Set only the 0-3 bits of the FPGA_RST_CTRL register
as other bits should not be set to 1.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The driver should setup slcr state according
to slcr operations.
Reported-by: Andrey Filippov <andrey@elphel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix c&p error in zynq_slcr_devcfg_enable() commentary
and extending it with description according
to Zynq TRM also in zynq_slcr_devcfg_disable().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
arch/arm/cpu/armv7/zynq/slcr.c:21:6: warning: symbol 'zynq_slcr_lock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:27:6: warning: symbol 'zynq_slcr_unlock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:34:6: warning: symbol 'zynq_slcr_cpu_reset' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:54:6: warning: symbol 'zynq_slcr_gem_clk_setup' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:81:6: warning: symbol 'zynq_slcr_devcfg_disable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:94:6: warning: symbol 'zynq_slcr_devcfg_enable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:107:5: warning: symbol 'zynq_slcr_get_boot_mode' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:113:5: warning: symbol 'zynq_slcr_get_idcode' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.
Added this functionality on board_late_init as it's not
needed for normal initializtion part.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
If you don't wait you will loose the first sent packet
even all bits in emacps are correctly setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
The patch provides slcr base address initialization support
and a support to reset the cpu through slcr driver,
hence removed the reset_cpu() from board.c.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
