AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Existing U-Boot musb driver has no support for the new gadget framework
and also seems to have other limitations. As gadget framework is ported
from Linux it seems pretty natural to port musb gadget driver as well.
This driver supports both host and peripheral modes.
This is not a replacement for current musb driver (at least now) as
there are still some consumers of the old UDC interface.
No DMA operation support included, CONFIG_MUSB_PIO_ONLY should be
defined.
Virtual root hub device is not implemented.
Known problems: with no devices connected usb_lowlevel_start() fails.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Check for scancodes for arrow keys and map them to ^F/^B, ^N/^P.
Control characters are used instead of ANSI sequence because the
queueing code in usb_kbd doesn't handle the data increase when one
keypress generates 3 keycodes. The real fix is to convert this driver
to use the input subsystem and queue, but this allows arrow keys to
work until this driver is converted.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Enable USB keyboard for seaboard and ventana
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Move environment settings for stdin/stdout/stderr to
tegra-common-post.h and generate them automaticaly based on input
device selection.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Change usb_kbd driver to obey alignment requirements for USB DMA on
the buffer used for data transfer. This is necessary for
architectures that enable dcache and enable USB DMA.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
CONFIG_EHCI_DCACHE was removed by commit b8adb12
"USB: Drop cache flush bloat in EHCI-HCD". Remove the defines from
the boards configs as well.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Marek Vasut <marex@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Tom Rini <trini@ti.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Thierry Reding <thierry.reding@avionic-design.de>
cc: Tom Warren <twarren@nvidia.com>
cc: Stephen Warren <swarren@nvidia.com>
cc: Stefano Babic <sbabic@denx.de>
The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
If a board does not enable CSPI, there is no need to show the CSPI clock
frequency as part of the 'clock' command.
Reported-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Measuring the spi clock line on a scope shows a 'glitch' during the reset of the
spi.
Fix this by toggling only the MXC_CSPICTRL_EN bit, so that the clock line becomes
always stable.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
In decode_cs() function the polarity of the chip select must be taken into
account.
Also, for the case of low active chip select, the CS was activated too early.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A custom board_ehci_hcd_init() may be unneeded, so add a weak default
implementation doing nothing.
By the way, use simple __weak from linux/compiler.h for
board_ehci_hcd_postinit() instead of weak alias with full attribute.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like
MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT,
not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Clean up ehci-mxc:
- Remove useless #if's.
- Fix identation.
- Issue a #error if used with an unsupported platform.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
ehci-fsl.h so that all MXC SoCs can use them.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The inclusion of LCD patch into mx53loco breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video
related stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds time measurement and throughput calculation for
all supported load commands.
The output of ext2load changes from
---8<---
1830666 bytes read
--->8---
to
---8<---
1830666 bytes read in 237 ms (7.4 MiB/s)
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
[agust: rebased and revised commit log]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
the upcoming sunxi (allwinner a10/a13) platform enables zfs
by default, and using linaro's hf -msoft-float makes the build
fail because this u64 division.
Signed-off-by: Alejandro Mery <amery@geeks.cl>
Acked-by: Stefan Roese <sr@denx.de>
if a board uses the vcxk driver option CONFIG_SYS_VCXK_DOUBLEBUFFERD,
compilier shows warnings. This patch will fix it.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
