This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.
If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Unify the register structure so they can be easily used across all
of S3C24xx lineup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Generate the PSCI node in the device tree.
Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.
This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
before entering the payload
- performing an exception return from secure mode directly into
the payload
- allowing the code to be dynamically relocated to secure RAM
before switching to non-secure.
This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.
Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Renesas R8A7794 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.
These settings now match the i.MX6 Dual and Quad core versions.
Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
There is no way to reset the cpu, so use the watchdog for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fix following compilation error when CONFIG_ARM64 is defined
Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'
Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.
cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
