Enabling saving variables to MMC(FAT), NAND, SPI based on primary bootmode.
Maybe that logic can be tuned for more complicated use cases and better
tested for different bootmodes.
Tested on zcu104 to SD(FAT) and JTAG(NOWHERE).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have name variable saved in BSS section when it
doesn't need to be really used. That's why remove static from variable
definition and use strdup() to duplicate string with exact size from malloc
area instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current algorithm used to get the silicon name is bit complicated and
hard to follow. Updated to use more straightforward mechanism based on
the Device ID code table (Table 1-2). The full IDCODE register is used
(except device revision bits [31:28]) to get the device name and IDCODE2
value is used for identifying the variant.
Additionally to make the algorithm bit more clear it also save some space
as the devices table is slightly bit smaller.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add MSCC header with delay definitions for VSC8531 and associated
family devices.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It was protected just for SPL_OS_BOOT but this function is only called when
SPL_ATF is enabled that's why change macro name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Value of shunt resistor for INA226s that monitor VCCINT and VCC_SOC power
rails are incorrect. This patch corrects those values.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
There is 2nd pca9548 mux on I2C1 bus that controls SFP0, SFP1, and QSFP1
ports. Channel 0 and 1 are connected to J287 connector for SFP0 & SFP1, and
channel 2 is connected to J288 connector for QSFP1.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add CONFIG_XILINX_UARTLITE config to versal/zynqmp defconfig to
enable uartlite driver support by default.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This endinness changes are taken from linux uartlite driver.
Reset TX fifo in control register and check TX fifo empty
flag in lower byte of the status register to detect if it
is a little endian system. Based on this check, program the
registers with le32 or be32 through out the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable required configs for using ubifs in uboot.
UBIFS testing procedure from u-boot:
Let's say we have two partitions in dt as below and want to format
partition1 "images" with ubifs.
partition@0 {
label = "boot";
reg = <0x0 0x1000000>;
};
partition@1 {
label = "images";
reg = <0x1000000 0x7000000>;
};
We will format the partition from linux and copy some files and access
from uboot later.
First thing, in linux config disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
this is required as ubifs expects min LEB size as 15*1024 bytes.
Use below commands in linux to format "images" partition with ubifs.
ubiformat /dev/mtd1
ubiattach /dev/ubi_ctrl -m 1
ubimkvol /dev/ubi0 -N images -m
mount -t ubifs ubi0:images /mnt
We can copy files to /mnt and unmount it.
To access this ubifs partition from uboot, run below commands.
(Don't forget to probe device before, e.g. sf probe 0 0 0)
setenv mtdids "nor0=nor0"
setenv mtdparts "mtdparts=nor0:16m(boot),112m(images)"
ubi part images
ubifsmount ubi0:images
make sure we match "mtdparts" to whatever is given in dt w.r.t partition
sizes.
"mtdparts" command will list the mtd partitions in u-boot.
Once ubifs is mounted, we can use "ubifsls" to list the files in that
partition and use "ubifsload <addr> <filename>" to load files from ubifs
partition to DDR.
Reading information about mtd layout from DT is not supported.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot on xilinx boards is checking one address where DTB can be placed as
the first location for DTB. Originally this code was developed for Versal
where QEMU was putting generated DTB for U-Boot to use.
The patch enables changing this address which is necessary for cases where
default address is pointing to location (DDR) which is not present. The
access to this location can cause exception.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is similar to ZynqMP u-boot feature wise that's why also enable
default option for ENV_FAT_DEVICE_AND_PART Kconfig entry.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
CONFIG_BLK needs to be enabled by default to allow U-Boot to
compile after a 'make pic32mzdask_defconfig'.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The GPIO pins used by the SDHCI controller need to be configured to
allow the interface to work.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
sunxi64 conversion to use binman
New 'no-map' property for reserved memory
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9qZDsRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZSngf/UHS8BWPy1cLHUBB1RlwH212qQu+zvome
yh9VjY9C6nC6CSQhZUuwMqk3HACcjSmXG8JP6UY7WnvYmuKGaYtpwvAk04llG5Da
5+srmmrMtAMsILtVS82je3aLzHoXFiGex0xmxGrkVvGY60HglMkEliQlFG3WnlS0
A0YRWhDuDMKTCg1FLimnFX2j7HjmigDZcUZ0MdhWSbxtvqPnK7y89FjPeMa25CWH
PxQ0vQXcWazoRqZcMCAx8fyq+Fi1htk/176LN6Y91Xhtfhufmx5GKtfYnfR24MY5
6p+cfE+Tfk8DwB0Hy9eWEjUwjFhOovYcopjynEXdn/lXBKi/hjMhXQ==
=n3yY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22sep20' of git://git.denx.de/u-boot-dm into next
binman enhancements for FIT
sunxi64 conversion to use binman
New 'no-map' property for reserved memory
When a message is written by a log driver (e.g. via the network stack) this
may result in the generation of further messages. We cannot allow these
additional messages to be emitted as this might result in an infinite
recursion.
Up to now only the syslog driver was safeguarded. We should safeguard all
log drivers instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OP-TEE reserved memory node must set property "no-map" to prevent
Linux kernel from mapping secure memory unless what non-secure world
speculative accesses of the CPU can violate the memory firmware
configuration.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add a test to verify that the no-map property is added in reserved-memory
node when fdtdec_add_reserved_memory() no-map parameter is set to true.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When an external blob is missing it can be quite confusing for the user.
Add a way to provide a help message that is shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add a new entry argument to the fit entry which allows selection of the
default configuration to use. This is the 'default' property in the
'configurations' node.
Update the Makefile to pass in the value of DEVICE_TREE or
CONFIG_DEFAULT_DEVICE_TREE to provide this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Explain that binman interprets these environment variables in the
"External tools" section to run target/host specific versions of the
tools, and add a new section on how to use CROSS_COMPILE to run the
tests on non-x86 machines.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch lets tools.Run() use host-specific versions with the
for_host keyword argument, based on the host-specific environment
variables (HOSTCC, HOSTOBJCOPY, HOSTSTRIP, etc.).
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, binman always runs the compile tools like cc, objcopy, strip,
etc. using their literal name. Instead, this patch makes it use the
target-specific versions by default, derived from the tool-specific
environment variables (CC, OBJCOPY, STRIP, etc.) or from the
CROSS_COMPILE environment variable.
For example, the u-boot-elf etype directly uses 'strip'. Trying to run
the tests with 'CROSS_COMPILE=i686-linux-gnu- binman test' on an arm64
host results in the '097_elf_strip.dts' test to fail as the arm64
version of 'strip' can't understand the format of the x86 ELF file.
This also adjusts some command.Output() calls that caused test errors or
failures to use the target versions of the tools they call. After this,
patch, an arm64 host can run all tests with no errors or failures using
a correct CROSS_COMPILE value.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These test files are currently "intended for use on x86 hosts", but most
of the tests using them can still pass when cross-compiled to x86 on an
arm64 host.
This patch enables non-x86 hosts to run the tests by specifying a
cross-compiler via CROSS_COMPILE. The list of variables it sets is taken
from the top-level Makefile. It would be possible to automatically set
an x86 cross-compiler with a few blocks like:
ifneq ($(shell i386-linux-gnu-gcc --version 2> /dev/null),)
CROSS_COMPILE = i386-linux-gnu-
endif
But it wouldn't propagate to the binman process calling this Makefile,
so it's better just raise an error and expect 'binman test' to be run
with a correct CROSS_COMPILE.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch makes buildman create linked working trees instead of clones
of the source repository, but keeps updating the older clones of the
repository that might already exist. These worktrees share "everything
except working directory specific files such as HEAD, index, etc." with
the source repository. See the git-worktree(1) manual page for more
information.
If git-worktree isn't available, silently falls back to cloning the
repository.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
