Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The MX23 has less channels for the APBH DMA, sligtly different register
layout and some bits in those registers are placed differently. Reflect
this in the driver. This patch fixes MMC/DMA issue on MX23.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
It is useful to be able to try a range of
possible phy addresses to connect.
Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.
This also fixes MX28 fec_mii_setspeed use on secondary ethernet port
This was found by inspection of the code and should be
checked on real hardware.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
The MX23 can only use two SSP ports.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The clock data are not used by the driver, drop them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Instead of storing the computed line length in a local variable, store
it in the global lcd_line_length variable to make sure the LCD subsystem
can properly draw content for the display resolution.
This probably wasn't noticed yet because the only board where LCD
support is currently enabled is Seaboard, which runs at a 1366x768
resolution. As it happens this is the maximum resolution supported and
also the default that is used to initialize the framebuffer before the
configuration from DT is available.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Previously, the call to draw_logo() was happening irrespective
of whether we have selected logo or LCD console.
With this patch we call draw_logo() only when CONFIG_CMD_BMP is selected.
This would even fix the following compilation warning:
exynos_fb.c: In function 'draw_logo':
exynos_fb.c:74:8: warning: variable 'addr' set but not used
[-Wunused-but-set-variable]
exynos_fb.c:73:9: warning: variable 'y' set but not used
[-Wunused-but-set-variable]
exynos_fb.c:73:6: warning: variable 'x' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove unused variable disp_info to fix the following compilation warning:
exynos_dp.c: In function 'exynos_init_dp':
exynos_dp.c:860:23: warning: variable 'disp_info' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch resolves the following build errors for I2C driver in
VCMA9:
In file included from s3c24x0_i2c.c:40:0:
s3c24x0_i2c.h:38:17: error: field 'id' has incomplete type
s3c24x0_i2c.c:70:39: error: 'CONFIG_MAX_I2C_NUM' undeclared here (not
in a function) s3c24x0_i2c.c:70:31: warning: 'i2c_bus' defined but
not used [-Wunused-variable] s3c24x0_i2c.c:72:12: warning:
'i2c_busses' defined but not used [-Wunused-variable]
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some platforms (e.g. IGEPv2 board) has a broken ns16550 UART that
does not set the TEMT bit when the transmitter is empty in SPL.
This makes U-Boot to hang while waiting for TEMT to be set.
Add a new option to avoid this:
CONFIG_SYS_NS16550_BROKEN_TEMT
16550 UART set the Transmitter Empty (TEMT) Bit when all output
has finished and the transmitter is totally empty. U-Boot waits
for this bit to be set to initialize the serial console. On some
broken platforms this bit is not set in SPL making U-Boot to
hang while waiting for TEMT. Define this option to avoid it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Not only Spansion supports the Persistent Protection Bits (PPB) locking.
Other devices like the Micron JS28F512M29EWx also support this type
of locking/unlocking. Detection of support is done in the same way as
done for the Spansion chips - via the 0x49 CFI word.
This patch enables this PPB protection mechanism for all AMD type
(AMD commandset) chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Patch 66863b05 [cfi_flash: add support for Spansion flash PPB sector
protection] introduced the PPB (Persistent Protection Bit) locking for
Spansion chips. But right now the sector protection status (locked vs
unlocked) is set to unlocked for all sectors upon bootup. The real
sector protection status is ignored.
This patch now reads the current sector protection status and uses
it for these AMD/Spansion flash chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Consolidate manufacturer matching into the function manufact_match()
and use it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Add support for SST 4KB sector granularity.
Many recent SST flashes, i.e. SST39VF3201B and similar of this family
are declared CFI-conformant from SST. They support CFI query, but implement
2 different sector sizes in the same memory: a 64KB sector (they call it
"block", std AMD erase cmd=0x30), and a 4KB sector (they call it "sector",
erase cmd=0x50). Also, CFI query on these chips, reading from address 0x2dh
of cfi query struct, detects a number of secotrs for the 4KB granularity
(flinfo shows it).
For all other aspects, they are CFI compliant, so, as Linux do, i think
it's a good idea to handle these chips in the CFI driver, with a fixup
to allow 4KB granularity, as should be expected, instead of 64KB.
Signed-off-by: Angelo Dureghello <sysamfw@gmail.com>
Signed-off-by: Stefan Rose <sr@denx.de>
Currently, exynos FIMD driver is being used to support only TIZEN LOGOs.
In order to get LCD console, we need to enable half word swap feature
of FIMD and use 16 BPP.
LCD console and proprietary Logo cannot be used simultaneously.
We use "logo_on" field inside vidinfo_t structure to decide whether
user wants Logo or Console.
Define CONFIG_CMD_BMP and make logo_on = 1 to get Logo on screen.
Use logo_on = 0 to get output console on LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
lcd_set_flush_dcache(1) function is called from exynos_fb.c configuration file
to enable lcd_sync function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Adding fdt support to ehci-exynos in order to parse
register base addresses from the device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support to the SPI driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support to the codec.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support to the sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Functions added to get the I2C bus number and reset I2C bus using
FDT node.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
All esdhc variants we know should support high capacity MMC cards,
so let's add MMC_MODE_HC host_caps unconditionally to support those
MMC cards (capacity > 2 GB).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
Well, not terminating the list causes very interesting crashes.
As in changing the vendor & product ID crashes. Fun.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
SH7752 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marvell 88E1118R has different uid then 88E1118.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Andy Fleming <afleming@freescale.com>
CC: Zang Roy-R61911 <tie-fei.zang@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
In e1000e driver, Rx descriptor queue is used such that hardware can add only
one descriptor at a time. So the WTHRESH granularity in RXDCTL should be set
to single descriptor. This would ensure that every time controller fills a Rx
descriptor, it is flushed to host memory. Earlier this granularity was in
cache line units i.e 2 descriptors. This leads to controller always waiting
for 2 descriptors before flushing them out. But since not more than one Rx BD
is actually available , the accumulation condition never gets hit.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
It could happen (1 out of 100 times) that NAND did not start up correctly after
warm rebooting, so we end up with various failures or DMA timed out due to a
stalled BCH. When resetting BCH together with GPMI, the issue could not be
observed anymore (after 10000+ reboots). We probably need the consistent state
already before sending commands to NAND. This behaviour was observed in barebox
and kernel, so I assume it affects U-Boot as well. I chose to keep the extra
reset for BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
There are three couple (hcnt/lcnt) of registers for each
speed (SS/FS/HS). The driver needs to set the proper couple
of regs according to what speed we are setting.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In the newer versions of designware i2c IP there is the possibility
of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically
requires the s/w to generate the stop bit condition directly, as
the h/w will not automatically generate it when TX_FIFO is empty.
To avoid generation of an extra 0x0 byte sent as data, the
IC_STOP command must be sent along with the last IC_CMD.
This patch always writes bit[9] of ic_data_cmd even in the
older versions, assuming that it is a noop there.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch modifies the S3C i2c driver to support both Exynos4 and Exynos5
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same
way. This fixes the following error on OMAP5:
OMAP5430 EVM # mmc rescan
timed out in wait_for_bb: I2C_STAT=1410
twl6035: could not turn on LDO9.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The I2C block reset configures the I2C bus speed to strange value.
Read the I2C speed from the block before reseting the block and
restore it afterwards, so the I2C operates correctly. This issue
can be replicated by doing unsuccessful I2C transfer, after such
transfer finishes, the I2C block clock speed is misconfigured.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
According to FSL, the value in the TIMING2 register shall be 0x00300030
instead of what's written in the datasheet. This new value correlates
with older STMP36xx datasheet. Issues were detected in Linux when this
register was misconfigured, so write this correct value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver
to avoid duplication of code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch implements the setup and retrieval functions for the I2C
bus speed on the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch pulls out the I2C speed setup from the i2c_init() call
and implements the bus configuration lookup table with register
values that needs to be programmed into the I2C IP to run at
particular speed.
This patch is a first step towards implementing run-time I2C bus
speed configuration for the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Some functions in the MXC i2c driver were not static, fix this by
making them so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Moved the pmic_max77686.c max77686_pmic.h to drivers/power
and made required changes accordingly
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We handle i2c_write return code and complain in case of error. We propagate the
error, too, to allow better handling at the upper level in the future.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
We add a return code to wait_for_bb() to be able to report errors to the
callers properly. We in turn handle this new error code in i2c_read, i2c_write
and i2c_probe.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
Added posted writes (read after writes) to effect the
change immediately for channel confiuration and channel
enable register
Disable the channel to purge receieve data in TX_ONLY
mode transfer otherwise rx data will get affected by
the next immediate RX_ONLY mode transfer
Wait for the EOT bit to be set after last byte has been
loaded to TX shift register in the the TX_ONLY mode.This
ensures TX data has been completely shifted out
Disable the channel in RX_ONLY mode before reading the
last data from RXX register to prevent the SPI slave
to transmit next word
Signed-off-by: Ajoy Kumar Das <akdas75@yahoo.in>
Cc: Tom Rini <trini@ti.com>
Cc: jacopo mondi <j.mondi@voltaelectronics.com>
AM33XX with BCH8 can't work with nand_spl_simple correctly
because custom read_page implementation is required for proper
syndrome generation.
This simple driver mostly duplicates nand_spl_simple but has
nand_read_page changed to suit our needs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds support for BCH8 error correction code to omap_gpmc
driver. We use GPMC to generate codes/syndromes but we need ELM to find
error locations from given syndrome.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
[ilya: merge it with omap_gpmc driver, some fixes and cleanup]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The at91sam9m10g45 also support WDRBT bit, add support for it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
If the pl011 is connected to another device which has hardware
flow-control on, characters are never received by the pl011.
Asserting RTS when flow-control is off will have no effect.
This is in line with how Linux behaves.
Signed-off-by: Joshua Housh <joshua.housh@calxeda.com>
Tested-by: Marek Vasut <marex@denx.de>
This command will start erasing at memory address zero
if there is not a valid framebuffer address that was found
during video_init().
This is a common case with Chrome OS devices in normal mode
when we do not execute the video option rom in coreboot.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We can generally trust the ICH to have GPIO Bank 0 (the first 32 pins) in the
same place across all versions. This change adds two more banks, for up to
96 GPIOS.
BUT:
- Not all chipsets have the same number of GPIOs
- Not all chipsets have the same number of GPIO banks
- Not all chipsets put the additional banks at the same offset from GPIOBASE
- There so many chipset variants that it's pretty much impossible to support
them all, or even keep track of the new ones.
So, although this adds suppport for the additional banks that seem to work
for the particular variants of CougarPoint Mobile chipsets that we've tried,
there's no chance it will support everything Intel produces. Good luck.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement <asm-generic/gpio.h> functions for Intel ICH6 and later.
Only GPIOs 0-31 are handled by this code.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is useful to allow to observe messages generated by
coreboot and u-boot until present. In particular it is handy when
u-boot is instrumented to fall through into console mode on startup
errors.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch builds upon the recently introduced CBMEM console
feature of coreboot.
CBMEM console uses a memry area allocated by coreboot to store
the console output. The memory area has a certain structure,
which allows to determine where the buffer is, the buffer size
and the location of the pointer in the buffer. This allows
different phases of the firmware (rom based coreboot, ram based
coreboot, u-boot after relocation with this change) to keep
adding text to the same buffer.
Note that this patch introduces a new console driver and adds the
driver to the list of drivers to be used for console output, i.e.
it engages only after u-boot relocates. Usiong CBMEM console for
capturing the pre-relocation console output will be done under a
separate change.
>From Linux, run the cbmem.py utility (which is a part of the coreboot
package) to see the output, e.g.:
vvvvvvvvvvvvvvvvv
SCSI: AHCI 0001.0300 32 slots 6 ports ? Gbps 0xf impl SATA mode
flags: 64bit ilck stag led pmp pio
...
Magic signature found
Kernel command line: "cros_secure quiet loglevel=1 console=tty2...
^^^^^^^^^^^^^^^^^
Note that the entire u-boot output fits into the buffer only if
the coreboot log level is reduced from the most verbose. Ether
the buffer size will have to be increased, or the coreboot
verbosity permanently reduced.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
On kzm9g board (rmobile SoC), autoboot fails if serial console cable is not
connected. When serial cable is not connected, serial error occurs and
some garbage comes in data register.
sh_serial_tstc() in serial_sh.c does not check error status and misunderstand
there is some input data. It is the reason that autoboot fails.
This patch adds checking error status in sh_serial_tstc().
This patch is based on v2013.01-rc1 tag of u-boot master git.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.
Signed-off-by: Yuanquan Chen <B41889@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
At some point, a confusion arose about the use of the bit
definitions in host_caps for bus widths, and the value
in ext_csd. By coincidence, a simple shift could convert
between one and the other:
MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0
MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1
MMC_MODE_8BIT = 0x200, EXT_CSD_BUS_WIDTH_8 = 2
However, as host_caps is a bitmask of supported things,
there is not, in fact, a one-to-one correspondence. host_caps
is capable of containing MODE_4BIT | MODE_8BIT, so nonsensical
things were happening where we would try to set the bus width
to 12.
The new code clarifies the very different namespaces:
host_caps/card_caps = bitmask (MMC_MODE_*)
ext CSD fields are just an index (EXT_CSD_BUS_WIDTH_*)
mmc->bus_width integer number of bits (1, 4, 8)
We create arrays to map between the namespaces, like in Linux.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tegra's MMC driver does DMA, and hence needs cache-aligned buffers. In
some cases (e.g. user load commands) this cannot be guaranteed by callers
of the MMC APIs. To solve this, modify the Tegra MMC driver to use the
new bounce_buffer_*() APIs.
Note: Ideally, all U-Boot code will always provide address- and size-
aligned buffers, so a bounce buffer will only ever be needed for user-
supplied buffers (e.g. load commands). Ensuring this removes the need
for performance-sucking bounce buffer cache management and memcpy()s.
The one known exception at present is the SCR buffer in sd_change_freq(),
which is only 8 bytes long. Solving this requires enhancing struct
mmc_data to know the difference between buffer size and transferred data
size, or forcing all callers of mmc_send_cmd() to have allocated buffers
using ALLOC_CACHE_ALIGN_BUFFER(), which while true in this case, is not
enforced in any way at present, and so cannot be assumed by the core MMC
code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The current bouncebuf API requires all parameters to be passed to both
bounce_buffer_start() and bounce_buffer_stop(). Modify the bouncebuf
start function to accept a state structure as a parameter, and only
require that state struct to be passed to the stop function. This
simplifies usage of the bounce buffer by clients.
Don't modify the data pointer, but rather store the temporary buffer in
this state struct. The bouncebuf code ensures that client code can
always use a single buffer pointer in the state structure, irrespective
of whether a bounce buffer actually had to be allocated.
Move cache management logic into the bounce buffer code, so that each
client doesn't have to duplicate this. I believe there's no need to
invalidate the buffer before a DMA operation, since flushing the cache
should prevent any write-backs.
Update the MXS MMC driver for this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Bring in the code from Linux kernel.
Added to Linux kernel by:
commit e08c1694d9e2138204f2b79b73f0f159074ce2f5
Author: Andres Salomon <dilinger@queued.net>
Date: Fri Jul 4 10:00:03 2008 -0700
Some HW balks when writing both voltage setting and power up at the same
time to SDHCI_POWER_CONTROL register.
Signed-off-by: Rommel G Custodio <sessyargc@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
v2: fix attribution and SOB
Signed-off-by: Andy Fleming <afleming@freescale.com>
The interpretation of the data returned by the MMC_CMD_ALL_SEND_CID
command was incorrect with respect to the JEDEC Standard No. 84-A441.
This change makes the interpretation correct with respect to the
defined fields of the CID register.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND Flash is erased by blocks, not by pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
This patch cleans up nand_util.c:
- Fix tabs.
- Fix typos.
- Remove space character before opening parenthesis in function calls.
- Fix comments.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).
This is the same as a5ff4f102937a3492bca4a9ff0c341d78813414c in Linux
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[scottwood@freescale.com: fix fsl_ifc_sram_init prototype]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Document parameters used for specifying the NAND image to be loaded.
Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only
nand_spl_simple.c, not the entire nand directory. The word "simple" is
there for a reason. :-)
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: updated for makefile changes earlier in patchset
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic
ns16550 output code without pulling in things not needed by the SPL.
This previously only worked with non-MULTI configs. Recently MULTI was
made mandatory, and MIN_FUNCTIONS fails like this:
drivers/serial/libserial.o: In function `calc_divisor.clone.0':
serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq'
drivers/serial/libserial.o: In function `_serial_getc':
(.text._serial_getc+0x30): undefined reference to `NS16550_getc'
drivers/serial/libserial.o: In function `_serial_tstc':
(.text._serial_tstc+0x30): undefined reference to `NS16550_tstc'
drivers/serial/libserial.o: In function `_serial_setbrg':
(.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit'
make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1
make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2
With MIN_FUNCTIONS we don't need anything from this file, so don't build
it. The conditional needs to be in the file itself rather than the
makefile, because the config symbols are only imported to the makefiles
once, not separately for the SPL phase of the build.
Signed-off-by: Scott Wood <scottwood@freescale.com>
By commit c7e3b2b5, this was chanded to support multiple controllers.
But this has missing of parenthesis. This commit fix it.
-----
r8a66597-hcd.c: In function ‘usb_lowlevel_init’:
r8a66597-hcd.c:911:52: error: expected declaration specifiers before ‘)’
token
r8a66597-hcd.c:935:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or‘__attribute__’ before ‘{’ token
r8a66597-hcd.c:939:1: error: expected ‘{’ at end of input
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Lucas Stach <dev@lynxeye.de>
Some variables are initialized with a value defined by macro.
This was changed to use the macro directly. And the variable not to
use deleted it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Backend driver for MUSB OTG controllers found on TI AM35x.
It seems that on AM35X interrupt status registers can be updated
_before_ core registers. As we don't use true interrupts in U-Boot
and poll interrupt status registers instead this can result in
interrupt handler being called with non-updated core registers.
This confuses the code and result in hanged transfers.
Add a small delay in am35x_interrupt as a workaround.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Existing U-Boot musb driver has no support for the new gadget framework
and also seems to have other limitations. As gadget framework is ported
from Linux it seems pretty natural to port musb gadget driver as well.
This driver supports both host and peripheral modes.
This is not a replacement for current musb driver (at least now) as
there are still some consumers of the old UDC interface.
No DMA operation support included, CONFIG_MUSB_PIO_ONLY should be
defined.
Virtual root hub device is not implemented.
Known problems: with no devices connected usb_lowlevel_start() fails.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
If a board has all 8 data lines routed, the SD/MMC controller can still
operate in 4-bit (or presumably even 1-bit) mode. Adjust Tegra's MMC
driver to report the 4-bit capability even for 8-bit slots.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for CONSOLE_MUX to tegra-kbc driver. This requires
adding a flag to struct keyb to know the driver has already been
initialized so if we try to initialize it again we can just return
success. Also call into iomux_doenv() from drv_keyboard_init to
re-evaluate the stdin string.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for selecting the required cache mode for the LCD:
off, write-through or write-back.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This driver supports driving a single LCD and providing a U-Boot console
on it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Measuring the spi clock line on a scope shows a 'glitch' during the reset of the
spi.
Fix this by toggling only the MXC_CSPICTRL_EN bit, so that the clock line becomes
always stable.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
In decode_cs() function the polarity of the chip select must be taken into
account.
Also, for the case of low active chip select, the CS was activated too early.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A custom board_ehci_hcd_init() may be unneeded, so add a weak default
implementation doing nothing.
By the way, use simple __weak from linux/compiler.h for
board_ehci_hcd_postinit() instead of weak alias with full attribute.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like
MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT,
not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Clean up ehci-mxc:
- Remove useless #if's.
- Fix identation.
- Issue a #error if used with an unsupported platform.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>