This source file, which I got by the vendor in their own port,
was not actually executing because lib-based compilation
didn't call lowlevel_init (we have CONFIG_SKIP_LOWLEVEL_INIT).
With the change to object-based linking, an undefined symbol in
this file started hitting in the final link.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Move the header file "ftsdmc020.h" (SDRAM Controller)
to "include/faraday" folder.
This change will let other SoC which also use ftsdmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
9260 (64MB RAM & nor boot)
9260_nand (64MB RAM & nand boot)
9G20_128M (128MB RAM & nor boot)
9G20_nand_128M (128MB RAM & nand boot)
(nor boot is using lowlevel init)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.
The board support is based on the BeagleBoard implementation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
CM-T3730 is exactly the same board as CM-T35, but it has
TI DM3730 SoC onboard and therefore some changes have to take place
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Use CONFIG_OMAP3_MMC in cm-t35 configuration file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Jason Liu <r64343@freescale.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Make the copyright notices in the x86 files consistent and update them with
proper attributions for recent updates
Also fix a few comment style/accuracy and whitespace/blank line issues
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
By including <config.h> in the ld script, CONFIG_SYS_MONITOR_LEN (defined
in the boards config file) can be used in lieu of FLASH_SIZE (defined in
the board specific config.mk)
As this is the last remaining entry in the board specific config.mk, this
file can now be removed
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
This reads the DIP switch on mgcoge. The DIP switch is connected to
the BFTICU (0x40000089) FPGA. If the DIP switch is set the environment
variable 'actual_bank' is set to 0 and starts the SW in bank0.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed, it is already unused.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This patch fixes ea20 after commit 6d8962e814
where $(obj)lib$(BOARD).a was changed to $(obj)lib$(BOARD).o in almost all the
Makefiles except ea20, probably due to merge path of the changes in 2010.12.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
Acked-by : Stefano Babic <sbabic@denx.de>
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Flash might be in unknown state when u-boot is started with jtag.
And got wrong env data. So reset it in board early init.
We cannot use generic cfi flash routines, because flash_init() is
not run yet.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
commit cfbe861506 removed the definition of
monitor_flash_len from the eNET which was not picked up due to extensive
use of the SRAM configuration target for testing
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't want/use this value for Blackfin boards, so punt it and have the
common code error out when people try to use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Only the first run of boards had a ksz switch on it, so if building for a
newer silicon rev or SPI is disabled, don't bother checking for the ksz.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changed the following DDR timing parameters for 800Mt/s:
tRRT BL/2+1 to BL/2
tWWT BL/2+1 to BL/2
tWRT BL/2+1 to BL/2
tRWT BL/2+1 to BL/2
REFINT 6500ns to 7800ns
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
RevB boards never really made it outside of Freescale and have been
replaced with RevC & RevD which had various board bug fixes.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCA9557 is parallel I/O expansion device on I2C bus which stores various
board switch settings like NOR Flash-Bank selection, SD Data width.
On board:
switch SW5[6] is to select width for eSDHC
ON - 4-bit [Enable eSPI]
OFF - 8-bit [Disable eSPI]
switch SW4[8] is to select NOR Flash Bank for Booting
OFF - Primary Bank
ON - Secondary Bank
Read board switch settings on p1_p2_rdb and configure corresponding
eSDHC width.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using DDR as RAMBOOT base instead of L2SRAM for SDCard and SPI Flash
boot loaders because:
- P1_P2_RDB boards have soldered DDR so no need for SPD
- Also P102x has 256K L2 cache size so becomes a limiting factor for
size of image that could be loaded in SRAM mode and would require three
stage boot loader (TPL).
Changes done:
1. CONFIG_SYS_TEXT_BASE to 0x11000000
2. CONFIG_RESET_VECTOR_ADDRESS to 0x1107fffc
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The NXID EEPROM format comes in two versions, v0 and v1. The only
difference is in the number of MAC addresses that can be stored. NXID v0
supports eight addresses, and NXID v1 supports 23.
Rather than allow a board to choose which version to support, NXID v0 is
now considered deprecated. The EEPROM code is updated to support only
NXID v1, but it can still read EEPROMs formatted with v0. In these cases,
the EEPROM data is loaded and the CRC is verified, but the data is stored
into a v1 data structure. If the EEPROM data is written back, it is
written in v1 format. This allows existing v0-formatted EEPROMs to
continue providing MAC addresses, but any changes to the data will force
an upgrade to the v1 format, while retaining all data.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Most of time U-boot doesn't get an exact clock number. For example, clock
900MHz may be detected as 899.99MHz. 800MHz could be 799.99MHz. Update the
table to align the desired clocks in the middle.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq()
and every 86xx board uses get_bus_freq(). If implement get_ddr_freq()
as a static inline to call get_bus_freq() we can remove
fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq()
directly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the include of mpc85xx/u-boot-nand.lds to utilize
CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We've been utilizing board_lmb_reserve to reserve the boot page for MP
systems. We can just move this into arch_lmb_reserve for 85xx & 86xx
systems rather than duplicating in each board port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We enable SDHC_CD and SDHC_WP signals (pin muxed with GPIO8 & GPIO9
respectively).
We enable EXT2, FAT, and parition support for both MMC & USB configs.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.
Based on patch from Poonam Aggrwal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than having #defines DATARATE_*_MHZ, lets just match what we do on
the SPD code and convert the DDR frequency into MHZ and just compare
with a constant.
Based on patch from Poonam Aggrwal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ngPIXIS is an FPGA used on the reference boards of most Freescale PowerPC
SOCs. Although programming the ngPIXIS is mostly standard on all boards that
have it, the P1022DS is unique in that the ngPIXIS needs to be programmed in
"indirect" mode whenever the video display (DIU) is active.
To support indirect mode, and to make it easier to support other quirks on
future reference boards, the low-level ngPIXIS functions are all marked as
weak, so that board-specific code can override any of them. We take advantage
of this feature on the P1022DS, so that we can properly reset the board when
the DIU is active.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The first, the cpu_init.o have already been link for cmd_link_o_target
atfer compile, But, The link script re-link the point file. So the link
machine will generate multiple definition error information.
The second, Since the first 4kB of nand boot featue code move to nand_spl,
So It is not necessary to force the cpu_init.o in non-nand boot.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Modify Makefile for cpu_init.c and Start.s use some label,this defined
u-boot.lds of arch/arm/cpu/arm1176. But SMDK6400 use the link script
board/samsung/smdk6400/u-boot-nand.lds. So add some label form u-boot.lds
to u-boot-nand.lds
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Update the PCIe address map to match standard FSL memory map.
Additionally, fix the TLBs so the cover the PCIe address space properly
so cards plugged in like an e1000 work correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested all possible values for clk_adjust and write_data_delay for dual
rank UDIMM and RDIMM to revise the tables.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If no Flash is connected to cs1, Linux crashes, because
reg entries are not correct adapted.
Following fix is needed:
- swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as
flash bank 1 is on chipselect 0 and flash bank 2 on
chipselect 1
- call fdt_fixup_nor_flash_size() from ft_board_setup()
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
This patch revised clk_adjust and wrlvl_start timings for corenet_ds, based
on testing on Virtium VL33B5163F-K9S and Kingston KVR1333D3Q8R9S/4G.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For DDR3 controller, the clk_adjust and wrlvl_start are platform-dependent.
The best values should be picked up from the middle of all working
combinations. This patch updates the table with confirmed values tested on
Hynix dual-rank UDIMMs (HMT125U7BFR8C-H9) at 1300MT/s, 1200MT/s, 1000MT/s,
900MT/s, 800MT/s and Kingston quad-rank RDIMMs (KVR1333D3Q8R9S/4G) at 1300MT/s,
1200MT/s, 1000MT/s.
Signed-off-by: York Sun <yorksun@freescale.com>
Position independant functionality is due for removal from the x86
architecture, so create two distinct configurations - One for Flash and
one for SRAM
The "mac id" command is used to initialize the EEPROM data to a specific
format, but it was not updating the CRC. This didn't cause any real
problems, because writing the data to the EEPROM will always update the
CRC anyway, but it did result in a bogus CRC warning.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
All dbau1x00 boards use the CFI driver so this stub driver is useless
and should not be compiled.
This patch fixes the error:
u-boot-git/board/dbau1x00/flash.c:34: multiple definition of `flash_init'
drivers/mtd/libmtd.o:u-boot-git/drivers/mtd/cfi_flash.c:2084: first defined here
board/dbau1x00/libdbau1x00.o: In function `write_buff':
u-boot-git/board/dbau1x00/flash.c:40: multiple definition of `write_buff'
drivers/mtd/libmtd.o:u-boot-git/drivers/mtd/cfi_flash.c:1265: first defined here
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The linker of recent toolchains complains about multiple definitions
on final linking of u-boot binary. This patch removes all redundant
object files from u-boot.lds those are already added to .text section
by the linker.
That patch could not be tested but the resulting u-boot.map still looks
good. The start symbol is at 0xB0000000, the environment at 0xB0008000
so u-boot should boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.
This patch supports the following functions:
- 256MB DDR3-SDRAM
- SPI ROM
- Ethernet
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
unnecessary config.mk file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for Samsung s5pc210 universal board
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* add CONFIG_SYS_SDRAM_BASE and CONFIG_SYS_INIT_SP_ADDR
* do not update gd->bd in dram_init() because bd is unavailable then
* move CONFIG_SYS_TEXT_BASE from config.mk to a320evb.h
* remove config.mk
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Support for DM6467 was incomplete and the build failed
as well. Patches were sent to the list but have not been
added. This enhances the DM6467 support.
Some more patches will need to be sent to bring
it in line with what is available in internal TI
trees
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
After the merger of the next branch, the DM365 was
broken. A function used only by DA8xx based SOCs was
being incorrectly called. So fix it.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
Supported:
MMC
IDE
PMIC
SPI flash
LEDs
I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
The early bootup information is not print out due to
the UART pin iomux not set up correctly before board_init
Add the board_early_init_f function and enable the
CONFIG_BOARD_EARLY_INIT_F. Move the UART pin setting
from board_init to board_early_init_f function.
This patch also move the FEC pin iomux setup to the
board_early_init_f.
Signed-off-by: Jason Liu <r64343@freescale.com>
Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.
Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx
Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot cannot be compiled after disabling CONFIG_PCI.
Place PCI related codes under #ifdef CONFIG_PCI
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.
Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than defining it config.mk we can set it in config.h and remove
config.mk from several boards that don't need it.
We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for
config.h to set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
The MPC852 based mgsuvd and kmsupx4 boards from keymile
were initially ported but later on not developed further. So
the respective files were removed to avoid unneeded merging
and maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe
controllers for SRIO.
We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.
We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.
Introduced the following standard defines for board config.h:
CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available
(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)
[ These mimic what we have for PCI and PCIe controllers ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Remove duplicated code in SBC8548 board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Remove duplicated code in SBC8641 board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
Remove duplicated code in MPC8610HPCD board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in P1_P2_RDB boards and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8569MDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8568MDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in TQM 85xx boards and utilize the common
fsl_pcie_init_board().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CC: wd@denx.de
Remove duplicated code in MPC8xxx XES boards and utilize the common
fsl_pcie_init_board().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CC: Peter Tyser <ptyser@xes-inc.com>
Remove duplicated code in MPC8548CDS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8641HPCN board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8544DS board and utilize the common
fsl_pcie_init_ctrl(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
We don't use the full fsl_pcie_init_ctrl() since we have to handle PCIE3
specially to setup the additional memory map region and we utilize a
single LAW to cover the controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in P2020DS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicated code in MPC8572DS board and utilize the common
fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spaces to cause the informational prints to line up with
the ones from init_func_ram() in board.c. Output now looks like
this:
....
DRAM: Detected 4096 MB of memory
This U-Boot only supports < 4G of DDR
You could rebuild it with CONFIG_PHYS_64BIT
DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off)
....
The prints from lbc_sdram_init() have also been modified to line
line up and changed to start with "LBC SDRAM" instead of the
confusing "SDRAM".
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sdram_init() is used to initialize sdram on the lbc. Rename it
accordingly.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts. Most
of the initdram() functions were identical, with 2 common differences:
1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others. I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.
2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document. It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled. This seems bad.
The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also, change this code to use phys_size_t instead of long int.
Using common naming for this function will enable us to use the common
initdram() for 85xx going forward. Other than the type change,
this is just a code rearrange.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new is_serdes_configured to determine if TSECs are in SGMII mode and
report that on the various boards that use or can be configured in SGMII
mode in board_eth_init() instead of in the PCI init code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting
from NAND.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This will help us go to a fixed initdram() for all 85xx boards going
forward. sdram_setup() had an argument that it didn't need, since the
value was #defined.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PM854/PM856 boards are no longer maintained and thus we are removing
support for them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
config.mk only mkdirs $(obj), but we have objects shared with other
boards located on other dirs.
This patch mkdirs the needed dirs for the xlnx-generic boards.
Signed-off-by: Stefan Roese <sr@denx.de>
16MiB NAND TLB window is way too big. Reduce it to 1KiB.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 98e6956 "mpc52xx: add support for tqm52xx based board charon"
caused build warnings on some systems. Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch supports T-SH7706LSR board.
This is constitution almost same as shmin (T-SH7706LAN).
Therefore, most functions work by a change of the setting of config.
http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706LSR.htm
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds support for the SHMIN SH7706 board(T-SH7706LAN).
The CPU of this board is SH7706.
There are SDRAM of 32M byte, Flash memory of 512K byte, Serial,
10Base Ether and MMC.
http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htm
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Convert the variable omap3_evm_version to u32 to work around
some broken linkers from older tool chains. E.g. CodeSourcery's
2009q1-203 ld 2.19.51.20090205. Without this, these linkers
stop linking 'omap3_evm' or at least issue a warning. Like
arm-none-linux-gnueabi-ld: section .bss [8003f5e0 -> 8007e337] overlaps section .rel.dyn [8003f5e0 -> 80044e57]
arm-none-linux-gnueabi-ld: section .dynsym [80044e58 -> 80044ef7] overlaps section.bss [8003f5e0 -> 8007e337]
arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5e0 overlaps previous sections
CC: Sanjeev Premi <premi@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
The following commit:
commit 882b7d726f
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Oct 20 03:41:17 2010 -0400
do_reset: unify duplicate prototypes
missed the 74xx_7xx and mpc86xx arches and the ppmc7xx board do_reset()
functions which resulted in build errors such as:
cpu.c:128: error: conflicting types for 'do_reset'
include/command.h:102: error: previous declaration of 'do_reset' was here
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch includes the following changes for the lwmon5 board support:
- Enable cache in SDRAM
- Use common EHCI driver instead of the PPC4xx specific OHCI driver
This can be done since only high-speed devices are connected.
- Remove cached TLB entry again after ECC setup
- Use correct define for cache enabling
(CONFIG_4xx_DCACHE instead of CONFIG_SYS_ENABLE_SDRAM_CACHE)
- Enable FIT image support
Signed-off-by: Stefan Roese <sr@denx.de>
The t3corp board has an Xilinx DS617 flash chip connected to the
onboard FPGA. This patch adds support for these chips. Board
specific flash accessor functions are needed, since the chips
can only be read correctly in 16bit mode.
Additionally the FPGA chip-selects are configured for device-paced
transfers (ready is enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
* Processor upto 1.2GHz
* Parallel 1Gb x8 DDR2-1066 MHz
* 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
* Footprints for eMMC/eSD NAND & MMC x8 card
* 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
* SEAF memory board, subset of PISMO2
With Peripherals:
* 4.3” WVGA 24-bit LCD
* Audio codecs (AC97 & I2S), TSI
* VGA camera
* Video in via 3 RCA jacks, and HDMI type C out
* Marvell 88W8688 802.11bg/BT module
* GPS RF IC
* Dual analog mics & speakers, headset jack, LED, ambient light sensor
* USB2.0 HS host (A), OTG (micro AB)
* FE PHY, PCIE Mini Card slot
* GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR
This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
- serial console in PSC1
- 128MiB DRAM
- 32MiB Flash
- FEC Ethernet
- 2 I2C busses
- FPGA on CS3
- IDE
- VGA SMI501
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes the acadia_nand and kilauea_nand linker scripts
which have been missing in commit ee8028b7 [ppc4xx: Cleanup for
partial linking and --gc-sections]
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bernhard Weirich <Bernhard.Weirich@riedel.net>
On the P1022, the pins which drive the video display (DIU) are muxed with the
local bus controller (LBC), so if the DIU is active, the pins need to be
temporarily muxed to LBC whenever accessing NOR flash.
The code which handled this transition is checking and changing the wrong
bits in PMUXCR.
Also add a follow-up read after a write to NOR flash if we're going to
mux back to DIU after the write, as described in the P1022 RM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Recent cleanup actions resulted in a number of config.mk files that
contained only LDSCRIPT definitions. Move these into th respective
board config files and remove the now empty config.mk files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Detlev Zundel < dzu@denx.de>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher<hs@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Recent cleanup actions resulted in a number of config.mk files that
contained only redundant entries like
PLATFORM_CPPFLAGS += -I$(TOPDIR)
or settings of variables that were not used anywhere in the code, like
TEXT_END = 0xfe080000
Remove these unnecessary files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott McNutt <smcnutt@psyent.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Tolunay Orkun <torkun@nextio.com>
Cc: Frank Panno <fpanno@delphintech.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Brad Kemp <Brad.Kemp@seranoa.com>
Acked-by: Heiko Schocher<hs@denx.de>
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As more Davinci 8xx board can be added, move common code
to be shared between boards.
* rebased ontop of Sugosh's patches
* moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
arch/arm/include/asm/arch-davinci/davinci_misc.h from to
arch/arm/include/asm/arch-davinci/da8xx_common.h
* don't define dram functions in PRELOADER
* move sync_env_enetaddr into existing EMAC ifdef
* use misc.c in hawkboard nand_spl
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove the board_init_f function from nand_spl/nand_boot.c. This
function is to be defined by all boards using the nand_spl
functionality in their individual board directory.
Currently this function was being used by the smdk6400 board. Added
the board specific function definition.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
board/davinci.
Move the davinci common headers to the architecture specific
include file path.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix ca9x4_ct_vxp build error
Configuring for ca9x4_ct_vxp board...
board/armltd/vexpress/libvexpress.o: In function `udelay':
u-boot.git/board/armltd/vexpress/ca9x4_ct_vxp.c:161: multiple
definition of `udelay'
lib/libgeneric.o:u-boot.git/lib/time.c:34: first defined here
lib/libgeneric.o: In function `udelay':
zlib.c:(.text+0x1ee8): undefined reference to `__udelay'
Signed-of-by: Dirk Behme <dirk.behme@googlemail.com>
This patch fixes build errors in the vexpress system:
- Removed sys_proto.h requirement from syslib.c.
- Switched vexpress to the default armv7 linker script.
- Renamed TEXT_BASE to CONFIG_SYS_TEXT_BASE.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Since the driver is used not only on Freescale boards,
we move it to a common place for video drivers as
suggested by Wolfgang. The patch also cleans up the
top level Makefile.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a
default value they will get put into the BSS if they aren't defined
elsewhere. This is problematic as we try to utilize hwconfig before
we've relocated and thus BSS isn't setup.
Instead of giving dummy values in the board files that utilize this
feature, we can just initialize the variables to an empty string and
thus move them out of the BSS if they aren't defined elsewhere.
Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated
with string pointers vs arrays.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required
with relocation support. This is the load address for primary
boot loader (x-loader).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness). Unify them
all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
