Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increases the kernel size supported for LS2085A platforms:-
- Update environment variables
- Add ramdisk_size in bootargs env variable
- Define CONFIG_SYS_BOOTM_LEN to 64MB
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Primary Mux on I2C1 controller has slave address as 0x75.
So update its address.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable "date" command for QDS and RDB boards
Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Looks like this comment was copied from that of
fdt_get_string_index().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes: 5094eb408a ("fdt: Add functions to retrieve strings")
Acked-by: Simon Glass <sjg@chromium.org>
Avoid clearing the reg property in the memory DT node if no memory
banks have been specified for a board (CONFIG_NR_DRAM_BANKS == 0).
This allows boards to let U-Boot skip the DT memory tinkering in case
other firmware has already setup the node properly before.
This should be safe as all callers of fdt_fixup_memory_banks that use
a computed <banks> value put at least 1 in there.
Add some documentation comments to the header file.
Signed-off-by: Andre Przywara <osp@andrep.de>
Acked-by: Simon Glass <sjg@chromium.org>
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable a SPI environment and store it in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Introduce a new method 'get_count' in the UCLASS_CPU ops to get
the number of CPUs in the system.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 09c3280754 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enabled the USB/EHCI support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Configure and enable the SATA/SCSI (AHCI) support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When compling under 64bit platforms, there are lots of warnings,
like:
drivers/block/ahci.c:114:18: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
u8 *port_mmio = (u8 *)probe_ent->port[port].port_mmio;
^
drivers/block/ahci.c: In function ?.hci_host_init?.
drivers/block/ahci.c:218:49: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
probe_ent->port[i].port_mmio = ahci_port_base((u32) mmio, i);
......
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Baltos has USB0 connected to a USB hub and thus is host-only. USB1
is connected to microUSB connector and thus should use OTG mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Because it is possible for the MTD number to change, causing a
filesystem mount failure, we should use the volume name instead
of the MTD number and let Linux resolve the correct one.
Signed-off-by: Mike Scherban <m-scherban@ti.com>
On STM32F429 gpio PC6/PC7 can be allocated for USART6, as
reported in the comment.
But current code in
drivers/serial/serial_stm32.c
uses a different gpio mapping (PG14/PG9) for USART6.
Fix the comment to match current code in the driver.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>
Use one mtd partition for rootfs and configuration by
means of ubi volumes and get rid of configuration partition.
We can use partition layout for both 256MB and 512MB flash.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
Specify proper U-Boot offset, enable prefetch mode,
increase bootm size and add FIT fallback, if board_name
is not present in kernel-fit.itb image.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
This action is need to make I2C communication with PMIC
stable for low temperature. Print current I2C speed in
SPL for visual control.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
This also came from Linux - according to this thread it has a GPL v2
license like arch/arm/mach-omap2/mux.h:
http://lists.denx.de/pipermail/u-boot/2015-June/217827.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of selecting REGEX when NET is enabled, make it the default, but
allow boards that are tiny to disable it and lose functionality on all
but the first Ethernet adapter.
cm-bf548, bf538f-ezkit, and bf533-stamp need this. None appear to have
more than one Ethernet interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
CONFIG_OF_SEPARATE is default define with CONFIG_OF_CONTROL, removing
this define from the board file to avoid multiple definition warning.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Increase console IO buffer size to 1024 from the previous value of 256.
The previous value was too short for editing environment variables like
ubiboot from the console.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
These options were merged into mx6_common and were seemingly missed
in mx6cuboxi so drop the duplicates
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.
This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.
One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:
powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated
Drop CONFIG_SYS_LONGHELP to free up space.
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.
Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.
By defining a blank NETARGS these errors can be avoided.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Maxin B. John <maxin.john@enea.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Allow SPL to be built with this option so that we can support device tree
control. Disable the simple bus for now in SPL. It may be needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is used by some boards, so support it with driver model. This
is really ugly - we should rewrite this driver once all users are moved to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
We try to avoid typedefs and these ones are easy enough to remove. Before
changing this header in the next patch, remove the typedefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function is used before jumping to U-Boot, but in that case we don't
always want to disable caches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
