This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.
cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Make MMU function reusable. Platform code can setup its own MMU tables.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
local_irq_save() should be a macro, not a function
because local_irq_save() saves flag to the given argument.
GCC is silent about this issue, but Clang warns:
In file included from lib/asm-offsets.c:15:
In file included from include/common.h:20:
In file included from include/linux/bitops.h:110:
arch/sandbox/include/asm/bitops.h:59:17:
warning: variable 'flags' is uninitialized when used here
[-Wuninitialized]
local_irq_save(flags);
^~~~~
That change causes another warning:
In file included from include/linux/bitops.h:110:0,
from include/common.h:20,
from lib/asm-offsets.c:15:
arch/sandbox/include/asm/bitops.h: In function ‘test_and_set_bit’:
arch/sandbox/include/asm/bitops.h:56:16: warning: unused variable ‘flags’ [-Wunused-variable]
So, flags should be set to __always_unused.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Each node in the linked-list that os_dirent_ls() returns has its next
pointer set only when the next node is created. For the last node in the
list, there is no next node, so this never happens, and the next pointer
is never initialized. Explicitly initialize the next pointer so that it
isn't dangling. Without this, "sb ls" might crash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Until now building the x86 arch boards required 32-bit toolchain. As
many x86_64 toolchains come with 32-bit support (multilib) that's a
good idea to enable build with such toolchains.
The change required was to specify the usage of 32-bit explicitly to
the compiler and the linker (-m32 and -m elf_i386 flags) and locate
the right libgcc path.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit
line of devices, there could be other boards using the same chip, so a
common configuration file is being added (exynos5420.h) as well
as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi).
The peach board as declared in boards.cfg is a copy of smdk5420
declaration. The configuration files are similar, but define different
default device trees, console serial ports and prompts.
The device tree files for smdk5420 and peach-pit inherit from the same
common file.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Macros defined in exynos5_setup.h specific to SMDK5420
are required for Peach-Pit too. Hence, replacing
CONFIG_SMDK5420 with CONFIG_EXYNOS5420 to enable these
macros for all the boards based on Exynos5420.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Linux supports this, and if we are to have compatible device tree files,
U-Boot should also.
Avoid giving the device tree files access to U-Boot's include/ directory.
Only include/dt-bindings is accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
gpmc timeout is disabled and the reset counter
is set to 0. However, if later a driver activates
the timeout setting the reset to a valid value,
the old reset value with zero is still valid
for the first access. In fact, the timeout block
loads the reset counter after a successful access.
Found on a am335x board with a FPGA connected
to the GPMC bus together with the NAND.
When the FPGA driver in kernel activates
the timeout, the system hangs at the first access
by the NAND driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set
for GPMC on chip select #0---size is 0. In this case, the GPMC
configuration should be reset but not enabled. Enabling causes the
Gumstix DuoVero board to hang when entering Linux.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
[trini: Switch to testing base as GPMC_SIZE_256M is 0x0]
Signed-off-by: Tom Rini <trini@ti.com>
The calling code seems a bit in doubt about the return
value of fdtdec_lookup_phandle. Since it returns a negative
value on error (and fdt_node_offset_by_phandle as well),
check for that.
cc: Wei Ni <wni@nvidia.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This flag does not compile on m68k since 2003 (8bde7f7) when a
required "cmd_bedbug.h" header was removed. Eleven years passed,
lets clean up a little...
Signed-off-by: Vasili Galka <vvv444@gmail.com>
After all, we have realized "force" argument is completely
useless. fdt_initrd() was always called with force = 1.
We should always want to do the same thing
(set appropriate value to the property)
even if the property already exists.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
According to:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0
ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b
newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:
i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison
With this change the secure boot status is correctly displayed
Signed-off-by: Stefano Babic <sbabic@denx.de>
mx6 reference manual incorrectly states that the DEVICE_TYPE field of
IOMUXC_GPR12 register should be configured as '0010' for setting the PCI
controller in RC mode. The correct value should be '0100' instead.
This also aligns with the same value used in the mx6 pci kernel driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit 41623c91 moved exception handlers to ".vectores" section
but it missed to adjust Zynq linker script.
Zynq boards hang up after relocation because "_start" symbol
does not point to the correct address and gd->relocaddr gets insane.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For at91 armv7 SoC (SAMA5D3x), only LCD and macb used DMA.
Now as the lcd and macb driver already support dcache. So we can
enable dcache now.
Also we can enable icache without any problem.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Unfortunately the avr32 cache implementation has another API than the one
described in common.h. Migrate the flush/invalidate dcache functions to the
common API to be usable in device drivers.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Josh Wu <josh.wu@atmel.com>
Sometimes Read DQ and DQS are not in phase. Since, this
phase shift differs from board to board, we need to
calibrate it at DRAM init phase, that's read DQ calibration.
This patch adds SW Read DQ calibration routine to compensate
this skew.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
when CLKM is running. If we stop CLKM when sampling it the glitches
all go away, so we'll do that as per Samsung suggestion.
We also check the "is it locked" bits of PHY_CON13 and loop until they
show the the value sampled actually represents a locked value. It
doesn't appear that the glitching and "is it locked" are related, but
it seems wise to wait until the PHY tells us the value is good before
we use it. In practice we will not loop more than a couple times (and
usually won't loop at all).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch intends to remove all code which enables hardware read
leveling. All characterization environments may not cope up with
h/w read leveling enabled, so we must disable this.
Also, disabling h/w read leveling improves the MIF LVcc value
(LVcc value is the value at which DDR will fail to work properly).
Improving LVcc means we have enough voltage margin for MIF.
When h/w leveling is enabled, we have almost zero volatge margin.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Passing fewer arguments is better and mem_iv_size is never
used. Let's keep only one argument and make it cleaner.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mkconfig links ${objtree}/include/asm/proc/ to
${srctree}/arch/${arch}/include/asm/proc-armv/. This seems to be a
remnant from the past. Ever since its introduction in 2003 it is used
only in ARM build and always links to same place, so let's simplify
the code, remove it and reference directly where needed.
Successful MAKEALL for ARM and PowerPC verified on Linux.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Most of the warnings seem to be related to using 'int' for size_t. Change
this and fix up the remaining warnings and problems. For bootm, the warning
was masked by others, and there is an actual bug in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
run_command() returns 0 for success, 1 for failure. Fix places which
assume that failure is indicated by a negative return code.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined.
This speeds up the Beaglebone Black boot considerable.
(Tested only on Beaglebone Black with SD card boot)
Signed-off-by: Simon Glass <sjg@chromium.org>
The symbol "_start" is defined twice in arch/arm/lib/vectors.S:
around line 48 and line 54.
If CONFIG_SYS_DV_NOR_BOOT_CFG is defined (as on calimain board),
build fails:
arch/arm/lib/vectors.S: Assembler messages:
arch/arm/lib/vectors.S:54: Error: symbol `_start' is already defined
make[1]: *** [arch/arm/lib/vectors.o] Error 1
make: *** [arch/arm/lib] Error 2
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Currently cntvoff_el2 is initialised with an arbitrary bag of bits
derived from the initial value of cnthctl_el2 on the current CPU. This is
somewhat odd and problematic as some of these bits are UNKNOWN at reset
and may differ across CPUs (which may cause an OS at EL1 to observe time
going backwards across CPUs).
This patch instead initialises cntvoff_el2 with xzr, giving the register
a consistent value of zero on all CPUs.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Tom Rini <trini@ti.com>
Acked-by: David.Feng <fenghua@phytium.com.cn>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Similar to OMAP4/5 we need to scale the voltage up prior to changing the
clock frequencies up higher. Add a similar hook to start with.
Signed-off-by: Tom Rini <trini@ti.com>
For usage of timer6 within B&R we need this defines to enable clock
modules and clk-source.
Also the 'Timer register bits' are expanded.
By the way we add defines for all timers within AM335x SoC.
Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
After enabling a module, SW has to wait on IDLEST bit
until it is Fully functional. This wait is missing for UART module
and there is a immediate access of UART registers after this. So there
is a chance of hang on this module( This can happen when we are running
from MPU SRAM). So waiting for IDLEST bit.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.
Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared. When SPL booting, this is handled by setting gd
to point to SRAM in s_init. However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.
Signed-off-by: Tom Rini <trini@ti.com>
We have two contexts for booting these platforms. One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads. The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL. In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.
In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus). In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.
Signed-off-by: Tom Rini <trini@ti.com>
The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices. As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.
Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.
Signed-off-by: Pekon Gupta <pekon@ti.com>
THe mx25 arch does not have a sys_proto.h file.
Instead of creating a dummy file, the file
is not included for this SOC.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The IMX6QUAD/DUAL have SATA, but the IMX6SOLO/DL do not. Return
instead of configuring the SATA clock and GPR13 registers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory-mapped structures for MMDC iomux and configuration. Note that whi
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux
registers differ. This requires two sets of structures.
Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration registers that can be used to
configure the MMDC dynamically.
We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add comment block for the imx_ddr_size function and remove the extra unused
fields from struct esd_mmdc_regs which are also not common between IMX53 and
IMX6.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add a common spl.c file to support boot device functions needed for SPL
such as detecting the boot device.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.
But many of them just define BOOT_DEVICE_* macros.
Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.
So they should not be archtecture specific, but be described as
a simpile enumeration.
This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.
With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
Remove the common infrastructure of nand_spl and
clean-up the code inside ifdef(CONFIG_NAND_U_BOOT)..endif.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Because cmd_mkimage is used in various subdirectories,
it seems reasonable to define it in scripts/Makefile.lib.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.
This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.
This workaround is valid for B4, T4 and T2 platforms, so
added in their config.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.
Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.
- add support for serdes protocols: 0x1b, 0x50, 0x5e,
0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
t2080qds and t2080rdb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The relocation code can now relocate from anywhere to
the RAM.
The old code assumed that the binary was copied to the RAM
by some PBL and then it just relocated the .text section
from the loaded address to the linked address.
Now, it first checks if vectors are somewhere else than the
linked address. If yes, there are copied to address 0 (or
to the exception vector base address if register EVBAR is
present).
Then, the .text section is relocated from its current location
to the RAM.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
The OpenRISC architecture specification v1.0 defines
new SPR registers. This patch adds registers definition
for group 0 and update bit definitions for the CPU
configuration register.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
The build fails if a non-generic ARM board is compiled
with CONFIG_OF_EMBED=y.
The correct symbol name for embedded FDT is not __dtb_db_begin,
but __dtb_dt_begin. (A typo introduced by commit 6ab6b2af)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/gadget support. This allows the user to type e.g.
"ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
implementing the USB Mass Storage protocol, and expose MMC device 0
that way.
This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This enables relocation of initrd to the end of available DDR before Linux
kernel start-up as it is done in other architectures.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Setting ps_hold ought to be one of the first things we do when we
first boot up. If we wait until the main u-boot runs we won't set it
in time and the PMIC may power us back off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This code seems unnecessarily complex. We really just need to check the
global_data. Now that is it all in one place, and not arch-specific, this
is pretty easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is quite a tight deadline in enabling PSHOLD, less than a second.
In some cases (e.g. with USB download), U-Boot takes longer than that
to load, so the board powers off before U-Boot starts.
Add a call in SPL to enable PSHOLD.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that the GPIO numbering series has been applied, we can use the correct
GPIO for the EC interrupt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
