Commit Graph

2607 Commits

Author SHA1 Message Date
Anton Vorontsov
7e2ec1de1d mpc83xx: MPC837XEMDS: Initialize SerDes before negating PCIE reset signal
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.

Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:13:11 -06:00
Anton Vorontsov
7e91558032 mpc83xx: MPC837XERDB: Add PCIe support
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-23 15:52:35 -06:00
Dirk Behme
cfcdf4a9b3 OMAP3: Pandora: Update pin mux
Clock pin must have input enabled for MMC3 to work.
Also enable pull-ups for cmd/data lines to be consistent
with remaining MMC host pin setup.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
6530a8bf8a OMAP3: Add OMAP3 auto detection
This patch adds OMAP3 cpu type auto detection based on OMAP3 register
and removes hardcoded values.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
f956fd0338 OMAP3: Beagle: Add board revision detection
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.

To handle board differences you can call function beagle_get_revision().
E.g.:

if (beagle_get_revision()) {

/* do special revision C stuff here */

}

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
288f3cd912 OMAP3: Overo: Clean up pin mux and GPIO configuration
* Make Overo GPIO114 an input for touchscreen PENDOWN
* Make Overo GPIO144-147 readable
* Make Overo EHCI pinmux match beagle rev c setup
* Adjust pinmux for SMSC911X network chip support
* Remove unnecessary GPIO setup
* Fix merge error in Makefile

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Jean-Christophe PLAGNIOL-VILLARD
9751a456f7 davinci: fix implicit declaration of function 'davinci_errata_workarounds'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22 17:49:43 +01:00
Hugo Villeneuve
0cd18fa982 ARM DaVinci: Add common peripherals and modules enable functions.
Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
2009-02-22 13:42:25 +01:00
Alessandro Rubini
d3be1bcae7 Enable Ethernet for Nomadik 8815 Evaluation Kit
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22 13:40:31 +01:00
Wolfgang Denk
09fee8e867 Coding Style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22 01:19:52 +01:00
Heiko Schocher
9e80bb2162 82xx, mgcoge: updates for 2009.03
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
  before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19 21:20:16 +01:00
Heiko Schocher
df909554e2 8xx, mgsuvd: updates for 2009.03
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
  before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19 21:19:45 +01:00
Wolfgang Denk
32482be677 TQM8xxL: make some room in low memory for future needs
THe TQM8xxL use a ahnd-optimized linker script to efficiently use the
small boot sectors in the flash. This patch makes some room in the
first sector to prepare for a size increase of lib_generic/vsprintf.o
by a future patch.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-19 14:01:42 +01:00
Wolfgang Denk
44a01a73e8 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-02-19 00:50:08 +01:00
Wolfgang Denk
9eb468da3f Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-19 00:46:32 +01:00
Wolfgang Denk
b8845abdc0 Fix build errors after making flash_get_info() non-static
Fix for these build problems:
error: static declaration of 'flash_get_info' follows non-static declaration

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-18 22:40:08 +01:00
Stefan Roese
f50fe4bd61 ppc4xx: Some more PMC405 coding-style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 14:05:37 +01:00
Matthias Fuchs
2f6eb9170b ppc4xx: Update PMC405 board support
This patch prepares the good old PMC405 board support for
upcoming PMC405V2 patches.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 13:50:35 +01:00
Matthias Fuchs
c553b5f4a0 ppc4xx: Cleanup PMC405 board support
This patch fixes coding style for PMC405 board support.
Also some unneeded features/code is removed.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 13:50:29 +01:00
Andy Fleming
e1ac387f46 83xx: Add eSDHC support on 8379 EMDS board
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:43 -06:00
Andy Fleming
80522dc836 85xx: Add eSDHC support for 8536 DS
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:43 -06:00
Andy Fleming
e0c4fac79d TQM85xx: Fix a couple warnings in TQM8548 build
The ecm variable in sdram.c was being declared for all 8548, but only
used by specific 8548 boards, so we make that variable require those
specific boards, too

The nand code was using an index "i" into a table, and then re-using "i"
to set addresses for each upm.  However, then it relied on the old value
of i still being there to enable things.  Changed the second "i" to "j"

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:06:03 -06:00
Wolfgang Grandegger
cf07a5baec MPC85xx: TQM8548: workaround for erratum DDR 19 and 20
This patch adds the workaround for erratum DDR20 according to MPC8548
Device Errata document, Rev. 1: "CKE signal may not function correctly
after assertion of HRESET". Furthermore, the bug DDR19 is fixed in
processor version 2.1 and the work-around must be removed.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:02 -06:00
Wolfgang Grandegger
080408fdc7 MPC85xx: TQM8548: use cache for AG and BE variants
This patch makes accesses to the system memory cachable by removing the
caching-inhibited and guarded flags from the relevant TLB entries for
the TQM8548_BE and TQM8548_AG modules. FYI, the Freescale MPC85* boards
are configured similarly.

This results in a big averall performace improvement. TFTP downloads,
NAND Flash accesses, kernel boots, etc. are much faster.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:02 -06:00
Wolfgang Grandegger
dc5f55d636 MPC85xx: TQM8548_AG: add 1 GiB DDR2-SDRAM configuration
This patch add support for the 1 GiB DDR2-SDRAM on the TQM8548_AG
module.

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:01 -06:00
Wolfgang Grandegger
88b0e88d18 MPC85xx: TQM8548: fix SDRAM timing for 533 MHz
According to new TQM8548 timing specification:
Refresh Recovery: 34 -> 53 clocks
CKE pulse width:  1 -> 3 cycles
Window for four activities: 13 -> 14 cycles

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:00 -06:00
Wolfgang Grandegger
ad7ee5d43b MPC85xx: TQM8548: add support for the TQM8548_BE module
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Wolfgang Grandegger
a318234878 MPC85xx: TQM85xx: make standard PCI/PCI-X configurable
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:58 -06:00
Wolfgang Grandegger
31ca9119c3 MPC85xx: TQM85xx: fix flash protection for boot loader
As the reset vector is located at 0xfffffffc, all flash sectors from the
beginning of the U-Boot binary to 0xffffffff must be protected. On the
TQM8548-AG having small sectors at the end of the flash it happened that
the last two sector were not protected and an "erase all" left an
un-bootable system behind:

Bank # 2: CFI conformant FLASH (32 x 16)  Size: 32 MB in 270 Sectors
  AMD Standard command set, Manufacturer ID: 0xEC, Device ID: 0x257E
  Erase timeout: 8192 ms, write timeout: 1 ms

  FFFA0000 E RO   FFFC0000   RO   FFFE0000   RO   FFFE4000   RO   FFFE8000   RO
  FFFEC000   RO   FFFF0000   RO   FFFF4000   RO   FFFF8000 E      FFFFC000

The same bug seems to be in drivers/mtd/cfi_flash.c:flash_init() and many
board BSPs as well.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:58 -06:00
Peter Tyser
4ef630df77 86xx: Reset update
Update the 86xx reset sequence to try executing a board-specific reset
function.  If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ.  Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-02-16 18:05:56 -06:00
Kumar Gala
cb69e4de87 85xx: print boot header info to distinquish 36-bit addr map on MPC8572 DS
Added some info that is printed out when we boot to distiquish if we
built MPC8572DS_config vs MPC8572DS_36BIT_config since they have
different address maps.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:54 -06:00
Andy Fleming
feede8b070 Fixup SGMII PHY ids in the device tree
The device tree's PHY addresses need to be fixed up if we're using the
SGMII Riser Card.

The 8572, 8536, and 8544 DS boards were modified to call this function.

Code idea taken from Liu Yu <yu.liu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:05:54 -06:00
Kumar Gala
b67305120a 85xx: Fix bug in device tree setup in 36-bit physical confg
In the 36-bit physical config for MPC8572DS when need the start address
of memory and it size to be kept in phys_*_t instead of a ulong since
we support >4G of memory in the config and ulong cant represent that.
Otherwise we end up seeing the memory node in the device tree reporting
back we have memory starting @ 0 and of size 0.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:52 -06:00
Kumar Gala
ad97dce184 85xx: Fix address map for 36-bit config of MPC8572DS
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map.  Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus.  We need
to use the new mapping functions to handle that read properly in the
36-bit config.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:52 -06:00
Stefan Roese
cef0efaf2f ppc4xx: Fix problem with board_eth_init() vs cpu_eth_init() on AMCC boards
Some AMCC eval boards do have a board_eth_init() function calling
pci_eth_init(). These boards need to call cpu_eth_init() explicitly now
with the new eth_init rework.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-12 06:08:07 +01:00
Wolfgang Denk
f15c6515fc Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-12 00:08:39 +01:00
Becky Bruce
49f46f3bf0 mpc8641hpcn: Clean up PCI mapping concepts
Clean up PCI mapping concepts in the 8641 config - rename _BASE
to _BUS, as it's actually a PCI bus address, separate virtual
and physical addresses into _VIRT and _PHYS, and use each
appopriately.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:30:17 +01:00
Becky Bruce
d35ae5a938 powerpc: Move duplicated BAT defines to mmu.h
The BAT fields are architected; there's no need for these to be in
cpu-specific files.  Drop the duplication and move these to
include/asm-ppc/mmu.h.  Also, remove the BL_xxx defines that were only
used by the alaska board, and switch to using the BATU_BL_xxx defines
used by all the other boards.  The BL_ defines previously in use
had to be shifted into the proper position for use, which was inefficient.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:27:40 +01:00
Becky Bruce
2ecca34017 mpc8641hpcn: Set up outbound pci windows before inbound
Because the inbound pci windows are mapped generously, set up
the more specific outbound windows first.  This way, when we
search the pci regions for something, we will hit on the more
specific region.  This can actually be a problem on systems
with large amounts of RAM.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:26:45 +01:00
Ilya Yanok
0d19f6c8cb qong: support for Dave/DENX QongEVB-LITE board
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-10 00:22:31 +01:00
Kumar Gala
ff4e66e93c pci: Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY for clarity
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.

Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-07 23:50:04 +01:00
Wolfgang Denk
045639397d Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-02-07 22:53:45 +01:00
Wolfgang Denk
1b33a62bf9 Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2009-02-07 22:08:53 +01:00
Mike Frysinger
4b7e3d045c Blackfin: move default boot SPI CS to common code
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-05 21:25:36 -05:00
Ralph Kondziella
70a4da45e1 ADS5121 Add PATA support
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
    use ips clock not lpc
    port forward to current u-boot release

Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 15:40:29 -07:00
Martha Marx
abfbd0ae49 ADS5121 Add IC Ident Module (IIM) support
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.

Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 15:40:20 -07:00
John Rigby
14d19cd1bc ADS5121 Fix rev2 silicon pci iopad config
Reset config is not correct

Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
John Rigby
4c154252c4 ADS5121 DIU Add diu_bmp_addr env
Add support for using a bmp other than
FSL_Logo_BMP for the DIU splash screen.

Can now set the env var "diu_bmp_addr" to
the address of a BMP in flash to use instead
of the default FSL_Logo_BMP.

Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
John Rigby
92c20fbd3a ADS5121 DIU Make inclusion of FSL logo optional
Make inclusion of FSL logo optional and
turn it off by default.

Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
Mike Frysinger
6e87ea0ca9 Blackfin: add port muxing for BF51x SPI
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02 12:27:16 -05:00