This patch enables ethernet support for ls1012aqds.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Contains all the pfe header files.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
pfe_command provides command line support for several features that
support pfe, like starting or stopping the pfe, checking the health
of the processor engines and checking status of different units inside
pfe.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds PFE driver to U-Boot
Following are the main driver files:-
pfe_hw.c: provides low level helper functions to initialize PFE
internal processor engines and other hardware blocks
pfe_driver.c: provides initialization functions
and packet send and receive functions
pfe_eth.c: provides high level gemac initialization functions
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
pfe_mdio.c: provides functions to initialize phy and mdio.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.
drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
phydev->dev->name);
^~
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
After allocating plat the pointer is checked.
Afterwards name is allocated and not checked.
Add the missing check to avoid a possible NULL dereference.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Pine64+ uses a generic PHY driver, so flip it over to using the
Realtek PHY driver to actually apply the RTL8211e fix.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If we check an index against array bounds, we should do so before
accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix NOR, SD and QSPI fallback option in case of secure boot failure.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch makes it possible to verify the contents and location of an
OPTEE image in DRAM prior to handing off control to that image. If image
verification fails we won't try to boot any further.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Andrew F. Davis <afd@ti.com>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
This patch adds a new type IH_OS_TEE. This new OS type will be used for
chain-loading to Linux via a TEE.
With this patch in-place you can generate a bootable OPTEE image like this:
mkimage -A arm -T kernel -O tee -C none -d tee.bin uTee.optee
where "tee.bin" is the input binary prefixed with an OPTEE header and
uTee.optee is the output prefixed with a u-boot wrapper header.
This image type "-T kernel -O tee" is differentiated from the existing
IH_TYPE_TEE "-T tee" in that the IH_TYPE is installed by u-boot (flow
control returns to u-boot) whereas for the new IH_OS_TEE control passes to
the OPTEE firmware and the firmware chainloads onto Linux.
Andrew Davis gave the following ASCII diagram:
IH_OS_TEE: (mkimage -T kernel -O tee)
Non-Secure Secure
BootROM
|
-------------
|
v
SPL
|
v
U-Boot ------>
<----- OP-TEE
|
V
Linux
IH_TYPE_TEE: (mkimage -T tee)
Non-Secure Secure
BootROM
|
-------------
|
v
SPL ------->
<----- OP-TEE
|
v
U-Boot
|
V
Linux
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Andrew F. Davis <afd@ti.com>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Link: http://mrvan.github.io/optee-imx6ul
When encountering an error in OPTEE verification print out various details
of the OPTEE header to aid in further debugging of encountered errors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
This patch adds optee_verify_bootm_image() which will be subsequently used
to verify the parameters encoded in the OPTEE header match the memory
allocated to the OPTEE region, OPTEE header magic and version prior to
handing off control to the OPTEE image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
This patch adds optee_image_get_load_addr() a helper function used to
calculate the load-address of an OPTEE image based on the lower
entry-point address given in the OPTEE header.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Add a helper function for extracting the least significant 32 bits from the
OPTEE entry point address, which will be good enough to load OPTEE binaries
up to (2^32)-1 bytes.
We may need to extend this out later on but for now (2^32)-1 should be
fine.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
CONFIG_OPTEE_LOAD_ADDR is used to tell u-boot where to load the OPTEE
binary into memory prior to handing off control to OPTEE.
We need to pull this value out of u-boot in order to produce an IMX IVT/CSF
signed pair for the purposes of secure boot. The best way to do that is to
have CONFIG_OPTEE_LOAD_ADDR appear in u-boot.cfg.
Adding new CONFIG entires to u-boot should be kconfig driven so this patch
does just that.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
OPTEE is currently linked to a specific area of memory called the TrustZone
DRAM. This patch adds a CONFIG entry for the default address of TrustZone
DRAM that a board-port can over-ride. The region that U-Boot sets aside for
the OPTEE run-time should be verified before attempting to hand off to the
OPTEE run-time. Each board-port should carefully ensure that the TZDRAM
address specified in the OPTEE build and the TZDRAM address specified in
U-Boot match-up.
Further patches will use TZDRAM address with other defines and variables to
carry out a degree of automated verification in U-Boot prior to trying to
boot an OPTEE image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
