This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
To be able to test Dallas onewire protocol and one wire eeproms driver
and subsystem, add in sandbox defconfig the drivers' config.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)
usage example:
bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1
bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the Sandbox TPMv2 driver in all possible configurations.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This MC34708 PMIC is somewhat special - it used single transfers (R/W) with
3 bytes size - up till now U-Boot's PMICs only used 1 byte.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is no longer used on any supported platform in U-Boot and
there is no interest in maintaining it further from people that have
used it historically.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
c: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
When functions return an error it propagates up the stack to the point
where it is reported. Often the error code provides enough information
about the root cause of the error that this is obvious what went wrong.
However in some cases the error may be hard to trace. For example if a
driver uses several devices to perform an operation, it may not be
obvious which one failed.
Add a log_ret() macro to help with this. This can be used to wrap any
error-return value. The logging system will then output a log record when
the original error is generated, making it easy to trace the call stack
of the error.
This macro can significantly impact code size, so its use is controlled
by a Kconfig option, which is enabled for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable all logging features on sandbox so that the tests can be run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We cannot use sandbox memory at 0 since other things use memory at that
address. Move it up out of the way.
Note that the pre-console buffer is currently disabled with sandbox, but
this change will avoid confusion if it is manually enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The choice of "USB keyboard polling" cannot be optional as without
one mechanism being set, it just doesn't work. Set the default one
to CONFIG_SYS_USB_EVENT_POLL.
Fixes: ecad7051 ("configs: Migrate all of the existing USB symbols, except fastboot")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The CONFIG_BOOTSTAGE_USER_COUNT option is no-longer needed since we can now
support any number of user IDs. Also BOOTSTAGE_ID_COUNT is not needed now.
Drop these unused options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add unit tests for the 'gpt rename' and 'gpt swap' commands that
rely on the block device created by test/py/make_test_disk.py.
Add CONFIG_CMD_GPT_RENAME to the sandbox_defconfig. Remove the
testdisk.raw test device at the end of the tests.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_SF_TEST
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Convert this option and enable it in sandbox. Also correct a bug which
was introduced with the block-device driver model conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This converts the following to Kconfig:
CONFIG_CMD_PCI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This converts the following to Kconfig:
CONFIG_CMD_MTDPARTS_SPREAD
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Make this a bool not a string]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the pre-console buffer, displaying the model and post-relocation
console announce on sandbox. Also add a model name to the device tree.
This allows testing of these features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This updates sandbox to use a live device tree. This means that after
relocation (from board_init_r() onwards) it no-longer uses flat device
tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
