Commit Graph

4833 Commits

Author SHA1 Message Date
Tom Rini
84f24ac827 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-07-11 14:54:48 -04:00
Eric Nelson
e153333eeb i.MX6DL/S: add drive-strength back to pads DISP0_DAT2/DAT10
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.

These settings now match the i.MX6 Dual and Quad core versions.

Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-07-10 15:23:56 +02:00
Felipe Balbi
5ba95541b7 usb: phy: omap_usb_phy: implement usb_phy_power() for AM437x
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09 22:11:51 +02:00
Tom Rini
22692ec0fb Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-07-09 09:21:51 -04:00
Fabio Estevam
157f45da91 mx6: soc: Update the comments of set_ldo_voltage()
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces
set_ldo_voltage() function that can be used to set the voltages
of any of the three LDO regulators controlled by the PMU_REG_CORE register.

Prior to this commit there was a single set_vddsoc() which only configured the
VDDSOC regulator.

Update the comments to align with the new set_ldo_voltage() implementation.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-09 15:10:10 +02:00
Andre Renaud
2eb268f6fd MX6: Correct calculation of PLL_SYS
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do
the shift after the multiply to avoid rounding errors

Signed-off-by: Andre Renaud <andre@bluewatersys.com>
2014-07-09 14:55:30 +02:00
Alexey Ignatov
072b2d8872 kmake: include DTB section into u-boot.bin if CONFIG_OF_EMBED enabled
Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting
u-boot.bin, so u-boot was unable to find embedded DTB.
2014-07-07 19:47:24 -04:00
Masahiro Yamada
443a2ec57a blackfin, powerpc: remove redundant definitions of ARRAY_SIZE
Since ARRAY_SIZE macro is defined in include/common.h,
re-defining it in arch-specific files is redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
2014-07-07 19:47:12 -04:00
Vasili Galka
a91fd00175 blackfin: Add more dcache functions
Add invalidate_dcache_range() and flush_dcache_range() for the blackfin
architecture. Such functions already exist on this arch with different
names, so just forward the call.

This fixes the build of bf609-ezkit board as it uses
drivers/net/designware.c which requires the above functions.

Cc: Sonic Zhang <sonic.adi@gmail.com>, Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-07-07 19:47:11 -04:00
Vasili Galka
fa28179d2c m68k: Fix incorrect memory access on M5235
The csarX and cscrX registers in the fbcs_t struct are 16-bit for
CONFIG_M5235 and 32-bit wide otherwise. The code in cpu_init.c
accessed them always as 32-bit, effectively creating a wrong memory
access on M5235. Fixed that by choosing out_be16/out_be32 depending
on whether CONFIG_M5235 is defined or not.

Cc: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-07-07 19:47:08 -04:00
Vasili Galka
6b02d06feb m68k: Fix bug, "address of" operator was forgotten
in_be16() shall be passed a pointer to register and not its value. This
is clearly a typo resulting in a wrong memory access, so fix it.

Cc: Alison Wang <b18965@freescale.com>, Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-07-07 19:47:07 -04:00
Masahiro Yamada
98ad54beb5 mpc8xx: remove spc1920 board support
This board is old enough and has no maintainer.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-07 19:43:02 -04:00
Masahiro Yamada
03f9d7d174 mpc8xx: remove fads board support
These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-07 19:43:02 -04:00
Masahiro Yamada
c51c1c9af9 mpc8xx: remove netta, netta2, netphone board support
These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-07 19:43:02 -04:00
Masahiro Yamada
0657e46e28 mpc8xx: remove RPXlite_dw, quantum board support
These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-07 19:43:01 -04:00
Masahiro Yamada
dab0f7626e mpc8xx: remove qs850, qs860t board support
These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-07 19:43:01 -04:00
Cooper Jr., Franklin
8038b497e7 am43xx: Tune the system to avoid DSS underflows
* This is done by limiting the ARM's bandwidth and setting DSS priority in
  the EMIF controller to ensure underflows do not occur.
2014-07-07 19:42:34 -04:00
Franklin S. Cooper Jr
2c95211167 am43xx: Update EMIF DDR3 Configuration for AM43x GP
* Boot failures have been discovered due to a combination of routing issues and
  non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
  different timings are required for alpha, beta and production boards.

Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
2014-07-07 19:42:34 -04:00
Masahiro Yamada
a8b0f9b685 build: define CPU only when arch/${ARCH}/cpu/${CPU} exists
The directory arch/${ARCH}/cpu/${CPU} does not exist
in avr32, blackfin, microblaze, nios2, openrisc, sandbox, x86.

These architectures have only one CPU type.
Defining CPU should not be required for such architectures.

This commit allows cpu field (= the 3rd field of boards.cfg)
to be kept blank.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2014-07-07 19:42:34 -04:00
Jeroen Hofstee
878cae6b02 ARM: emif4: wait for CM_DLL_READYST to be set
The code intends for the CM_DLL_READYST to be set, but
actually polls till any bit is set since the logical
AND is used instead of the bitwise one is used. Fix it.

cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-07 19:42:33 -04:00
Tom Rini
6ee3d00d1d Merge branch 'master' of git://git.denx.de/u-boot-i2c 2014-07-07 10:10:52 -04:00
Chin Liang See
23f23f23d5 socfpga: Relocate arch common functions away from board
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2014-07-05 10:14:46 +02:00
Shaibal.Dutta
fe0d925299 arm: Fix armv8 compilation error
Fix following compilation error when CONFIG_ARM64 is defined

Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'

Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
2014-07-05 09:30:20 +02:00
Jeroen Hofstee
ed6c7f7f6e arm: spl: fix include guard
cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-05 09:28:21 +02:00
Chin Liang See
dc4d4aa14b socfpga: Adding Scan Manager driver
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-07-05 00:27:27 +02:00
Chin Liang See
05b884b5cd socfpga: Adding DesignWare watchdog support
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-07-05 00:24:18 +02:00
Sergey Kostanbaev
7237d22baa arm: ep9315: Return back Cirrus Logic EDB9315A board support
This patch returns back support for old ep93xx processors family

Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
2014-07-04 23:45:48 +02:00
Jeroen Hofstee
fcfddfd504 ARM: cache_v7: use __weak
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.

cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
2014-07-04 19:57:22 +02:00
York Sun
f749db3a75 ARMv8/ls2085a_emu: Add LS2085A emulator and simulator board support
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
  Two DDR controllers
  UART2 is used as the console
  IFC timing is tightened for speedy booting
  Support DDR3 and DDR4 as separated targets
  Management Complex (MC) is enabled
  Support for GIC 500 (based on GICv3 arch)

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-07-04 19:48:41 +02:00
J. German Rivera
b940ca64b2 armv8/fsl-lsch3: Add support to load and start MC Firmware
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.

Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
2014-07-03 08:40:58 +02:00
York Sun
2f78eae506 ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoC
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-07-03 08:40:51 +02:00
York Sun
22932ffc03 ARMv8: Adjust MMU setup
Make MMU function reusable. Platform code can setup its own MMU tables.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
2014-07-03 08:40:48 +02:00
J. German Rivera
0d031e046c Added 64-bit MMIO accessors for ARMv8
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.

Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
2014-07-03 08:40:31 +02:00
Darwin Rambo
261d27605c arm: Add support for semihosting for armv8 fastmodel targets.
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.

Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.

Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
2014-07-03 08:35:45 +02:00
Stephen Warren
68049a082b i2c: tegra: use repeated start for reads
I2C read transactions are typically implemented as follows:

START(write) address REPEATED_START(read) data... STOP

However, Tegra's I2C driver currently implements reads as follows:

START(write) address STOP START(read) data... STOP

This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:19 +02:00
Albert ARIBAUD
304f936aea Merge remote-tracking branch 'u-boot-samsung/master'
Conflicts:
	boards.cfg

Conflict was trivial between goni maintainer change and
lager_nor removal.
2014-07-01 20:52:51 +02:00
Albert ARIBAUD
019b57cc1d Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-07-01 15:48:25 +02:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Albert ARIBAUD
d6694aff56 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-06-30 23:00:34 +02:00
Stefano Babic
5d2ad2bc33 vf610: fix build due to missing sys_proto.h
commit 67a04ab3ab
fix the build for MX25. The same error
happens for VF610 SOC.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-25 12:48:06 +02:00
Albert ARIBAUD
01a3647abd Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-06-25 10:40:23 +02:00
Albert ARIBAUD
ed1d98d801 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-06-25 10:39:58 +02:00
Masahiro Yamada
1638d98052 sandbox: change local_irq_save() to macro
local_irq_save() should be a macro, not a function
because local_irq_save() saves flag to the given argument.

GCC is silent about this issue, but Clang warns:

In file included from lib/asm-offsets.c:15:
In file included from include/common.h:20:
In file included from include/linux/bitops.h:110:
arch/sandbox/include/asm/bitops.h:59:17:
 warning: variable 'flags' is uninitialized when used here
      [-Wuninitialized]
        local_irq_save(flags);
                       ^~~~~

That change causes another warning:

In file included from include/linux/bitops.h:110:0,
                 from include/common.h:20,
                 from lib/asm-offsets.c:15:
arch/sandbox/include/asm/bitops.h: In function ‘test_and_set_bit’:
arch/sandbox/include/asm/bitops.h:56:16: warning: unused variable ‘flags’ [-Wunused-variable]

So, flags should be set to __always_unused.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-23 15:37:24 -06:00
Stephen Warren
9c38c07008 sandbox: terminate os_dirent_ls() result list
Each node in the linked-list that os_dirent_ls() returns has its next
pointer set only when the next node is created. For the last node in the
list, there is no next node, so this never happens, and the next pointer
is never initialized. Explicitly initialize the next pointer so that it
isn't dangling. Without this, "sb ls" might crash.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-06-23 15:37:24 -06:00
Vasili Galka
dbb7234b2a x86: Enable 32-bit build using x86_64 multilib toolchain
Until now building the x86 arch boards required 32-bit toolchain. As
many x86_64 toolchains come with 32-bit support (multilib) that's a
good idea to enable build with such toolchains.

The change required was to specify the usage of 32-bit explicitly to
the compiler and the linker (-m32 and -m elf_i386 flags) and locate
the right libgcc path.

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-06-23 15:37:23 -06:00
Akshay Saraswat
8e4ab1d582 Exynos5420: Introduce support for the Peach-Pit board
While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit
line of devices, there could be other boards using the same chip, so a
common configuration file is being added (exynos5420.h) as well
as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi).

The peach board as declared in boards.cfg is a copy of smdk5420
declaration. The configuration files are similar, but define different
default device trees, console serial ports and prompts.

The device tree files for smdk5420 and peach-pit inherit from the same
common file.

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-23 08:45:44 +09:00
Akshay Saraswat
eacf46d340 Exynos5420: Let macros be used for exynos5420
Macros defined in exynos5_setup.h specific to SMDK5420
are required for Peach-Pit too. Hence, replacing
CONFIG_SMDK5420 with CONFIG_EXYNOS5420 to enable these
macros for all the boards based on Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-23 08:45:44 +09:00
Simon Glass
8946034a31 tegra: dts: Bring in GPIO bindings from linux
These files are taken from Linux 3.14.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-06-20 11:56:33 -06:00
Simon Glass
5957ac2a9f Makefile: Support include files for .dts files
Linux supports this, and if we are to have compatible device tree files,
U-Boot should also.

Avoid giving the device tree files access to U-Boot's include/ directory.
Only include/dt-bindings is accessible.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-06-20 11:55:03 -06:00
Simon Glass
42d3b29d9e sandbox: Support iotrace feature
Support the iotrace feature for sandbox, and enable it, using some dummy
I/O access methods.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-20 11:54:42 -06:00