Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.
This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Suggested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There is a hole in shadow registers address map of size 0x100
between bank 5 and bank 6 on iMX6QP, iMX6DQ, iMX6SDL, iMX6SX and iMX6UL.
Bank 5 ends at 0x6F0 and Bank 6 starts at 0x800. When reading the fuses,
we should account for this hole in address space.
Similar hole exists between bank 14 and bank 15 of size
0x80 on iMX6QP, iMX6DQ, iMX6SDL and iMX6SX.
Note: iMX6SL has only 0-7 banks and there is no hole.
Note: iMX6UL doesn't have this one.
When reading, we use register offset, so need to account for holes
to get the correct address.
When writing, we use bank/word index, there is no need to account
for holes, always use bank/word index from fuse map.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Add LPDDR2 support:
1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2.
2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to
mx6_ddr3_cfg, but still keep it a single one for easy to choose
parameters for LPDDR2.
3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC.
4. Update comments.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add ddr_type entry for mx6_ddr_sysinfo. It will be used for
differenrate DDR3 and LPDDR2.
Introduce an enum type for ddr_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Add mpzqlp2ctl entry for mx6_mmdc_calibration.
MMDC_MPZQLP2CTL register is for init tZQINIT, tZQCL, tZQCS for LPDDR2 chips.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs.
Add a new function mx6sl_dram_iocfg to configure dram io.
Add header file to define macros for register address.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
* Add mxc_gpio support for imx7d SoC
* Use CONFIG_MX7 to extend mxc gpio driver support for imx7d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* Add imx7d support for iomux controller
* imx7d has two iomux controllers iomuxc (0x3033000) and iomuxc-lpsr
(0x302C0000) each conroller provides control and mux mode pad
registers but shares iomuxc input select register with iomuxc-lpsr
IOMUX_CONFIG_LPSR flag is used to properly set daisy chain settings
for iomuxc-lpsr pads.
* Since mx7d introduces LPSR IOMUX pins, add new base to IOMUX v3
driver for these LPSR pins.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Move most macro definitions and prototypes into
"arch/arm/include/asm/imx-common/sys_proto.h" to avoid duplicated
function prototypes and marco definitions for different i.MX SoCs.
This patch do not remove the sys_proto.h for different i.MX SoCs,
because we need to modify lots of driver code and others. This patch
remove duplicated macros and prototypes and incude "sys_proto.h"
of imx-common for each sys_proto.h of different i.MX platforms.
Then later we should avoid add stuff in sys_proto.h of each platform,
and modify driver to include common sys_proto.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rewrite get_cpu_rev, from "static const char *get_cpu_rev(void)" to
"u32 get_cpu_rev(void)". To align with get_cpu_rev of other i.MXes.
Also write get_imx_type to replace get_cpu_type, since we have
macro named get_cpu_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Use new formula for get_cpu_rev, since we need to use this formula
to do runtime check for all i.MXes.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch rewrites MMU translation table entries. To start, all table
entries are written as "invalid", then "device-ngnrnr" and "normal" are
written to the entries to enable access to specific addresses.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ISBC Key Extension feature is not applicable for RAMBOOT
as there is no way to retrieve the CSF Header and validated
IE Key table from SRAM once CPC has been disabled.
The feature is only applicable in case of NOR SECURE BOOT.
Code Cleanup:
The SECURE_BOOT specific defines have been moved from
arch-ls102xa/config.h to
arm/include/asm/fsl_secure_boot.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds a minimal framework for Dickens CCN-504
interconnect configuration - mainly related to adding Clusters/cores
to snoop/DVM domain and setting QoS of the RN-I ports.
LS2085A platform makes use of these configurations to support
better network data performance and to boot a SMP Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.
On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in omap5 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in beagle_x15 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
This patch moves pxa to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) pxa timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locked the processor. Rather than patch the specific pxa issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsuiko.com>
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
