The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D4 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D3 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To be able to test Dallas onewire protocol and one wire eeproms driver
and subsystem, add in sandbox defconfig the drivers' config.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZuJG
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
Only add CONFIG_DISPLAY to defconfig because CONFIG_I2C_EDID
is automatically selected by CONFIG_DISPLAY
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable CONFIG_OF_BOARD_SETUP as it is needed for Beaglebone
black to overwrite the Ethernet phy address present in DT
in case the phy latches on to a different address.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds a defconfig for sama5d27_som1_ek board to get environment from
uSD. The defconfig is made from sama5d27_som1_ek_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
uSD. The environment is expected to be found in uSD's FAT partition.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
CONFIG_BOOTARGS can be set using Kconfig, so we no longer need it
in the config files.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
This adds a defconfig for sama5d2_xplained board to get environment from
eMMC. The defconfig is made from sama5d2_xplained_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
eMMC. The environment is expected to be found in eMMC's FAT
partition.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Enable config USB relative flags in order to enable USB
EHCI, DWC2 gadget, download and mass_storage support.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
We should run the EFI selftest on both a 32bit and a 64bit ARM platform on
Travis to catch possible errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Unset CONFIG_EFI_UNICODE_CAPITALIZATION on boards with tough size
restrictions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the pci-aardvark driver in defconfig for Turris Mox and also
enable the pci command.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The dtb should be embedded in the u-boot-spl image so that
the CONFIG_SPL_TARGET of spl/u-boot-spl.hex includes it.
This also affects the main u-boot image, so adjust
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to u-boot.img which now
also includes the dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Due the changes in previous commits, we need to resync the defconfig
to reduce noise in next commits.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The 'bmode' command is helpful for switching the boot media.
In the case of pico-imx6ul there are two possible boot media:
eMMC or USB.
To boot from eMMC:
=> bmode emmc
To boot from USB (via Serial Download Protocol):
=> bmode usb
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx6ul U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc2-00130-g0881835-dirty
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx6ul to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_MMC now available, this patch enables DM_MMC for the
omapl138_lcdk in U-Boot and keeps the older style for SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OF_CONTROL and OF_PLATDATA are not really useful without DM.
This patch supports DM_SPL, but it requires manual references
both Serial and MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
At least for now, CONFIG_BLK is working, but this variant of
the da850evm doesn't need/support SPL so it's OK to enable it
here.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling
more options again.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables DM_SERIAL for the pandora board. Verified that
the default kernel can still be booted with this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Change the configured serial console index to reflect that it is the
first physical UART, reorder some defconfig lines and move some
environment configuration from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Activate the serial rx buffer.
Prepare console MUX activation with vidconsole, and avoid console
performance issue (missing character for copy-paste).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert the codes and configurations to enable DM drivers in u-boot for
modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI
This patch does not change SPL, so it still uses non-DM driver for
UART, GPIO and SD/MMC.
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
beagleboard x15 is the first supported platform variant of am57xx
in AOSP (android open source project) now.
changing board name to stay in consistent with aosp target name.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Switch the Arria10 from ad-hoc hardcoded timer to timer framework
and the DW APB timer driver. This allows the A10 to extract timer
information, like timer rate, from clock framework and thus DT
instead of having it hardcoded in U-Boot configuration files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)
usage example:
bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1
bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
A20 OLinuXino Micro eMMC board has emmc with mmc2 slot
so use proper dts, sun7i-a20-olinuxino-micro-emmc.dts
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The SPL space is limited. In order to try to enable DM in SPL,
we need more space. When combined wtih TINY_PRINTF, this reduces
the size of SPL by 6.5k
Original:
text data bss dec hex filename
20760 1216 80 22056 5628 spl/u-boot-spl
Tiny Printf
text data bss dec hex filename
17947 1216 80 19243 4b2b spl/u-boot-spl
Malloc Simple + Tiny Printf
text data bss dec hex filename
15187 176 28 15391 3c1f spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL space is limited. In order to try to enable DM in SPL,
we need more space. This reduces the size of SPL by ~2.7K
before:
text data bss dec hex filename
20760 1216 80 22056 5628 spl/u-boot-spl
after:
text data bss dec hex filename
17947 1216 80 19243 4b2b spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
Since using DM_I2C_COMPAT throws a warning during compilation,
and it isn't really needed any longer, so this patch removes
this feature and shrinks the code a bit.
from:
text data bss dec hex filename
343326 13388 123448 480162 753a2 u-boot
to:
text data bss dec hex filename
342924 13380 123440 479744 75200 u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
After creating CONS_INDEX and migrating a bunch of boards to it,
there are a bunch of defined references to CONFIG_SERIALx which
are not referenced in any C code or #ifdef, so they can now be
removed
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_TWL4030_LED
CONFIG_TWL4030_INPUT
This also removes dead references to:
CONFIG_TWL4030_KEYPAD
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate boards which set bootlimit in the environment to Kconfig.
We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting
if we migrated it.
display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME,
but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to
set bootlimit= in display5_factory_defconfig. This is okay because the
display5_factory_defconfig doesn't need to have it set, as it is only
meant to prepare the board in the factory.
Environment changes for all modified configs as seen from buildman:
boards.cfg is up to date. Nothing to do.
Summary of 3 commits for 32 boards (8 threads, 1 job per thread)
01: Merge git://git.denx.de/u-boot-x86
arm: + draco etamin rastaban pxm2 display5 thuban rut
02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit
03: Migrate bootlimit to Kconfig
- display5_factory: bootlimit=3
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable DM ethernet framework on Arria10, so that the designware GMAC
can be probed from DT as it should be.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
This commit enables CONFIG_BLK and removes USB_STORAGE which is awaiting
proper implementation for current U-Boot interfaces. Additionally the
console selection is now handled by Kconfig and no longer needs to be in
the config header. CONFIG_SYS_MALLOC_F_LEN=0x2000 was added to sync with
other boards. CONFIG_SPL_BLK and CONFIG_SPL_DM_MMC are disabled because
they currently do not allow the OMAP3-EVM (OMAP34XX) to actually boot.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
1. Add FIT support for DB410c defconfig.
2. Don't overwrite bootargs (they're already
defined in Linux device tree for DB410c.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Remove CONFIG_CMD_CACHE from include/configs/stm32f746-disco.h
and enable it in stm32f746-disco_defconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
"default" lines in Kconfig are processed in order, the first hit will
stop considering subsequent lines. In the case of the DRAM_ODT_EN symbol
that means that everything following the first two lines will never be
checked:
------------
config DRAM_ODT_EN
bool "sunxi dram odt enable"
default n if !MACH_SUN8I_A23
default y if MACH_SUN8I_A23
default y if MACH_SUN8I_R40
default y if MACH_SUN50I
------------
Assuming that the "default y" for the A64 and the R40 were a deliberate
choice, fix the Kconfig stanza to take this into account.
Also remove the now redundant lines from the respective defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: droped 'default n' on original change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # A64, R40
Tested-by: Chen-Yu Tsai <wens@csie.org> # A23
For these boards, the GPMC timings are more determined by
processor speed/type than the NAND/PoP memory. This code
is never invoked, so disable the config option, so it doesn't
take the time to compile it in.
Signed-off-by: Adam Ford <aford173@gmail.com>
The console index for SPL should be 1 not 3 in order to see text during
SPL.
Fixes: 6f6b7cfa89 ("Convert all of CONFIG_CONS_INDEX to Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This platform has been marked as orphan since June of 2016 and should
have been removed some time ago. Do so now.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that there is DM support in the RTC_MV driver update board configs
to use it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig. It will be just for Zynq arch and to do
will be for all other archs.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit enables support for DW_MMC running with driver model.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Exynos5422 is solely using DW MMC IP block to support eMMC/SD devices,
hence the SDHCI code doesn't need to be compiled it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CONFIG_BLK config flag becomes mandatory, enable it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Banana Pi M2 Ultra and M2 Berry are very similar boards. SATA can be
enabled exactly the same as for M2 Ultra introduced in
commit daa8b75a55 ("sunxi: enable SATA on Banana Pi M2 Ultra").
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
AXS10x boards have n25q512 spi flash IC, so add corresponding
nodes to device tree and enaple corresponding options in
defconfig.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With the pending requirement for CONFIG_BLK, this patch removes
the USB_STORAGE option which assumes that DM_USB is enabled, but isn't
yet available for the omap2340 musb glue among other issues. Once
the USB issues are resolved, a future patch can enable them again.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Move CONFIG_SPI_FLASH_SPANSION, CONFIG_SPI_FLASH, to defconfig.
Also disable disable 4K erase size option.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
4K erase size is used only in case of hydrid mode which is not
supported on any NXP platform with flash "s25fs512s".
Supported mode is uniform sector, with erase size 256kiB.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_SPL_FSL_LS_PPA is needed only in case of falcon boot
Support for this is not present in PPA currently, so
removing the default option from defconfig
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
