We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)
This layout is matching the lpc32xx NAND SLC Linux Kernel driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition
The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Make the support for 4K subpage I/O on a SPI NOR flash configurable.
A board which requires the SPI NOR to be accessed in larger 32KiB
or 64KiB pages can disable the 4K subpage support, but by default,
the support for 4K subpage I/O is enabled. The functionality of this
option is the same as CONFIG_MTD_SPI_NOR_USE_4K_SECTORS in Linux.
This is extremely useful in case one uses UBI on a SPI NOR flash.
UBI needs at least 15k EBs and can not work on a flash which uses
4k ones, so disabling the support for 4k subpages lets UBI work on
such flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Disable subpage writes as we do not provide ecc->hwctl.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.
This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).
I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
remove unneeded udelay() in this function, as we use
the dev_ready pin.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Since commit 09c3280754 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).
Signed-off-by: Stefan Agner <stefan@agner.ch>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
the special handling of OOB (spareonly).
Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.
However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.
Signed-off-by: Stefan Agner <stefan@agner.ch>
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Freeing allocated memory to priv before returning
from the function
Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.
This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).
I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This printf() should have a newline at the end. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
