To group all dm timer drivers together, move tsc timer to
drivers/timer directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have converted all x86 boards to use driver model timer,
remove these legacy timer codes in the tsc driver.
Note this also removes the TSC_CALIBRATION_BYPASS Kconfig option,
as it is not needed with driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present bootstage will try to read the timer very early after relocation.
When driver model is used to provide the timer, we cannot read it until
driver model is ready. Correct this by adding a separate stage for the
post-relocation bootstage init.
This fixes booting on chromebook_link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Replace __attribute__((no_instrument_function)) with notrace from
<linux/compiler.h>.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is not referenced anywhere. Remove it, as well as
tsc_base_kclocks and tsc_prev in the global data.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix 'Reomve' typo:
Signed-off-by: Simon Glass <sjg@chromium.org>
There are timers with a 64-bit counter value but current timer
uclass driver assumes a 32-bit one. Modify timer_get_count()
to ask timer driver to always return a 64-bit counter value,
and provide an inline helper function timer_conv_64() to handle
the 32-bit/64-bit conversion automatically.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use device tree to pass the clock frequency of the timer
instead of hardcoded in the driver codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since we have timer uclass to get clock frequency for us, remove
the custom version in the altera timer driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Every timer device needs to have a valid clock frequency and it
can be specified in the device tree. Use pre_probe() to get this
in the timer uclass driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
This changes 'Timer' to 'timer' at several places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
To make saic redirect code sharing with other SoCs, move the
saic redirect code from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/atmel_sfr.c
Move ATMEL_SFR_AICREDIR_KEY definition to sama5d4.h, because each
SoC has its own value.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make matrix initialization code sharing with others,
use the matrix slave id macros, instead of hard-coding.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Remove the security peripheral select code, keep the default value
in these registers, that is, the peripheral address space is
configured as "Secured" access, it is suitable for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
On processor reset, the matrix write protection is disabled,
so no need to disable/enable write protection when writing
the matrix registers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make the matrix initialization code sharing with other SoCs,
move it from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/matrix.c
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The early MMU table doesn't enable all addresses. Unused addresses
are marked as invalid, as introduced by commit 9979922. An entry
was missing for NAND flash space, causing nand boot failure.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
As the environment variables "serial#" and "ethaddr" need to be
overwriten by the users, CONFIG_ENV_OVERWRITE is defined to disable
the write protection. Anybody can change or delete these parameters.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMACx to PHY mapping for SGMII is mentioned as QSGMII.
So fix typo in README for QSGMII rise card.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Change from ls2085aqds to ls2080aqds]
Reviewed-by: York Sun <yorksun@freescale.com>
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel
fails to access the device tree blob on boot. The reason is that u-boot
relocates the device tree blob into high memory when booting the kernel
and the kernel is unable to access the blob.
To avoid this issue, fdt_high is set to the value of 0xffffffff. The
device tree blob will not get relocated and is still in low memory to
make it accessible to the kernel.
For the same reason, initrd_high is set to the value of 0xffffffff too.
This patch is to update fdt_high and initrd_high for LS1021AQDS board.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When one core is released, other cores may not have valid entry
address. Those cores are trapped by "wfe" and wait for further
instruction. When their address is set, they need to be kicked
off by "sev".
Signed-off-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The global_data pointer (gd) has been set earlier in crt0_64.S.
So there's no need to assign it again. Remove gdata since it is going
away in U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
MC 0.7.1.2 enforces limitation i.e.: "Packets may be corrupted
in several combinations of buffer size and frame offsets.
Workaround: Use buffers that are of size that is a multiple of 256, and
frame offset that is a multiple of 256"
Updating the DPNI Eth driver to comply with the restriction.
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following debug information in the driver
- Get various DPNI counter values
- Get link status of DPNI objects
- Get information of both ends of connection (DPMAC - DPNI)
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per current implementation of DPAA2 ethernet driver DPNI is used as
net device. DPNI is tangible objects can be multiple connected to same physical lane.
Use DPMAC as net device where it represents physical lane.
Below modification done in driver
- Use global DPNI object
- Connect DPMAC to DPNI
- Create and destroy DPMAC
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.
Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
dpni_create API take takes more time as comapred to existing supported
APIs of MC Flib.
So increase MC command timeout.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC represents physical line on the board. This physical
line eventually asscociate with on-board PHY.
So Add an api to return linked PHY ID of DPMAC object.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Print function name along with SerDes Protocol during SerDes Protocol
not supported error.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC object of Management complex controls Physical MAC and MDIO controller.
It provides APIs for MDIO and link state updates. It also provides APIs for
PHY/link configuration.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current Management Complex Flibs does not support APIs for adding and
destroying the objects.
Add APIs to create and destroy objects for DPBP, DPIO, DPNI and DPRC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>