Replace Mateusz as Maintainer for ARM Snapdragon arch.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Acked-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add dump trace command which dump all trace
buffer content in a much more readable fashion
than md.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The header definitions are needed for reading
record information in cmd/iotrace.c
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Run AVB 2.0 full verification chain, avb verify
2. Check if 'avb get_uuid' works, compare results with
'part list mmc 1' output
3. Test `avb read` commands, which reads N bytes from a partition
identified by a name
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Add vbmeta partition info to android partition layout for TI
platforms.
2. Add support of AVB 2.0 (including avb subset of commands) for am57xx HS
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
[trini: Move to include/environment/ti/boot.h, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
1. Add initial support of boot states mode (red, green, yellow)
2. Add functions for enforcing dm-verity configurations
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
avb init - initialize avb2 subsystem
avb read_rb - read rollback index
avb write_rb - write rollback index
avb is_unlocked - check device lock state
avb get_uuid - read and print uuid of a partition
avb read_part - read data from partition
avb read_part_hex - read data from partition and output to stdout
avb write_part - write data to partition
avb verify - run full verification chain
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Implement AVB ops on top of existing mmc subsystem API. Currently there
is a full implementation of such operations, defined by [1]
AVB2.0 specification:
.read_from_partition() - reads N bytes from a partition identified by
a name.
.write_to_partition() - Writes N bytes to a partition identified by a name.
.validate_vbmeta_public_key() - checks if the given public ‘vbmeta’
partition is trusted.
.get_unique_guid_for_partition() - Gets the GUID for a partition identified
by a string name.
As [1] specification recommends to use tamper-evident storage for storing
rollback indexes and device state (LOCKED/UNLOCKED),
currently are only stubs instead of full implementation for these ops:
.read_rollback_index() - Gets the rollback index for a given index location
.write_rollback_index() - Sets the rollback index to a given location
.read_is_device_unlocked() - Gets where the device is unlocked
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Add libavb lib (3rd party library from AOSP), that implements support of
AVB 2.0. This library is used for integrity checking of Android partitions
on eMMC.
libavb was added as it is and minimal changes were introduced to reduce
maintenance cost, because it will be deviated from AOSP upstream in the future.
Changes:
- license headers changed to conform SPDX-style
- avb_crc32.c dropped
- updates in avb_sysdeps_posix.c/avb_sysdeps.h
For additional details check [1] AVB 2.0 README.
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
The soms with 4GB ddr have a rowaddr of 16 not 15, this allows
the detection mechanism to properly identify them as 4GB.
However these soms can be populated with whatever amount of
memory the customer requests therefor we need a ram stride test.
We can not use the get_ram_size() function because not all 4GB's
of DDR is addressable on a 32-bit architecture. Therefore instead
we use a memory stride of 128MB's and look for the address that
the memory wraps. This function is used for all som types to
catch most memory configurations.
This is a revised version of Rabeeh Khoury's original code.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The naming with "UART" is obviously wrong, we fix this here.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The get_board_rev() is not needed anymore as a generic function
for the imx53 SoC has been used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change gives the opportunity to adjust Linux command line for the
imx53 device with some legacy data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Since kernel commit 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate
into cpu and baseboard dts") the dtb name has changed.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
ARCH_MX6 has default values for SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
and SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR.
Do the same for ARCH_MX7 so that users may have a consistent
experience through the i.MX families.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
If many values differ from the defaults, overriding the full table
is simpler and more space efficient than tweaking it through
mxs_adjust_memory_params().
Signed-off-by: Mans Rullgard <mans@mansr.com>
According to the Cortex-A7 TRM, for ACTLR.SMP bit "You must ensure this bit
is set to 1 before the caches and MMU are enabled, or any cache and TLB
maintenance operations are performed".
ROM sets this bit in normal boot flow, but when in serial download mode,
it is not set.
Here we add it in u-boot as a common flow for all i.MX cortex-a7 platforms,
including mx7d, mx6ul/ull and mx7ulp.
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: adapted to U-Boot mainline codebase and make checkpatch happy]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Without this change the following warning shows up when building:
board/liebherr/display5/display5.c:270:3:
warning: implicit declaration of function ‘eth_env_set_enetaddr’ [-Wimplicit-function-declaration]
This commit fixes this issue.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GPT and restore it if needed.
To test it:
display5 > mmc write 0x12000000 4 8
It will overwrite the primary GPT table.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Test case:
The fitImage gets corrupted:
truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset
[board shall hang in SPL with
"Trying to boot from MMC1" information]
Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To enter the special mode, one needs to short cut two pads with e.g. screw
driver.
After power up the SPL will execute u-boot in which proper actions will be
taken.
It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.
It removes the support for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reason).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Force booting through u-boot proper when environment error encountered
(as a result of either broken SPI-NOR or erased envs).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
It may be necessary to update the content of the whole SPI-NOR memory at
once with using a single command (tftp_sf_img).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
