Commit Graph

121 Commits

Author SHA1 Message Date
Grzegorz Bernacki
7f19139389 [PPC440SPe] Improve PCIe configuration space access
- correct configuration space mapping
- correct bus numbering
- better access to config space

Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2007-09-07 18:20:23 +02:00
Gary Jennejohn
81b73dec16 ppc4xx: (Re-)Enable CONFIG_PCI_PNP on AMCC 440EPx Sequoia
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.

Here the details of this patch:

o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
  board-specific settings. As an example the sequoia board requires 0.
  Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
  PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
  CFG_PCI_CACHE_LINE_SIZE to 0.

Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-31 15:21:46 +02:00
Stefan Roese
02ba7022f6 ppc4xx: Update Sequoia/Rainier bootstrap command
As suggested by David Mitchell, here an update for the Sequoia/Rainier
bootstrap command.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-16 09:52:29 +02:00
Stefan Roese
34886bbea2 Merge with /home/stefan/git/u-boot/zeus 2007-08-14 15:00:42 +02:00
Stefan Roese
779e975117 ppc4xx: Add initial Zeus (PPC405EP) board support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-14 14:44:41 +02:00
Eugene OBrien
d2f6800662 ppc4xx: Update AMCC Bamboo 440EP support
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)

Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)

Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map

Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-31 10:24:56 +02:00
John Otken
d4024bb72d ppc4xx: Add support for AMCC 405EP Taihu board
Signed-off-by: John Otken <john@softadvances.com>
2007-07-26 17:49:11 +02:00
Stefan Roese
2a49fc17d0 ppc4xx: AMCC Luan uses the new boardspecific DDR2 controller setup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-16 10:01:38 +02:00
Stefan Roese
df3f17422a ppc4xx: Support for Yucca board with 440SPe Rev A added to 44x_spd_ddr2.c
The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-16 10:00:43 +02:00
Niklaus Giger
f780b83316 resubmit: ppc4xx: Remove sequoia/sequioa.h. Cleanup ppc440.h for PPC440EPX
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
2007-07-04 10:14:07 +02:00
Stefan Roese
e4feb7638c Merge with git://www.denx.de/git/u-boot.git 2007-06-25 20:20:30 +02:00
Stefan Roese
466fff1a7b ppc4xx: Add pci_pre_init() for 405 boards
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-25 15:57:39 +02:00
Wolfgang Denk
1636d1c852 Coding stylke cleanup; rebuild CHANGELOG 2007-06-22 23:59:00 +02:00
Igor Lisitsin
a11e06965e Extend POST support for PPC440
Added memory, CPU, UART, I2C and SPR POST tests for PPC440.

Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
2007-06-22 23:21:01 +02:00
Stefan Roese
b3f9ec86e3 ppc4xx: Add bootstrap command for AMCC Sequoia (440EPx) eval board
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 533 nor        ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand       ;to configure the board for 667MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 17:22:44 +02:00
Stefan Roese
df8a24cdd3 [ppc4xx] Fix problem with NAND booting on AMCC Acadia
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 16:42:31 +02:00
Stefan Roese
86ba99e341 [ppc4xx] Change board/amcc/acadia/cpr.c to pll.c
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 16:40:58 +02:00
Stefan Roese
c440bfe6d6 ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval board
This patch adds NAND booting support for the AMCC Acadia eval board.

Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.

I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 267 nor	;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand	;to configure the board for 267MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-06 11:42:13 +02:00
Stefan Roese
18d156eb37 ppc4xx: Add missing file for Bamboo NAND booting support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 16:18:17 +02:00
Stefan Roese
f3679aa13d Merge with /home/stefan/git/u-boot/bamboo-nand 2007-06-01 16:15:34 +02:00
Stefan Roese
155a96478a ppc4xx: Undo Sequoia patch for dynamic EBC speed support of 83MHz
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:58:19 +02:00
Stefan Roese
9d9096043e ppc4xx: Update Sequoia NAND booting support with ECC
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:29:04 +02:00
Stefan Roese
a471db07fb ppc4xx: Prepare Bamboo port for NAND booting support
This patch updates the "normal" Bamboo NOR booting port, so
that it is compatible with the coming soon NAND booting
Bamboo port.

It also enables the 2nd NAND flash on the Bamboo.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:19:29 +02:00
Stefan Roese
5d4a179013 ppc4xx: Update AMCC Acadia support for board revision 1.1
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.

Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-24 08:22:09 +02:00
Jeffrey Mann
ada4697d02 [PATCH] Run new sequoia boards with an EBC speed of 83MHz
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.

This allows for maximum clocking speeds  to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.

Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
2007-05-16 13:23:10 +02:00
Stefan Roese
f544ff6656 ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND booting
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-05 08:29:01 +02:00
Stefan Roese
8b39501d28 ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driver
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-29 14:13:01 +02:00
Stefan Roese
e673226ff9 ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROM
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-18 12:07:47 +02:00
Stefan Roese
a65c5768e5 ppc4xx: Change SysACE address on Katmai
With this new base address of the Xilinx SystemACE controller
the Linux driver will be easier to adapt, since it can now be
mapped via the "normal" ioremap() call.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-02 10:09:30 +02:00
Stefan Roese
0e7d4916af Merge with git://www.denx.de/git/u-boot.git 2007-03-31 13:44:12 +02:00
Stefan Roese
da6ebc1bc0 ppc4xx: Update Katmai bootstrap command
Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB
is selected.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31 13:16:23 +02:00
Stefan Roese
490e5730c6 ppc4xx: Fix "bootstrap" command for Katmai board
The board specific "bootstrap" command is now fixed and can
be used for the AMCC Katmai board to configure different
CPU/PLB/OPB frequencies.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-31 08:47:34 +02:00
Stefan Roese
e50b791b3f Merge with /home/stefan/git/u-boot/acadia 2007-03-24 15:59:23 +01:00
Stefan Roese
0d974d5297 [PATCH] Add 4xx GPIO functions
This patch adds some 4xx GPIO functions. It also moves some of the
common code and defines into a common 4xx GPIO header file.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24 15:57:09 +01:00
Stefan Roese
2db633658b [PATCH] Small Sequoia cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24 15:55:58 +01:00
Stefan Roese
3cb86f3e40 [PATCH] Clean up 40EZ/Acadia support
This patch cleans up all the open issue of the preliminary
Acadia support.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24 15:45:34 +01:00
Wolfgang Denk
2a8dfe0835 Code cleanup. Update CHANGELOG 2007-03-21 23:26:15 +01:00
Stefan Roese
fc1e45ce6e Merge with /home/stefan/git/u-boot/acadia 2007-03-21 14:38:25 +01:00
Stefan Roese
16c0cc1c82 [PATCH] Add AMCC Acadia (405EZ) eval board support
This patch adds support for the new AMCC Acadia eval board.

Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-21 13:39:57 +01:00
Stefan Roese
8423e5e31a [PATCH] Use dynamic SDRAM TLB setup on AMCC Ebony eval board
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-16 21:11:42 +01:00
Stefan Roese
992423ab43 ppc4xx: Fix file mode of sequoia.c
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08 23:00:08 +01:00
John Otken john@softadvances.com
8ce16f55c7 ppc4xx: Clear Sequoia/Rainier security engine reset bits
Signed-off-by: John Otken john@softadvances.com <john@softadvances.com>
2007-03-08 22:49:22 +01:00
Wolfgang Denk
35ded29fd9 Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xx 2007-03-08 11:38:58 +01:00
Stefan Roese
cd84528f20 Merge with /home/stefan/git/u-boot/yucca-ddr2 2007-03-08 10:32:45 +01:00
Stefan Roese
00cdb4ce5e [PATCH] Update AMCC Luan 440SP eval board support
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.

This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08 10:13:16 +01:00
Stefan Roese
2f5df47351 [PATCH] Update AMCC Yucca 440SPe eval board support
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08 10:10:18 +01:00
Stefan Roese
2721a68a9e ppc4xx: Small AMCC Katmai 440SPe update
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-08 10:07:18 +01:00
Wolfgang Denk
46270c2851 Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xx 2007-03-07 16:50:34 +01:00
Stefan Roese
fa1aef15bc [PATCH] Use dynamic SDRAM TLB setup on AMCC Ocotea eval board
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-07 16:43:00 +01:00
Stefan Roese
07b7b0037a [PATCH] Speed optimization of AMCC Sequoia/Rainier DDR2 setup
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.

For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-06 07:47:04 +01:00