Commit Graph

9286 Commits

Author SHA1 Message Date
Wolfgang Wegner
87d93a1ba2 move prototypes for gunzip() and zunzip() to common.h
Prototype for gunzip/zunzip was only in lib_generic/gunzip.c and thus
repeated in every file using it. This patch moves the prototypes to
common.h and removes all prototypes distributed anywhere else.

Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
2009-12-21 21:39:59 +01:00
Wolfgang Denk
f7767c7541 Merge branch 'master' of git://git.denx.de/u-boot-usb 2009-12-21 21:01:56 +01:00
Mahavir Jain
127e10842b usb: write command for RAW partition.
This patch implements write support to usb device with raw partition.
It will be useful for filesystem write support to usb device from
u-boot in future.

Tested with writing kernel image to raw usb disk & booting with usb
read command into ram.

[Note:  run usb part to get info about start sector & number of
sectors on a partition for usb write operation.]

Signed-off-by: Mahavir Jain <mjain@marvell.com>
2009-12-20 12:53:00 +01:00
Ajay Kumar Gupta
73c8640e93 omap3evm: musb: add USB config
Added USB host and device config for host (MSC, Keyboard) and
device (ACM) functionalities.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2009-12-20 12:53:00 +01:00
Tom Rix
ae4caf2fb5 OMAP3 USB Initialize twl4030 only if required
OMAP3EVM uses ISP1504 phy and so twl4030 related init is not required.

Submitted-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Tom Rix
2ec1abea43 OMAP3 zoom2 Use usbtty if the debug board is not connected.
The preferred serial output comes from the debug board.
When the debug board is disconnected, fall back on using
usbtty from the usb connector on the Zoom2 board.

This shows up as /dev/ttyACM0 in a linux host.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Tom Rix
6299487ef5 USBTTY make some function declarations easier to use.
Zoom2 needs to use these declarations and the include directory is a
better place from them than in the middle of the driver directory.
It did not make sense to create a new file for just a couple of
lines so they were appended to the serial.h

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Tom Rix
25374bfbf3 OMAP3 beagle Add usbtty configuration
The primary console of beagle is the serial header.

A secondary console is to use the usbtty.  The user can set this
manually by doing

setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv

usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Tom Rix
05be5a60e9 OMAP3 zoom1 Add usbtty configuration
The primary console of zoom1 is the serial out from the jumpers
accessed by removing the back panel.

A secondary console is to use the usbtty.  The user can set this
manually by doing

setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv

usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:50:53 +01:00
Tom Rix
f298e4b6dd OMAP3 Add usb device support
This change adds the usb device support for musb.

Omap3 platform support added at the same level as davinci.

The interface for usbtty to use the musb device support was added.

Verified on omap3 beagle, zoom1 and zoom2.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Tom Rix
bffbb2a86d TWL4030 Add usb PHY support
The twl4030 provides a PHY device for connecting a link device,
like musb, to physical connection.

This change adds the twl4030 usb registers and functions for
initializing the PHY as required by omap3.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Tom Rix
988365a204 USB add macros for debugging usb device setup.
When developing usb device features, it is useful to print out
common usb structures.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Tom Rix
8f8bd565f3 USB Consolidate descriptor definitions
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for

usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor

These are out right duplicates in usb.h

usb_device_descriptor
usb_string_descriptor

This one has extra unused elements

usb_endpoint_descriptor

	unsigned char	bRefresh
	unsigned char	bSynchAddress;

These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.

usb_config_descriptor
usb_interface_descriptor

The change is to consolidate the definition of the descriptors
to usbdescriptors.h.  The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.

So

usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface

For these, the common descriptor elements are accessed now
by an element 'desc'.

As an example

-	if (iface->bInterfaceClass != USB_CLASS_HUB)
+	if (iface->desc.bInterfaceClass != USB_CLASS_HUB)

This has been compile tested on MAKEALL arm, ppc and mips.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Wolfgang Denk
b6535daefd Merge branch 'next' of git://git.denx.de/u-boot-net 2009-12-17 22:59:27 +01:00
Li Yang
e5e4e705ce Update Makefile for tag generating
Get tag directories from the $(__LIB) and also generate tag for .S files.

Signed-off-by: Li Yang <leoli@freescale.com>
2009-12-17 22:57:54 +01:00
Kumar Gala
d02ffbf8d7 drivers/bios_emulator: Fix compile error in .depend not being generated
make -C drivers/bios_emulator/
make[2]: Entering directory
`drivers/bios_emulator'
In file included from atibios.c:49:
biosemui.h:47:21: error: biosemu.h: No such file or directory
...
x86emu/decode.c:40:28: error: x86emu/x86emui.h: No such file or directory
...

Due to lack of proper CPPFLAGS being passed to .depend generation rule

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-12-17 22:24:36 +01:00
Wolfgang Denk
bb3bcfa242 Merge branch 'next' of ../next 2009-12-15 23:38:34 +01:00
Wolfgang Denk
a200a7c04d Update CHANGELOG; prepare Prepare v2009.11
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-15 23:20:54 +01:00
Peter Tyser
f9476902b7 mpc85xx, mpc86xx: Fix gd->cpu pointer after relocation
The gd->cpu pointer is set to an address located in flash when the
probecpu() function is called while U-Boot is executing from flash.
This pointer needs to be updated to point to an address in RAM after
relocation has occurred otherwise Linux may not be able to boot due to
"fdt board" crashing if flash has been erased or changed.

This bug was introduced in commit
a0e2066f39.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reported-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Tested-by: Kumar Gala <galak@kernel.crashing.org>
Tested on MPC8527DS.
Tested by: Ed Swarthout <Ed.Swarthout@freescale.com>
2009-12-15 22:45:51 +01:00
Ben Warren
1ab70f6fff Net: Clean up LAN91C96 Support
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support.  This patch
finishes the job.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-14 16:42:03 -08:00
Peter Tyser
3363a34b9e MVBLUE: Remove CONFIG_CMD_IRQ
Neither the MVBLUE nor its underlying architecture implement the
do_irqinfo() function which is required when CONFIG_CMD_IRQ is defined.
This change fixes the following MVBLUE compiler error:

-> ./MAKEALL MVBLUE
Configuring for MVBLUE board...
common/libcommon.a(cmd_irq.o):(.u_boot_cmd+0x24): undefined reference to `do_irqinfo'
make: *** [u-boot] Error 1

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2009-12-14 21:31:17 +01:00
Detlev Zundel
18e8ad60ee imx27lite: Reenable MTD support on NOR flash.
The support for this was silently dropped by a configuration
split during the merge of the imx27lite board support in commit
864aa034f3 (cmd_mtdparts: Move to common
handling of FLASH devices via MTD layer).

Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-12-14 21:30:11 +01:00
Thomas Weber
076cd24cb4 net: dm9000x: fix debug output
commit 60f61e6d76 breaks compile with gcc by introducing __func__
instead of constant string "func" in the macro call but missed to change the macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:57:01 -08:00
John Ogness
c179a2896e fec_mxc: incomplete error handling
fec_init() will only allocate fec->base_ptr if it is non-NULL. But
the cleanup routine on error will free the pointer without setting
it to NULL. This means that a later call to fec_init() would result
in using an invalid pointer.

Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:55:15 -08:00
Reinhard Arlt
2ab4a4d095 net: e1000: Add support for the Intel 82546GB controller
This chip is equipped for example on the esd PMC-ETH2-GB board. So let's
add it to the list of supported chips to the e1000 driver.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:52:30 -08:00
Remy Bohmer
aafda38fb2 Add error codes/handling for TFTP-server
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Nishanth Menon
ac6b362a25 LAN91C96: Enable NET_MULTI LAN driver
This modification is NOT tested on any of the
platforms modified as I dont have them. please
help by testing+building+fixing

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Nishanth Menon
a1725999b8 TI OMAP3: SDP3430 FIX NET_MULTI Warning
Enable the NET MULTI option and remove build warning

Tested: SDP3430

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Nishanth Menon
b7ad4109da NET: LAN91C96 CONFIG_NET_MULTIify
Make the lan91c96 driver capable of CONFIG_NET_MULTI
to be clean for the new arch, add a a lil detect function
Most of the formatting change was done to keep checkpatch
silent, but a few functions and #if 0ed code which
does not make sense for NET_MULTI have been removed

Now, use the lan91c96_initialize() function to init the driver

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Mike Frysinger
6ac59c5518 net: pull CONFIG checks out of source and into makefile
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Stefan Roese
f4cfe42758 nand: Fix access to last block in NAND devices
Currently, the last block of NAND devices can't be accessed. This patch
fixes this issue by correcting the boundary checking (off-by-one error).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2009-12-11 13:11:57 -06:00
Peter Korsgaard
3b887ca8ce mpc83xx: boot time regression, move LCRR setup back to cpu_init_f
Commit c7190f02 (retain POR values of non-configured ACR, SPCR, SCCR,
and LCRR bitfields) moved the LCRR assignment to after relocation
to RAM because of the potential problem with changing the local bus
clock while executing from flash.

This change unfortunately adversely affects the boot time, as running
all code up to cpu_init_r can cause significant slowdown.

E.G. on a 8347 board a bootup time increase of ~600ms has been observed:

   0.020 CPU:   e300c1, MPC8347_PBGA_EA, Rev: 3.0 at 400 MHz, CSB: 266.667 MHz
   0.168 RS:    232
   0.172 I2C:   ready
   0.176 DRAM:  64 MB
   1.236 FLASH: 32 MB

Versus:

   0.016 CPU:   e300c1, MPC8347_PBGA_EA, Rev: 3.0 at 400 MHz, CSB: 266.667 MHz
   0.092 RS:    232
   0.092 I2C:   ready
   0.096 DRAM:  64 MB
   0.644 FLASH: 32 MB

So far no boards have needed the late LCRR setup, so simply revert it
for now - If it is needed at a later time, those boards can either do
their own final LCRR setup in board code (E.G. in board_early_init_r),
or we can introduce a CONFIG_SYS_LCRR_LATE config option to only do
the setup in cpu_init_r.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-12-09 11:40:52 -06:00
Heiko Schocher
4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Heiko Schocher
00b6d927ba 5xxx, fdt: move fdt_fixup_memory() to cpu.c file
u-boot updates, before starting Linux, the memory node in the
DTS. As this is a "standard" feature, move this functionality
to the cpu.c file for mpc5xxx and mpc512x processors.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:13:02 +01:00
Michal Simek
386118a896 microblaze: Correct ffs regression for Microblaze
We are using generic implementation of ffs. This should
be part of Simon's commit 0413cfecea

Here is warning message which this patch removes.

In file included from /tmp/u-boot-microblaze/include/common.h:38,
                 from cmd_mtdparts.c:87:
/tmp/u-boot-microblaze/include/linux/bitops.h:123:1: warning: "ffs" redefined
In file included from /tmp/u-boot-microblaze/include/linux/bitops.h:110,
                 from /tmp/u-boot-microblaze/include/common.h:38,
                 from cmd_mtdparts.c:87:
/tmp/u-boot-microblaze/include/asm/bitops.h:269:1:
warning: this is the location of the previous definition

Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-12-08 09:19:01 +01:00
Graeme Smecher
8fe7b29f98 microblaze: Stop stack clobbering in microblaze-generic.
A typo caused the stack and malloc regions to overlap, which prevented
mem_malloc_init() from returning. This commit makes the memory layout match
the example described in include/configs/microblaze-generic.h

Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-12-08 08:51:42 +01:00
Wolfgang Denk
35e3717772 Merge branch 'master' of ../work into next 2009-12-07 23:42:33 +01:00
Wolfgang Denk
0fc52948bd Update CHANGELOG, prepare -rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 23:14:13 +01:00
Peter Tyser
f2352877cb MAKEALL: Fix return value
Previously MAKEALL would always return a value of 0, even if 1 or more
boards did not compile.  This change causes MAKEALL to return 0 if all
boards were able to build, otherwise 1.

This change also requires changing the script interpreter from sh to
bash to support bash's PIPESTATUS variable.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-12-07 23:06:42 +01:00
Peter Tyser
fbc1c8f6f6 tools/mkimage: Remove duplicate line of code
Recent commits 1a99de2cb4 and
6a590c5f5f both fixed the same bug in the
same manner.  Unfortunately git was "smart" enough to merge both changes
which resulted in some duplicate code.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Reordered code and comment a bit.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 23:01:42 +01:00
Heiko Schocher
df002fa6b9 i2c: fix dangling comment in do_i2c_mw()
commit bd3784df94 deleted some unused
code in do_i2c_mw(), but missed to also remove the respective
commment. This patch fixes this.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-07 22:58:46 +01:00
Heiko Schocher
7cb5fc15f2 mpc52xx, manroland: add some commands
add the following commands for the manroland boards:

CONFIG_CMDLINE_EDITING
CONFIG_COMMAND_HISTORY
CONFIG_AUTO_COMPLETE

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-07 22:50:41 +01:00
Wolfgang Denk
206c00f26f Merge branch 'master' into next
Conflicts:
	lib_generic/zlib.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 22:47:17 +01:00
Stefan Roese
39ff7d5f4c POST: Remove duplicated post_hotkey_pressed() functions
This patch introduces a weak default function for post_hotkey_pressed(),
returning 0, for boards without hotkey support. The long-running tests
won't be started on those boards. This default function was implemented
in many board directories. By implementing this weak default we can
remove all those duplicate versions.

Boards with hotkey support, can override this weak default function
by defining one in their board specific code.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-12-07 22:44:31 +01:00
Heiko Schocher
f8450829f9 52xx, manroland: add fdt_fixup_memory() in ft_board_setup()
To update the real memory size in the memory node on the
uc101 and mucmc52 boards call fdt_fixup_memory() in
ft_board_setup().

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-07 22:39:38 +01:00
Daniel Hobi
0ec81db202 Fix computation in nand_util.c:get_len_incl_bad
Depending on offset, flash size and the number of bad blocks,
get_len_incl_bad may return a too small value which may lead to:

1) If there are no bad blocks, nand_{read,write}_skip_bad chooses the
bad block aware read/write code. This may hurt performance, but does
not have any adverse effects.

2) If there are bad blocks, the nand_{read,write}_skip_bad may choose
the bad block unaware read/write code (if len_incl_bad == *length)
which leads to corrupted data.

Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
2009-12-07 22:38:16 +01:00
Evan Samanas
aabb8cb081 nfs: NfsTimeout() updates
- NfsTimeout() does not correctly update the NFS timeout value which
  results in NfsTimeout() only being called once in certain situations.
  This can result in the 'nfs' command hanging indefinetly.  For
  example, the command:

    nfs 192.168.0.1:/home/user/file

  will not exit until ctrl-c is pressed if 192.168.0.1 does not have an
  NFS server running.

  This issue is resolved by reinitializting the NFS timeout value inside
  NfsTimeout() when a timeout occurs.

- Make the 'nfs' command print the 'T' character when a timeout occurs.
  Previously there was no indication that timeouts were occuring.

- Mimic the 'tftpboot' command and when a download fails print "Retry
  count exceeded; starting again", and restart the download taking the
  'netretry' environment variable into account.

Signed-off-by: Evan Samanas <esamanas@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Tested on TQM8xxL.

Tested by: Wolfgang Denk <wd@denx.de>

Tested on MPC8527DS.

Tested by: Ed Swarthout <Ed.Swarthout@freescale.com>
2009-12-07 22:35:47 +01:00
Peter Tyser
224c90d106 bootm: Fix help message's sub-command ordering
The help message for the 'bootm' command listed the 'cmdline' and 'bdt'
sub-commands in the wrong order which resulted in the error below when
following the 'help' command's instructions:

  "Trying to execute a command out of order"

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-12-07 22:12:49 +01:00
Robert P. J. Day
a93c92cdda help: Correct syntax of nandecc help output.
"nandecc" help output should not reproduce the command name, nor have
a trailing newline.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2009-12-07 22:06:51 +01:00
Mike Rapoport
c2fff331a3 smc911x: update SMC911X related configuration description
Since commit 736fead8fd "Convert SMC911X
Ethernet driver to CONFIG_NET_MULTI API" SMC911X configration options
are called CONFIG_SMC911X rather than CONFIG_DRIVER_SMC911X. Update
README to reflect that change.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
2009-12-07 22:05:43 +01:00