Commit Graph

7 Commits

Author SHA1 Message Date
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Jean-Jacques Hiblot
3e6ab7327f usb: dwc3: Kconfig: get rid of obsolete mode selection
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.

Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:17 +02:00
Tom Rini
f512851413 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-21 10:11:23 -04:00
Neil Armstrong
d0b1f72a04 configs: u200: enable support for USB Host & Gadget
Now the Amlogic G12A DT and drivers are present, enable full USB
on the U200 Reference Design board.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-05-31 10:09:41 +02:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Jerome Brunet
b050a30016 boards: meson: add g12a u200
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.

The board has the following specifications :
 - Amlogic S905D2 ARM Cortex-A53 quad-core SoC
 - XGB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module
 - MIPI DSI Connector
 - Audio HAT Connector
 - PCI-E M.2 Connector

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23 11:19:09 +02:00