The whole cache code needs to be redesign to read information about cache
from DT instead of macro selection. Enable caches by default because
systems have caches on by default for Linux.
Also enable CMD_CACHE to be able to disable cache if there is any issue.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_SYS_BOOT_RAMDISK_HIGH is already defined in
arch/arm/include/asm/config.h:10:#define CONFIG_SYS_BOOT_RAMDISK_HIGH
that's why there is no reason to define it again in board file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms have been moved to distro boot that's why remove the rest of
configurations to have unified boot flow.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Follow conventions and used {} around variables.
Fixes: 90e97ab31e ("arm: zynq: Define distro boot commnads for qspi, nand and nor")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are two typos in this command that's why it couldn't work properly.
This bootmode is almost unused from the beggining on this SoC.
Fixes: 90e97ab31e ("arm: zynq: Define distro boot commnads for qspi, nand and nor")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>