Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
cpu_init_crit can be skipped, but the code is still enabled requiring a
platform to supply lowlevel_init.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
CONFIG_MACH_TYPE is used to set the machine type number in the
common arm code instead of setting it in the board code.
Boards with dynamically discoverable machine types can still set the
machine type number in the board code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
On i.MX27, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
On i.MX5, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Offsets to registers may be needed in asm code. This patch adds automated
generation of these offsets form C structures.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
mx27_uart_init_pins does the IOMUX setting for UART1 port.
Change the function name to make the UART port number explicit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
asm-offsets.h should be auto generated. This patch adds two rules to rules.mk
which makes this possible and removes the rules on imx35.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a
bank soft-reset after the bank was configured and enabled, even though
enabling a bank causes it to reset. Because the reset was required for
multiple errata, it was not properly enclosed in an #ifdef, and so was
not removed with all the other rev1 errata work-arounds.
Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if
bank 2 is enabled, but this was not being done for SERDES protocols 0xF
and 0x10. The bank reset also happened to enable bank 3 (apparently an
undocumented feature). Simply removing the reset breaks these two
protocols.
It turns out that every time we call enable_bank(), we do want at least
one lane of the bank enabled, either because the bank is supposed to be
enabled, or because we need the clock from that bank enabled.
For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we
call enable_bank(), because that array is used elsewhere to determine if
the bank is available.
Note that the side effect of these changes is that the work-arounds for
these two errata are now linked. Specifically, if SERDES-A001 is
enabled, then we need SERDES-8 enabled as well.
Because this was the only SERDES bank soft-reset, there is no need to
implement a work-around for erratum SERDES-A003.
Also fix an off-by-one error in a printf().
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ed Swarthout <swarthou@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.
Signed-off-by: York Sun <yorksun@freescale.com>
Modify support for USB mode fixup:
- Add common support for USB mode and phy type
device tree fix-up for all USB controllers
mentioned in hwconfig string
- Fetch USB mode and phy type via hwconfig; if not
defined in hwconfig, then fetch them from env
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has
data width and primary sdram width. The latter one has different meaning
for DDR3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In case of empty SPD or checksum error, fallback to raw timing on
supported boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We used to have fixed parameters for soldered DDR chips. This patch
introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing
data from DDR chip datasheet, implemneted in board-specific files or header
files.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On P1022/P1013 second USB controller is muxed with second
Ethernet controller. The current code to enable second USB
fails to properly clear pinmux bits used by ethernet. As a
result, Linux freezes when this controller is used. This
patch fixes the problem.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only use DDR DIMM part number if SPD has valid length, to prevent from
display garbage in case SPD doesn't cover these fields.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the bus width is 32-bit, burst chop should be disabled and burst length
should be 8. Read from SPD or other source to determine the width.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LBC code to handle the case in which
CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On a 8308 based board it was found that the PEX_GLK_RATIO register
(programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This
was tracked to the fact that the pci express clock frequency was not being
assigned to the pciexp1_clk entry in the global data structure in file
arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in
'do_clocks' command.
Signed-off-by: Bill Cook <cook@isgchips.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
CPO value and driver strength settings are board specifc.
Also allow SPD data fetch from any accessible I2C EEPROM.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Running on mpc837x without CONFIG_FSL_ESDHC leads to
i2c1_clk not being set at all. It is bound to clock
of encryption module. fix this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Some boards e.g. keymile arm boards have CONFIG_CMD_I2C switched on
but they use soft i2c on kirkwood. So don't switch CONFIG_I2C_MVTWSI
on in this case.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
* Fix compiler error for cpu at91sam9, if lowlevel init is enabled
* use correct ATMEL_ name scheme to define ATMEL_BASE_SDRAMC
Signed-off-by: Jens Scharsig
This is a copy of arm926ejs/at91 api for perpherial initialisation.
At the moment we just need the usart part of the api.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch enables the new clock features from arm920t/at91/clock.c. This
is an required step to get at91rm9200_usart replaced by atmel_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Jens Scharsig <js_at_ng@scharsoft.de>
Cc: Eric Bénard <eric@eukrea.com>
This patch adds an copy of arm926ejs/at91/clock.c to arm920t/at91. The
arm926ejs specialities are removed from arm920t version and vice versa.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch sets the ATMEL_PMX_AA_TXD2 to the correct value.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Jens Scharsig <js_at_ng@scharsoft.de>
CC: eric@eukrea.com
Acked-by: Eric Bénard <eric@eukrea.com>
As implemented now the timer used to implement __udelay counts
to 0xffffffff and then gets stuck there because the the programmed
reload value is 0xffffffff. This value is not only wrong but
illegal according to the reference manual.
One can reproduce the bug by leaving a board at the u-boot prompt
for sometime then issuing a sleep command. The sleep will hang
forever.
The timer is a count up timer that reloads as it rolls over
from 0xffffffff so the correct load value is 0.
Change TIMER_LOAD_VAL from 0xffffffff to 0 and introduce
a new constant called TIMER_OVERFLOW_VAL set to 0xffffffff.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430
Add support for some of the key PL310 operations
- Invalidate all
- Invalidate range
- Flush(clean & invalidate) all
- Flush range
Signed-off-by: Aneesh V <aneesh@ti.com>
1. make sure that page table setup is not done multiple times
2. flush_dcache_all() is more appropriate while disabling cache
than a range flush on the entire memory(flush_cache())
Provide a default implementation for flush_dcache_all()
for backward compatibility and to avoid build issues.
Signed-off-by: Aneesh V <aneesh@ti.com>
- Enable I-cache on bootup
- Enable MMU and D-cache immediately after relocation
- Do necessary initialization before enabling d-cache and MMU
- Changes to cleanup_before_linux()
- Make changes according to the new framework
Signed-off-by: Aneesh V <aneesh@ti.com>
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
