Add a generic FIT generator script for RISC-V to generate images
containing U-Boot, OpenSBI FW_DYNAMIC firmware, and optionally one or
more device trees. The location of the OpenSBI firmware binary can be
specified with the OPENSBI environment variable. By default, it is
assumed to be "fw_dynamic.bin", located in the U-Boot top-level. Device
trees are passed as arguments to the generator script. A separate
configuration entry is created for each device tree.
The load addresses of U-Boot and OpenSBI are parsed from the U-Boot
configuration. They can be overwritten with the UBOOT_LOAD_ADDR and
OPENSBI_LOAD_ADDR environment variables.
The script is based on the i.MX (arch/arm/mach-imx/mkimage_fit_atf.sh)
and Allwinner sunxi (board/sunxi/mksunxi_fit_atf.sh) FIT generator
scripts.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
To support relocation of the stack and global data on RISC-V, the
secondary harts must be notified of the change using IPIs. We can reuse
the hart relocation code for this purpose. It uses global data to store
the new stack pointer and global data pointer for the secondary harts.
This means that we cannot update the global data pointer of the main
hart in spl_relocate_stack_gd(), because the secondary harts have not
yet been relocated at this point. It is updated after the secondary
harts have been notified.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
U-Boot SPL on the generic RISC-V CPU supports two boot flows, directly
jumping to the image and via OpenSBI firmware. In the first case, both
U-Boot SPL and proper must be compiled to run in the same privilege
mode. Using OpenSBI firmware, U-Boot SPL must be compiled for machine
mode and U-Boot proper for supervisor mode.
To be able to use SPL, boards have to provide a supported SPL boot
device.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
RISC-V OpenSBI is an open-source implementation of the RISC-V Supervisor
Binary Interface (SBI) specification. It is required by Linux and U-Boot
running in supervisor mode. This patch adds support for booting via the
OpenSBI FW_DYNAMIC firmware. It supports OpenSBI version 0.4 and higher.
In this configuration, U-Boot SPL starts in machine mode. After loading
OpenSBI and U-Boot proper, it will start OpenSBI. All necessary
parameters are generated by U-Boot SPL and are passed to OpenSBI. U-Boot
proper is started in supervisor mode by OpenSBI. Support for OpenSBI is
enabled with CONFIG_SPL_OPENSBI. An additional configuration entry,
CONFIG_SPL_OPENSBI_LOAD_ADDR, is used to specify the load address of the
OpenSBI firmware binary. It is not used directly in U-Boot and instead
is intended to make the value available to scripts such as FIT
configuration generators.
The header file include/opensbi.h is based on header files from the
OpenSBI project. They are recent, as of commit bae54f764570 ("firmware:
Add fw_dynamic firmware").
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
U-Boot SPL can be run in a different privilege mode from U-Boot proper.
Add new configuration entries for SPL to allow the run mode to be
configured independently of U-Boot proper.
Extend all uses of the CONFIG_RISCV_SMODE and CONFIG_RISCV_MMODE
configuration symbols to also cover the SPL equivalents. Ensure that
files compatible with only one privilege mode are not included in builds
targeting an incompatible privilege mode.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
As part of the SPL FIT boot flow, the device tree is appended to U-Boot
proper. The device tree is used to record information on the loadables
to make them available to the SPL framework and U-Boot proper. Depending
on the U-Boot device tree provider, the FIT image might not include a
device tree. Information on the loadables is missing in this case.
When booting via firmware bundled with the FIT image, U-Boot SPL loads
the firmware binary and U-Boot proper before starting the firmware. The
firmware, in turn, is responsible for starting U-Boot proper.
Information on the memory location of the U-Boot proper loadable must be
available to the SPL framework so that it can be passed to the firmware
binary. To support this use case when no device tree is found in the FIT
image, fall back to the U-Boot device tree in this situation.
At the same time, update the comment to remove the note that the
destination address must be aligned to ARCH_DMA_MINALIGN. Alignment is
only required as an intermediate step when reading external data. This
is automatically handled by spl_fit_append_fdt(). After reading the
external data, it is copied to the specified address, which does not
have to be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
When building a U-Boot FIT image, the device trees specified by the
board are unconditionally built for inclusion in the FIT image. However,
not all device tree providers, such as CONFIG_OF_PRIOR_STAGE, require a
device tree to be built and bundled with the U-Boot binary. They rely on
other mechanisms to provide the device tree to U-Boot. Compilation on
boards with these device tree providers fails, because they do not
specify a device tree.
Change the makefile rules to conditionally build the device trees if
CONFIG_OF_SEPARATE, CONFIG_OF_EMBED, or CONFIG_OF_HOSTFILE is selected
as device tree provider.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
The current preprocessor logic prevents CONFIG_OF_PRIOR_STAGE from being
used in U-Boot SPL. Change the logic to also make it available in U-Boot
SPL.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This was changed to 1 in commit 0717dde057, but a few months later,
commit 5f9411af37 swapped the order of eMMC and SD card by assigning
indexed aliases to `&sdhci` and `&sdmmc`.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Add signature)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some ChromeOS devices (atleast veyron speedy) have the first 8MiB of
the eMMC write protected and equipped with a dummy 'IGNOREME' GPT
header - instead of spewing error messages about it, just silently
try the backup GPT.
Note: this does not touch the gpt cmd writing/verifying functions,
those will still complain.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There were 3 copies of the same sequence, make it into a function.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We should use the shared helpers to setup the necessary parts
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
This is based off of Klaus Goger's work in 8adc9d
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We need to store all the ram related cap/map info back to register
for each channel after all the init has been done in case some of register
was reset during the process.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
By default, i2c input clock is platform clk / 2, but some of the
platform of i2c clock divider does not meet this kind of circumstance,
so alone to set default values for these platforms.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.
USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources
SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.
SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.
By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start
address of the flash sector containing the environment. It fixes
the issue that bootcmd is always set as default at bootup.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4
bit 5. enable this bit so that flexcan is enabled in LX2160ARDB.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
