Commit Graph

49729 Commits

Author SHA1 Message Date
Heinrich Schuchardt
95058fbb97 env: mmc/fat/ext4: undefined reference to `mmc_initialize'
For CONFIG_ENV_FAT_INTERFACE != 'mmc' a link error
env/fat.c:93: undefined reference to `mmc_initialize'
occurs if CONFIG_MMC_SUPPORT is not enabled.

Fixes: 26862b4a40 ("env: mmc/fat/ext4: make sure that the MMC sub-system
is initialized before using it")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-04-16 18:45:35 -04:00
Siva Durga Prasad Paladugu
7bcdf19572 env: Relocate env drivers if manual reloc is required
Relocate env drivers if manual relocation is enabled. This
patch fixes the issue of u-boot hang incase if env is
present in any of the flash devices.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 18:45:35 -04:00
Sjoerd Simons
90e407ae01 Kconfig: Enlarge default SYS_MALLOC_F_LEN for AM33XX
Since commit 8e14ba7bd5 ("gpio: omap_gpio: Add DM_FLAG_PRE_RELOC
flag") omap GPIO gets bound before relocation.  Unfortunately due to
this, on at least the beaglebone black, the pre-relocation memory pool
gets exhausted before probing the serial port. This then causes u-boot
to panic as CONFIG_REQUIRE_SERIAL_CONSOLE is set...

Resolve this by resizing the default size of the pre-relocation malloc
pool for AM335X platforms.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2018-04-16 18:45:35 -04:00
Alexander Graf
4f67b93fb7 part: Disable CONFIG_SPL_ISO_PARTITION by default
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-16 18:45:35 -04:00
Tom Rini
9d24b01ce0 Merge git://git.denx.de/u-boot-x86 2018-04-16 13:24:20 -04:00
Simon Glass
d5032392ba x86: Rename coreboot-x86 to coreboot
We only use coreboot as a target on x86 platforms, since on ARM platforms
U-Boot always runs as the primary boot loader. Rename the coreboot-x86
platform to reflect this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 22:38:53 +08:00
Bin Meng
7d9974a2be doc: vxworks: Update x86 specific instructions
This updates the doc of booting VxWorks, like loading an x64 kernel,
and how to make VxWorks graphics console driver work.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 22:38:53 +08:00
Bin Meng
79c584e559 bootvx: x86: Assign bootaddr based on kernel memory base
On VxWorks x86 its bootline address is at a pre-defined offset @
0x1200. If 'bootaddr' is not passed via environment variable, we
assign its value based on the kernel memory base address.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 22:38:53 +08:00
Bin Meng
ced71a2f72 bootvx: Exit if bootline address is not specified
Exit the 'bootvx' command if bootline address is not specified.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 22:38:53 +08:00
Bin Meng
7824ad6ad4 bootvx: Refactor the bootline copy codes a little bit
There is a small duplication in do_bootvx() that does the bootline
copy. Refactor this a little bit to make it simpler.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:52 +08:00
Bin Meng
447ae4f7ad bootvx: x86: Make VxWorks EFI console driver happy
When booting from EFI BIOS, VxWorks bootloader stores the EFI GOP
framebuffer info at a pre-defined offset @ 0x6100. When VxWorks
kernel boots up, its EFI console driver tries to find such a block
and if the signature matches, the framebuffer information will be
used to initialize the driver.

However it is not necessary to prepare an EFI environment for
VxWorks's EFI console driver to function (eg: EFI loader in
U-Boot). If U-Boot has already initialized the graphics card and
set it to a VESA mode that is compatible with EFI GOP, we can
simply prepare such a block for VxWorks.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:52 +08:00
Bin Meng
611309383d pci: video: Only print out when everything is OK
If video initialization fails, the "Video:" output message will be
mixed with the next console log. Change to print out such message
only when everything is OK, which improves the boot log readability.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:52 +08:00
Bin Meng
55b4e1b7d9 x86: Change default FRAMEBUFFER_VESA_MODE of some boards
This changes some boards' default FRAMEBUFFER_VESA_MODE to use 32-bit
pixel format for better VxWorks compatibility.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:52 +08:00
Bin Meng
17b07d70be video: vesa: Change default FRAMEBUFFER_VESA_MODE
This changes the default FRAMEBUFFER_VESA_MODE to use 32-bit pixel
format for better VxWorks compatibility.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:51 +08:00
Bin Meng
ca5eb0c5fb bios: vesa: Guard setting vesa mode with CONFIG_FRAMEBUFFER_SET_VESA_MODE
If CONFIG_FRAMEBUFFER_SET_VESA_MODE is not set, don't switch
graphics card to VESA mode. This applies to both native mode
and emulator mode of running the VGA BIOS.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 22:38:35 +08:00
Tom Rini
282f15804b Merge git://git.denx.de/u-boot-cfi-flash 2018-04-16 08:31:17 -04:00
Bin Meng
839c4e9c5b elf: Add a very simple ELF64 loader
This adds a very simple ELF64 loader via program headers, similar
to load_elf_image_phdr() that we already have.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 16:54:51 +08:00
Bin Meng
2bce3f595d elf: Add ELF64 related structure defines
This adds ELF header, program header and section header structure
defines for the 64-bit ELF image.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 16:54:51 +08:00
Bin Meng
df635df2e0 elf: Clean up the ELF header file
Fix various style violations in elf.h
- use correct comment format if the comment fits in just one line
- remove the ending period for the one-line comment
- use tab for the indention instead of space
- put the opening brace at the same line of a typedef/union
- remove <name> in a 'typedef struct' for consistency

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Bin Meng
45519924a0 x86: Rename e820entry to e820_entry
This changes 'struct e820entry' to 'struct e820_entry' to conform
with the coding style.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Bin Meng
87af71c2ea x86: Use 'unsigned int' in install_e820_map() functions
This fixes the following checkpatch warning:

  warning: Prefer 'unsigned int' to bare use of 'unsigned'

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Bin Meng
fa5e91f778 vxworks: x86: Rename e820info to e820_info
This changes 'struct e820info' to 'struct e820_info' to conform
with the coding style.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Bin Meng
1351700cf2 bootvx: x86: Explicitly clear the bootloader image size
VxWorks bootloader stores its size at a pre-defined offset @ 0x5004.
Later when VxWorks kernel boots up and system memory information is
retrieved from the E820 table, the bootloader size will be subtracted
from the total system memory size to calculate the size of available
memory for the OS.

Explicitly clear the bootloader image size otherwise if memory
at this offset happens to contain some garbage data, the final
available memory size for the kernel is insane.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-04-16 16:54:51 +08:00
Bin Meng
2902be86c1 bootvx: x86: Prepare e820 related stuff from the given kernel memory base address
At present two environment variables 'e820data'/'e820info' are required
to boot a VxWorks x86 kernel, but this is superfluous. The offset of
these two tables are actually at a fixed offset from the kernel memory
base address and we can provide the kernel memory base address to U-Boot
via only one variable 'vx_phys_mem_base'.

Note as it name indicates, the physical address should be provided.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Bin Meng
2ad3d088d2 doc: vxworks: Minor update for clarity
This corrects a typo and updates several places for clarity.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2018-04-16 16:54:51 +08:00
Lukasz Majewski
014d7b13ae x86: Update the io.h file to use {out|in}_{be|le}X macros
The commit 3f70a6f577 ("x86: Add clr/setbits functions")
introduced the {read|write}_ macros to manipulate data.

Those macros are not used by any code in the u-boot project (despite the
io.h itself). Other architectures use io.h with {in|out}_* macros.

This commit brings some unification across u-boot supported architectures.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 16:54:51 +08:00
Ivan Gorinov
53cabe3d8e x86: Add 64-bit memory-mapped I/O functions
Add readq() and writeq() definitions for x86.

Please note: in 32-bit code readq/writeq will generate two 32-bit
memory access instructions instead of one atomic 64-bit operation.

Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-04-16 16:54:51 +08:00
Mario Six
8bfeb33c46 mtd: cfi_flash: Make live-tree compatible
Make the cfi_flash driver compatible with a live device tree.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-04-16 09:55:59 +02:00
Tom Rini
ebca902aeb Merge git://git.denx.de/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 08:43:50 -04:00
Tom Rini
df13a44377 Merge git://git.denx.de/u-boot-net 2018-04-15 08:42:37 -04:00
Tom Rini
6d0409f256 Merge git://git.denx.de/u-boot-sh 2018-04-15 08:42:08 -04:00
Jon Nettleton
b4e9bdcd05 mx6cuboxi: Fix some memory configuration errors
These changes bring mainline back into line with the configurations
that were originally set in our stable BSP.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:56:21 +02:00
Trent Piepho
f916757300 imx: Create distinct pre-processed mkimage config files
Each imx image is created by a separate sub-make and during this process
the mkimage config file is run though cpp.

The cpp output is to the same file no matter what imx image is being
created.

This means if two imx images are generated in parallel they will attempt
to independently produce the same pre-processed mkimage config file at
the same time.

Avoid the problem by making the pre-processed config file name unique
based on the imx image it will be used in.  This way each image will
create a unique config file and they won't clobber each other when run
in parallel.

This should fixed the build bug referenced in b5b0e4e3 ("imximage:
Remove failure when no IVT offset is found").

Cc: Breno Lima <breno.lima@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:55:23 +02:00
Tom Rini
448fc44fb8 mx31ads: Delete
This platform has been marked as orphaned since September 2013, remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 11:54:02 +02:00
Tom Rini
bcca8aa9ee imx31_phycore: Delete
This platform has been marked as orphaned since September 2013, remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15 11:52:39 +02:00
Vanessa Maegima
ebca6013c0 pico-imx7d: Replace fatload command
Replace fatload with the fs generic loading interface ('load' command).

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:49:29 +02:00
Bryan O'Donoghue
723f8359c1 imx: mx7: snvs: Add an SNVS init routine
Working with HAB on the i.MX7 we've encountered a case where a board that
successfully authenticates u-boot when booting Linux via OPTEE subsequently
fails to properly bring up the RTC.

The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.

The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero. In ordinary
circumstances this is OK since we typically do not run in TZ mode, however
when we boot via HAB and enablng TrustZone, it is required to set
HPCOMR::NPSWA_EN = 1 in order for the upstream Linux driver to have
sufficient permissions to manipulate the SNVS-LP block.

On our reference board it is the difference between Linux doing this:

root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000021 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000000 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x80002100 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
         30370000.snvs:snvs-rtc-lp as rtc0
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to2018-04-01 00:51:04 UTC (1522543864)

and doing this:

root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000020 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000001 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x00002020 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: failed to enable rtc -110
snvs_rtc: probe of 30370000.snvs:snvs-rtc-lp failed with error -110
hctosys: unable to open rtc device (rtc0)

Note bit 1 of LPCR is not set in the second case and is set in the first
case and that bit 31 of HPCOMR is set in the second case but not in the
first.

Setting NPSWA_EN in HPCOMR allows us to boot through enabling TrustZone
and continue onto the kernel. The kernel then has the necessary permissions
to set LPCR::SRTC_ENV (RTC enable in the LP command register) whereas in
contrast - in the failing case the non-privileged kernel cannot do so.

This patch adds a simple init_snvs() call which sets the permission-bit
called from soc.c for the i.MX7. It may be possible, safe and desirable to
perform this on other i.MX processors but for now this is only tested on
i.MX7 as working.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2018-04-15 11:48:44 +02:00
Lukasz Majewski
b04ff9bf0f boot: script: The boot.scr file for K+P's boards
By using this file one can avoid cluttering <board>.h file with u-boot
HUSH commands necessary for booting target device.

With such approach the commands are stored only in one place and can be
reused if needed.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-04-15 11:47:35 +02:00
Lukasz Majewski
dd4671cb3f imx: board: Add support for the K+P's kp_imx6q_tpc board
This commit provides support for Kieback & Peter GmbH IMX6Q based
TPC board.

U-boot console output:

U-Boot SPL 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)
Trying to boot from MMC1

U-Boot 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 37C
Reset cause: POR
Board: K+P KP_IMX6Q_TPC i.MX6Q
       Watchdog enabled
I2C:   ready
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Autoboot in 3 seconds
2018-04-15 11:47:19 +02:00
Ian Ray
6c0e6b45f9 board: ge: bx50v3: enable backlight on demand
Enable display backlight only if a message needs to be displayed.
The kernel re-initializes the backlight, which results in some
unwanted artifacts.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-04-15 11:46:20 +02:00
Ken Lin
7a0ce1f797 arm: imx: Add Winbond SPI-NOR support for Advantech DMS-BA16 board
Windbond's been in the AVL list and need to enable the support

Signed-off-by: Ken Lin <yungching0725@gmail.com>
2018-04-15 11:45:09 +02:00
Bryan O'Donoghue
49e6242673 imx: hab: Provide hab_auth_img_or_fail command
This patch adds hab_auth_img_or_fail() a command line function that
encapsulates a common usage of authenticate and failover, namely if
authenticate image fails, then drop to BootROM USB recovery mode.

For secure-boot systems, this type of locked down behavior is important to
ensure no unsigned images can be run.

It's possible to script this logic but, when done over and over again the
environment starts get very complex and repetitive, reducing that script
repetition down to a command line function makes sense.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
2018-04-15 11:44:13 +02:00
Bryan O'Donoghue
f4d8fccd38 imximage: Encase majority of header in __ASSEMBLY__ declaration
Subsequent patches will want to include imageimage.h but in doing so
include it on an assembly compile path causing a range of compile errors.
Fix the errors pre-emptively by encasing the majority of the declarations
in imximage.h inside an ifdef __ASSEMBLY__ block.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
2018-04-15 11:44:13 +02:00
Bryan O'Donoghue
852cc548b3 warp7: Set u-boot serial# based on OTP value
u-boot has a standard "serial#" environment variable that is suitable
for storing the iSerial number we will supply via the USB device
descriptor. serial# is automatically picked up by the disk subsystem in
u-boot - thus providing a handy unique identifier in /dev/disk/by-id as
detailed below.

Storing the hardware serial identifier in serial# means we can change the
serial# if we want before USB enumeration - thus making iSerial automatic
via OTP but overridable if necessary.

This patch reads the defined OTP fuse and sets environment variable
"serial#" to the value read.

With this patch in place the USB mass storage device will appear in
/dev/disk/by-id with a unique name based on the OTP value. For example

/dev/disk/by-id/usb-Linux_UMS_disk_0_WaRP7-0xf42400d3000001d4-0:0

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:44:13 +02:00
Bryan O'Donoghue
1ab1ffded4 imx: mx7: Add comment to describe OTP TESTER registers
The tester registers provide a unique chip-level identifier which
get_board_serial() returns in a "struct tag_serialnr".

This patch documents the properties of the registers; in summary.

31:0 OCOTP_TESTER0 (most significant)
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID

OCOTP_TESTER1 (least significant)
31:24
- The X-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
  ID
23:16
- The Y-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
  ID
15:11
- The wafer number of the wafer on which the device was fabricated/SJC
  CHALLENGE/ Unique ID
10:0
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID

The 64 bits of data generate a unique serial number per-chip.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:44:13 +02:00
Bryan O'Donoghue
ca83182226 imx: mx7: Fix CONFIG_SERIAL_TAG compilation
Currently when we define CONFIG_SERIAL_TAG we will barf with a failure to
define "struct tag_serialnr".

This structure is defined in <asm/setup.h>, this patch includes
<asm/setup.h> to fix.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-15 11:44:13 +02:00
Marek Vasut
14eeb683a8 ARM: mx6: ddr: Add write leveling correction code
When the DDR calibration is enabled, a situation may happen that it
will fail on a few select boards out of a whole production lot. In
particular, after the first write leveling stage, the MPWLDECTRLx
registers will contain a value 0x1nn , for nn usually being 0x7f or
slightly lower.

What this means is that the HW write leveling detected that the DQS
rising edge on one or more bundles arrives slightly _after_ CLK and
therefore when the DDR DRAM samples CLK on the DQS rising edge, the
CLK signal is already high (cfr. AN4467 rev2 Figure 7 on page 18).

The HW write leveling then ends up adding almost an entire cycle (thus
the 0x17f) to the DQS delay, which indeed aligns it, but also triggers
subsequent calibration failure in DQS gating due to this massive offset.

There are two observations here:
- If the MPWLDECTRLx value is corrected from 0x17f to 0x0 , then the
  DQS gating passes, the entire calibration passes as well and the
  DRAM is perfectly stable even under massive load.
- When using the NXP DRAM calibrator for iMX6/7, the value 0x17f or so
  in MPWLDECTRx register is not there, but it is replaced by 0x0 as one
  would expect.

Someone from NXP finally explains why, quoting [1]:

    "
    Having said all that, the DDR Stress Test does something that we
    do not advertise to the users. The Stress Test iself looks at the
    values of the MPWLDECTRL0/1 fields before reporting results, and
    if it sees any filed with a value greater than 200/256 delay
    (reported as half-cycle = 0x1 and ABS_OFFSET > 0x48), the DDR
    Stress test will reset the Write Leveling delay for this lane
    to 0x000 and not report it in the log.

    The reason that the DDR Stress test does this is because a delay
    of more than 78% a clock cycle means that the DQS edge is arriving
    within the JEDEC tolerence of 25% of the clock edge. In most cases,
    DQS is arriving < 5% tCK of the SDCLK edge in the early case, and
    it does not make sense to delay the DQS strobe almost a full clock
    cycle and add extra latency to each Write burst just to make the
    two edges align exactly. In this case, we are guilty of making a
    decision for the customer without telling them we are doing it so
    that we don't have to provide the above explanation to every customer.
    They don't need to know it.
    "

This patch adds the correction described above, that is if the MPWLDECTRx
value is over 0x148, the value is corrected back to 0x0.

[1] https://community.nxp.com/thread/456246

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-04-15 11:39:23 +02:00
Rasmus Villemoes
8519c9c98a tools/imximage: use 0x prefix in HAB Blocks line
The u-boot-ivt.img.log file contains 0x prefixes in the HAB Blocks line,
while the SPL.log does not. For consistency, and to make it easier to
extract and put into a .csf file for use with NXP's code signing tool,
add 0x prefixes here.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
2018-04-15 11:35:21 +02:00
Rasmus Villemoes
0658761733 Makefile: always preserve output for images that can contain HAB Blocks
The current makefile logic disables creation of the
SPL.log/u-boot-ivt.img.log etc. files when V=1 is given on the command
line, the rationale presumably being that the user wants and gets the
information on the console.

However, from general principles, I don't think a higher V= level
should affect which build artifacts get generated (and certainly
shouldn't produce fewer). Concretely, it's also a problem that when
doing a V=1 build in a terminal, the relevant HAB blocks lines easily
drown in all the other V=1 output.

Moreover, build systems such as Yocto by default pass V=1, so in that
case the information gets hidden away in the do_compile log file, making
it nigh impossible to create a recipe for creating signed U-boot images
- I don't want to disable V=1, because having verbose output in the log
file is valuable when things go wrong, but OTOH trying to go digging in
the do_compile log file (and getting exactly the right lines) is not
pleasant to even think about.

So change the logic so that for V=0, the mkimage output is redirected
to MKIMAGEOUTPUT (which is also the current behaviour), while for any
other value of V, we _additionally_ write the information to make's
stdout, whatever that might be.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Breno Lima <breno.lima@nxp.com>
2018-04-15 11:35:04 +02:00
Marek Vasut
cb0b6b035a mmc: tmio: Rename Matsushita to TMIO
Synchronize the naming with Linux, call the common code TMIO.
No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-14 00:03:30 +02:00