UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.
Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
We need to update gd in assamble code after relocate,
this is a fix to:
adc421e arm: move gd handling outside of C code
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.
Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.
Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes the USB 3.0 support for the a38x SOC.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
When a high speed card is connected to mx25 the following error is seen:
U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The API for get priv pointer is wrong, fix it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.
Add code to setup simplefb for Allwinner DE2 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>