Commit Graph

544 Commits

Author SHA1 Message Date
Jason Liu
bc5833c49a i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite board
Add the initial support for Freescale i.MX6Q Sabre Lite board

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
2012-01-16 08:40:10 +01:00
Wolfgang Denk
670c24f6f3 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  fsl_lbc: add printout of LCRR and LBCR to local bus regs
  sbc8548: Fix up local bus init to be frequency aware
  sbc8548: enable support for hardware SPD errata workaround
  sbc8548: relocate fixed ddr init code to ddr.c file
  sbc8548: Make enabling SPD RAM configuration work
  sbc8548: Fix LBC SDRAM initialization settings
  sbc8548: enable ability to boot from alternate flash
  sbc8548: relocate 64MB user flash to sane boundary
  Revert "SBC8548: fix address mask to allow 64M flash"
  MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
  eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
  eXMeritus HWW-1U-1A: Minor environment variable tweaks
2012-01-13 20:38:49 +01:00
Paul Gortmaker
3e3262bd14 sbc8548: enable support for hardware SPD errata workaround
Existing boards by default have an issue where the LBC SDRAM
SPD EEPROM and the DDR2 SDRAM SPD EEPROM both land at 0x51.

After the hardware modification listed in the README is made,
then the DDR2 SPD EEPROM appears at 0x53.  So this implements
a board specific get_spd() by taking advantage of the existing
weak linkage, that 1st tries reading at 0x53 and then if that
fails, it falls back to the old 0x51.

Since the old dependency issue of "SPD implies no LBC SDRAM"
gets removed with the hardware errata fix, remove that restriction
in the code, so both LBC SDRAM and SPD can be selected.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:59:14 -06:00
Paul Gortmaker
7e44f2b710 sbc8548: Make enabling SPD RAM configuration work
Previously, SPD configuration of RAM was non functional on
this board.  Now that the root cause is known (an i2c address
conflict), there is a simple end-user workaround - remove the
old slower local bus 128MB module and then SPD detection on the
main DDR2 memory module works fine.

We make the enablement of the LBC SDRAM support conditional on
being not SPD enabled.  We can revisit this dependency as the
hardware workaround becomes available.

Turning off LBC SDRAM support revealed a couple implict dependencies
in the tlb/law code that always expected an LBC SDRAM address.

This has been tested with the default 256MB module, a 512MB
a 1GB and a 2GB, of varying speeds, and the SPD autoconfiguration
worked fine in all cases.

The default configuration remains to go with the hard coded
DDR config, so the default build will continue to work on boards
where people don't bother to read the docs.  But the advantage
of going to the SPD config is that even the small default module
gets configured for CL3 instead of CL4.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:59:07 -06:00
Paul Gortmaker
f0aec4ea33 sbc8548: enable ability to boot from alternate flash
This board has an 8MB soldered on flash, and a 64MB SODIMM
flash module.  Normally the board boots from the 8MB flash,
but the hardware can be configured for booting from the 64MB
flash as well by swapping CS0 and CS6.  This can be handy
for recovery purposes, or for supporting u-boot and VxBoot
at the same time.

To support this in u-boot, we need to have different BR0/OR0
and BR6/OR6 settings in place for when the board is configured
in this way, and a different TEXT_BASE needs to be used due
to the larger sector size of the 64MB flash module.

We introduce the suffix _8M and _64M for the BR0/BR6 and the
OR0/OR6 values so it is clear which is being used to map what
specific device.

The larger sector size (512k) of the alternate flash needs
a larger malloc pool, otherwise you'll get failures when
running saveenv, so bump it up accordingly.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:58:14 -06:00
Paul Gortmaker
3fd673cf36 sbc8548: relocate 64MB user flash to sane boundary
The current situation has the 64MB user flash at an awkward
alignment; shifted back from 0xfc00_0000 by 8M, to leave an 8MB hole
for the soldered on boot flash @ EOM.  But to switch to optionally
supporting booting off the 64MB flash, the 64MB will then be mapped
at the sane address of 0xfc00_0000.

This leads to awkward things when programming the 64MB flash prior
to transitioning to it -- i.e. even though the chip spans from
0xfb80_0000 to 0xff7f_ffff, you would have to program a u-boot image
into the two sectors from 0xfbf0_0000 --> 0xfbff_ffff so that it was
in the right place when JP12/SW2.8 were switched to make the 64MB on
/CS0. (i.e. the chip is only looking at the bits in mask 0x3ff_ffff)

We also have to have three TLB entries responsible for dealing with
mapping the 64MB flash due to this 8MB of misalignment.

In the end, there is address space from 0xec00_0000 to 0xefff_ffff
where we can map it, and then the transition from booting from one
config to the other will be a simple 0xec --> 0xfc mapping.  Plus we
can toss out a TLB entry.

Note that TLB0 is kept at 64MB and not shrunk down to the 8MB boot
flash; this means we won't have to change it when the alternate
config uses the full 64MB for booting, in TLB0.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-11 13:58:10 -06:00
Thierry Reding
314284b156 mmc: Change board_mmc_getcd() function prototype.
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.

The rationale for this change can be found in the following email
thread:

	http://lists.denx.de/pipermail/u-boot/2011-November/110180.html

In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08 21:28:27 -06:00
Wolfgang Denk
145afab32c Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  tegra2: Optimize out-of-tree build for Ventana.
  tegra: Move boards over to use arch-level board UART function
  tegra: Add support for UART init in cpu board.c
  tegra: Add a function mux feature
  tegra: add clock_ll_start_uart() to enable UART prior to reloc
  tegra: Move clock_early_init() to arch_cpu_init()
  tegra: Move cpu_init_cp15() to arch_cpu_init()
  arm: Tegra: Fix Harmony and Ventana builds in u-boot-tegra/master
  tegra: Fix build error in plutux, medcom
  tegra2: Add Avionic Design Medcom support.
  tegra2: Add Avionic Design Plutux support.
  tegra2: Add common Avionic Design Tamonten support.
  tegra2: Move tegra2_mmc_init() prototype to public header.
  tegra2: Change CONFIG_SYS_TEXT_BASE to 0x00108000.
  tegra2: Always build with USE_PRIVATE_LIBGCC=yes.
  tegra2: Plumb in SPI/UART switch code
  tegra2: spi: Support SPI / UART switch
  tegra2: Implement SPI / UART GPIO switch
  tegra2: Enable SPI environment on Seaboard
  tegra2: config: Enable SPI flash on Seaboard
  tegra2: spi: Add SPI driver for Tegra2 SOC
  tegra2: Add UARTB support
  tegra2: Tidy UART selection
  arm, davinci: Fix build warnings for cam_enc_4xx
  Devkit8000: Switch over to enable_gpmc_cs_config
  arm, davinci: Add support for generating AIS images to the Makefile
  mkimage: Fix variable length header support
  arm, da850evm: Add an SPL for SPI boot
  arm, davinci: Add SPL support for DA850 SoCs
  sf: Add spi_boot() to allow booting from SPI flash in an SPL
  spl: display_options.o is required for SPI flash support in SPL
  ARM: omap3: add support to Technexion twister board
  ARM: omap3: added common configuration for Technexion TAM3517
  vision2: Fix checkpatch warning
2012-01-05 16:38:50 +01:00
Tom Rini
2620368a61 git-mailrc: Add self to davinci/omap, add ti
Adding a 'ti' alias since not all parts are "omap" or "davinci" and
adding myself to that alias as co-custodian of u-boot-ti

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-01-05 15:59:47 +01:00
Christian Riesch
3d2c8e6c7f arm, da850evm: Add an SPL for SPI boot
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2011-12-24 10:23:30 +01:00
Christian Riesch
32b1127397 sf: Add spi_boot() to allow booting from SPI flash in an SPL
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-12-24 10:23:30 +01:00
Horst Kronstorfer
49fbf4371e doc/mkimage.1: Fix -D/-f options formatting
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
2011-12-23 20:11:46 +01:00
Horst Kronstorfer
7aecfdd0f8 doc/mkimage.1: Fix some typos
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-12-21 20:27:18 +01:00
Wolfgang Denk
6b62b9a31d Coding Style cleanup
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-19 12:03:40 +01:00
Wolfgang Denk
3f3110d78b MIPS: remove broken "tb0229" board
The "tb0229" board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-12 14:26:48 +01:00
Marek Vasut
ea098e0fb8 M28: Document that units has to be set to sectors on SD bootcard
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2011-12-09 17:30:10 +01:00
Wolfgang Denk
fb82fd7a32 MPC850: remove obsolete "rmu" Board
The "rmu" board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08 20:51:39 +01:00
Wolfgang Denk
309a292e41 MPC8240: remove obsolete "OXC" board
The OXC board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08 20:51:33 +01:00
Wolfgang Denk
c53043b7f1 MPC7xx: remove obsolete "BAB7xx" board
The BAB7xx boards are almost deceased.  They cause build warnings, an
it's not worth the effort to fix these.  Remove the dead body.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
2011-12-08 20:51:28 +01:00
Marek Vasut
c477d72c04 PXA: Drop XM250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
d299173139 PXA: Drop PLEB2 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
00c4acaa97 PXA: Drop CRADLE board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
f13eba66fd PXA: Drop CERF250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Mike Frysinger
8b0b0c59b5 add a git mailrc file for maintainers
This should make sending out e-mails to the right people easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-12-06 21:32:19 +01:00
Andy Fleming
1cdabc4bc7 miiphy: Note that miiphy_* API is deprecated
We want to move everything to phylib, and we definitely don't want
new drivers using the miiphy infrastructure.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-12-05 22:17:06 +01:00
Nobuhiro Iwamatsu
c67ce95433 sh: Add updating method of SPI ROM to README of sh7757lcr
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:21 +09:00
Shengzhou Liu
ae6b03fefc powerpc/p3060qds: Add board related support for P3060QDS platform
The P3060QDS is a Freescale reference board for the six-core P3060 SOC.

P3060QDS Board Overview:
 Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM for RCW
 Ethernet:
  - Eight Ethernet controllers (4x1G + 4x1G/2.5G)
  - Three VSC8641 PHYs on board (2xRGMII + 1xMII)
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
 PCIe: Two PCI Express 2.0 controllers/ports
 USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
 I2C:  Four I2C controllers
 UART: Supports two dUARTs up to 115200 bps for console
 RapidIO:  Two RapidIO, sRIO1 and sRIO2

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Stelian Pop
762e63754b Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-27 19:44:21 +01:00
Marek Vasut
b68d57c310 M28: Add doc/README.m28 documentation
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:58 +01:00
Wolfgang Denk
5721385b18 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
* 'master' of git://git.denx.de/u-boot-mpc83xx:
  powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
  powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
  mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
  mpc83xx: Cleanup usage of LBC constants
  mpc83xx: Cleanup usage of DDR constants
  mpc83xx: Cleanup usage of BAT constants
  mpc83xx: cosmetic: vme8349.h checkpatch compliance
  mpc83xx: cosmetic: ve8313.h checkpatch compliance
  mpc83xx: cosmetic: sbc8349.h checkpatch compliance
  mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
  mpc83xx: cosmetic: kmeter1.h checkpatch compliance
  mpc83xx: cosmetic: TQM834x.h checkpatch compliance
  mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
  mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
  mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
  mpc83xx: Fix ipic structure definition
  powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions
  cosmetic, powerpc, mpc83xx: checkpatch cleanup
  powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c
  mpc83xx: fix global timer structure definition
2011-11-08 07:44:52 +01:00
Jerry Huang
6be55ee225 powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-07 18:34:40 -06:00
Michael Jones
84d7a0171f OMAP3: mvblx: Initial support for mvBlueLYNX-X
Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04 13:54:33 -04:00
Heiko Schocher
4dd834906d arm, davinci: add cam_enc_4xx support
- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
  the RAM with the post memory test. If error
  is found, switch all LEDs on and halt system.
- SPI Flash
  Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Heiko Schocher
435199f380 arm, davinci: add support for new spl framework
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Heiko Schocher
18e8ff18fa spl: add option for adding post memory test to the SPL framework
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Simon Schwarz
3a0d60c504 SPL: Add DMA library
Adding a DMA library to the SPL. It is used if CONFIG_SPL_DMA_SUPPORT is
defined.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:34 +02:00
Simon Schwarz
4c4bb19d05 omap3: Add interface for omap3 DMA
Adds an interface to use the OMAP3 DMA.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:34 +02:00
Simon Glass
eea63e05d0 fdt: ARM: Add fdtcontroladdr to set device tree address in environment
This adds support for a new environment variable called 'fdtcontroladdr'. If
defined, the hex address is used as the address of the control fdt for U-Boot.

Note: I have not changed CONFIG_PRAM section as I already have an
outstanding patch on that.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:40:16 +02:00
Simon Glass
bbb0b128c3 fdt: Add support for embedded device tree (CONFIG_OF_EMBED)
This new option allows U-Boot to embed a binary device tree into its image
to allow run-time control of peripherals. This device tree is for U-Boot's
own use and is not necessarily the same one as is passed to the kernel.

The device tree compiler output should be placed in the $(obj)
rooted tree. Since $(OBJCOPY) insists on adding the path to the
generated symbol names, to ensure consistency it should be
invoked from the directory where the .dtb file is located and
given the input file name without the path.

This commit contains my entry for the ugliest Makefile / shell interaction
competition.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:38:59 +02:00
Anton staaf
46a6d51c82 cache: add ALLOC_CACHE_ALIGN_BUFFER macro
This macro is used to allocate cache line size aligned stack
buffers for use with DMA hardware.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Aneesh V <aneesh@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
2011-10-25 09:23:10 +02:00
Wolfgang Denk
e877fabeb9 MPC85xx: remove broken "mpq101" board
The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-10-23 17:00:47 +02:00
Joe Hershberger
b3f44c21ea common: cosmetic: CONFIG_BOOTFILE checkpatch compliance
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:21:35 +02:00
Macpaul Lin
afc1ce8288 doc/README: documents and readme for NDS32 arch
Documents and READMEs for NDS32 architecture.
It patch also provides usage of SoC AG101 and board ADP-AG101.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-10-22 00:54:45 +02:00
Simon Glass
744d9859a7 sandbox: Add architecture header files
This adds required header files for the sandbox architecture, and a basic
description of what sandbox is (README.sandbox).

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-17 22:45:50 +02:00
Jason Hobbs
06283a6401 Add pxe command
Add pxe command, which is intended to mimic PXELINUX functionality.
'pxe get' uses tftp to retrieve a file based on UUID, MAC address or IP
address. 'pxe boot' interprets the contents of PXELINUX config like file
to boot using a specific initrd, kernel and kernel command line.

This patch also adds a README.pxe file - see it for more details on the
pxe command.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:35 +02:00
Jason Hobbs
b41bc5a82d common, menu: use abortboot for menu timeout
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:33 +02:00
Jason Hobbs
b69bf52dfe Add generic, reusable menu code
This will be used first by the pxe code, but is intended to be
generic and reusable for other jobs in U-boot.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:33 +02:00
York Sun
6f5e1dc531 powerpc/8xxx: Add support for interactive DDR programming interface
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.

To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:

setenv ddr_interactive on

After reset, U-boot prompts before initializing DDR controllers
FSL DDR>

The available commands are
print      print SPD and intermediate computed data
reset      reboot machine
recompute  reload SPD and options to default and recompute regs
edit       modify spd, parameter, or option
compute    recompute registers from current next_step to end
next_step  shows current next_step
help       this message
go         program the memory controller and continue with u-boot

The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:53 -05:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Mike Frysinger
1285a2808a mkconfig: start deprecating Makefile config targets
Now that we've got boards.cfg and most people have converted over,
start warning people who have yet to so we can phase board configs
completely out of the Makefile.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:15 +02:00