Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
When switching the TQM8xxL modules to use the CFI flash driver,
support for the second flash bank was broken because the CFI driver
did not support dynamically sized banks. This gets fixed now.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On ADS5121 when booting linux the following errors are seen:
Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND
This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming. This patch
fixes this by being smarter about what to
fixup.
Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".
Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.
Signed-off-by: John Rigby <jrigby@freescale.com>
U-Boot allows for configurable prompt strings using the
CONFIG_AUTOBOOT_PROMPT resp. CONFIG_MENUPROMPT definitions. So far,
the assumption was that any such user defined problts would contain
exactly one "%d" format specifier. But some boards did not.
To allow for flexible boot prompts without adding too complex code we
now allow to specify the whole list of printf() arguments in the user
definition. This is powerful, but requires a responsible user who
really understands what he is doing, as he needs to know for exanple
which variables are available in the respective context.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tried fixing NAND support for the at91rm9200dk board; untested.
Disabled NAND support in the csb637 board config file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
- Relocate the location of U-Boot in the flash
- Save the environment in one sector of the flash memory
- MTD Support
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Due to increased space usage, U-Boot can no longer be stored in three sectors.
The current U-Boot use just over three flash sectors (197k), and U-Boot will
become corrupt after saving environment variables. This patch adds another 64k
to CFG_MONITOR_LEN.
Signed-off-by: Frank E. Svendsbøe <frank.svendsboe@gmail.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI
support, or without TSEC1 but with USB ULPI PHY support in addition.
With this patch user can specify desired USB PHY.
Also, it seems that we can't distinguish the two boards in software, so
user have to set `mpc8315erdb' environment variable to either 'tsec1'
(TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that
Linux will not probe for TSEC1.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
The L2_INIT_RAM option was unused, and recent changes to the TLB code
meant that the INIT_RAM TLBs weren't being cleared out. In order to reduce
the amount of mapped space attached to nothing, we change things so the TLBs
get cleared.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fake flash bank was generating errors for anyone who didn't have a
PromJET hooked up to the board. As that constitutes the vast majority of
users, we remove it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This was proposed by Paul Gortmaker in response to Wolfgang's comments on
similar #defines in sbc8560.h.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add in the default fdt settings and the typical EXTRA_ENV
settings as borrowed from the mpc8560ads. Fix a couple
of stale references to the mpc8560ads dating back to the
original clone/fork.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The existing config doesn't define CONFIG_HAS_ETH0, and so the
fdt support doesn't update the zeros in the dtb local-mac with
real data from the u-boot env. Since the existing config is
tailored to just two interfaces, get rid of the ETH2 definitions
at the same time.
Also don't include any end user specific data into the environment
by default -- things like MAC address, network parameters etc. need
to come from the end user.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The definitions for the TSEC have become out of date. There is no
longer any such options like "CONFIG_MPC85xx_TSEC1" or similar.
Update to match those of other boards, like the MPC8560ADS.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch cleans up the 440SPe PCIe register usage. Now only defines
from the include/asm-ppc/4xx_pcie.h are used.
Signed-off-by: Stefan Roese <sr@denx.de>
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for placing the RGMII bridge on the
PPC405EX(r) into MII/GMII mode and allows a board-specific
configuration to specify the bridge mode at compile-time.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch completes the preprocessor mneomics for the IBM DDR2 SDRAM
controller registers (MODT and INITPLR) used by the
PowerPC405EX(r). The MMODE and MEMODE registers are unified with their
peer values used for the INITPLR MR and EMR registers,
respectively. Finally, a spelling typo is correct (MANUEL to MANUAL).
With these mnemonics in place, the CFG_SDRAM0_* magic numbers for
Kilauea are replaced by equivalent mnemonics to make it easier to
compare and contrast other 405EX(r)-based boards (e.g. during board
bring-up).
Finally, unified the SDRAM controller register dump routine such that
it can be used across all processor variants that utilize the IBM DDR2
SDRAM controller core. It produces output of the form:
PPC4xx IBM DDR2 Register Dump:
...
SDRAM_MB0CF[40] = 0x00006701
...
which is '<mnemonic>[<DCR #>] = <value>'. The DCR number is included
since it is not uncommon that the DCR values in header files get mixed
up and it helps to validate, at a glance, they match what is printed
in the user manual.
Tested on:
AMCC Kilauea/Haleakala:
- NFS Linux Boot: PASSED
- NAND Linux Boot: PASSED
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ADS5121 Rev 3 board is now the default config
config targets are now
ads5121_config
Rev 3 board with
PCI
M41T62 on board RTC
512MB DRAM
ads5121_rev2_config
Rev 2 board with
No PCI
256MB DRAM
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Rigby <jrigby@freescale.com>
Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM.
To support such configurations, we "only" map the first 2GB via the TLB's. We
need some free virtual address space for the remaining peripherals like, SoC
devices, FLASH etc.
Note that ECC is currently not supported on configurations with more than 2GB
SDRAM. This is because we only map the first 2GB on such systems, and therefore
the ECC parity byte of the remaining area can't be written.
Signed-off-by: Stefan Roese <sr@denx.de>
ARM: Fix for incorrect version of patch applied when
adding support for the Lyrtech SFF-SDR board.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister, OpenSDR <philip@opensdr.com>
After we move the atmel_mci driver into drivers/mmc, we can't select
it with CONFIG_MMC anymore. Introduce a new symbol specifically for
this driver so that there's no ambiguity.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
