The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 181bd9dc61 "kconfig: add config option for shell prompt" replaced
define V_PROMPT with Kconfig option SYS_PROMPT. This crossed with patches
adding Tegra T210 boards. Migrate the boards to the new scheme.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While T210 boards all have 38.4MHz crystals, per the TRM, the only
supported configuration is to divide the crystal frequency by 2 to
generate clk_m, which is what feeds the ARM generic timers amongst other
things. Fix the value of COUNTER_FREQUENCY to reflect this divide-by-2.
When I queried the 19.2 value in Tom's original T210 patches, I wasn't
aware of this extra divide-by-2, and didn't notice any effect from the
incorrect value, since its only used if U-Boot is booted in EL3, whereas
I'm booting it in EL2.
Reported-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested on my TI186x rev E. (PG2.0) and take over maintainership.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Take over maintainership as well. Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).
Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested on my OMAP3 uEVM.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
fdtdec_get_addr_size() hard-codes the number of cells used to represent
an address or size in DT. This is incorrect in many cases depending on
the DT binding for a particular node or property (e.g. it is incorrect
for the "reg" property). In most cases, DT parsing code must use the
properties #address-cells and #size-cells to parse addres properties.
This change splits up the implementation of fdtdec_get_addr_size() so
that the core logic can be used for both hard-coded and non-hard-coded
cases. Various wrapper functions are implemented that support cases
where hard-coded cell counts should or should not be used, and where
the client does and doesn't know the parent node ID that contains the
properties #address-cells and #size-cells.
dev_get_addr() is updated to use the new functions.
Core functionality in fdtdec_get_addr_size_fixed() is widely tested via
fdtdec_get_addr_size(). I tested fdtdec_get_addr_size_auto_noparent() and
dev_get_addr() by manually modifying the Tegra I2C driver to invoke them.
Much of the core implementation of fdtdec_get_addr_size_fixed(),
fdtdec_get_addr_size_auto_parent(), and
fdtdec_get_addr_size_auto_noparent() comes from Thierry Reding's
previous commit "fdt: Fix fdtdec_get_addr_size() for 64-bit".
Based-on-work-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Dropped #define DEBUG at the top of fdtdec.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
On the LaCie boards netspace_max_v2 and net2big_v2, two internal hard
drives are available. Additionally on the d2net_v2 board, an extra hard
drive can be plugged via eSATA.
This patch updates CONFIG_SYS_IDE_MAXBUS and CONFIG_SYS_IDE_MAXDEVICE
accordingly for this boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch enables generic board support for the following
Kirkwood-based LaCie boards:
- Network Space v2 (Mini, Lite and Max).
- Internet Space v2.
- D2 Network v2.
- 2Big Network v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
CONFIG_FEC_DMA_MINALIGN is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
There is no need to undef the config options.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_ROM_UNIFIED_SECTIONS is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_SYS_GENERIC_BOARD is selected by mx6_common.h, so there is no
need to define it locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_CMD_FUSE and CONFIG_MXC_OCOTP are selected by mx6_common.h,
so there is no need to define them locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
We have CONFIG_MXC_OCOTP and CONFIG_CMD_FUSE in mx6_common.h,
discard duplicated macro definitions in board header files.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Define CONFIG_MACH_TYPE to allow non DT Linux boot.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Mainline CM-T3517 U-Boot environment size differs from that one
shipped with CM-T3517 boards.
Update environment size, to avoid backward compatibility issues.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
SBC-T3517 evaluation board has two Eth interfaces.
Enable network retry of another interface if the default if failed
or disconnected.
Add 'netretry=yes' in the default env. Setup relevant
timeout values in the board config file.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch changes a little bit the environment, current environment was broken
for a long time, and board don't as expected sometimes, on production systems
this is fixed adding boot script. I think it's time to change this to make a
system conformant environment and use generic distro configurations and
environment instead. We can use a boot script for the old way boot mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This allows transferring data directly to/from RAM. For example, one
could create a boot script that starts DFU on a RAM region, then once
DFU exits (which is under the control of the attached USB host, via a
USB bus reset), uses the code/data that was received over DFU.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Writing to files is a useful feature in general, so enable it everywhere.
The primary purpose is to make DFU useful on filesystems in addition to
raw devices.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
CONFIG_SYS_DFU_DATA_BUF_SIZE defines the size of chunks transferred
across USB. This doesn't need to be particularly large, since it doesn't
limit the overall transfer size.
CONFIG_SYS_DFU_MAX_FILE_SIZE is used to buffer an entire file before
writing it to a filesystem. This define limits the maximum file size that
may be transferred. Bump this up to 32MiB in order to support large
uncompressed kernel images.
Both of these buffers are dynamically allocated, and so the size of both
needs to be taken into account when calculating the required malloc
region size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 52a7c98a17 "tegra-common: increase malloc pool len by dfu mmc
file buffer size" updated the definition of CONFIG_SYS_MALLOC_LEN for
Tegra to take account of the DFU buffer size. However, this change had
no effect, since typical Tegra board config headers don't set the DFU-
related defines until after tegra-common.h is included. Fix this by
moving the affected conditional code to tegra-common-post.h, which is
included last. Also move the definition of SYS_NONCACHED_MEMORY since
it's a related and adjacent definition.
Fix the condition to test for the DFU feature, rather than specifically
MMC DFU support, so it applies in all cases.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable dwc3, dwc3-omap and PHY to get DWC3 functional in OMAP5
uEVM. Also enable support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:
4519668 mtd/nand/ubi: assortment of alignment fixes
This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.
Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
To reduce the size of the U-Boot image on the x600 board, lets enable
the THUMB mode. This reduces the overall size to less than 0x6000
bytes. Fitting it again in the onboard NOR flash.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board is equipped with a Micron NAND chip (MT29F1G08ABADAH4) that
needs 4-bit ECC. But the SPEAr600 only supports 1-bit HW ECC internally.
This patch enables the SW 4-bit BCH support for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove dm355evm, dm355leopard, dm365evm, dm6467evm, dvevm, ea20, schmoogie,
sffsdr, sonata.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Linux kernel can enumerate mmc sd as either mmcblk0 or mmcblk1.
But u-boot default environment assumes that sd always populates
as mmcblk0. With this the root fs is not being mounted when
mmc sd is enumerated as mmcblk1.
So use partuuid to update root= option in default environment.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All TI SoCs expect filesystem to be ext4, omap4_common is the only one
with ext3. move omap4 to ext4 so that we can start consolidating MMC
arguments.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To simplify and having a common default IP-setup on all B&R boards we
introduce an environment variable "brdefaultip" which does following.
Test if ${ipaddr} is empty, if yes it set's up some defaults:
- ipaddr : 192.168.60.1
- netmask : 255.255.255.0
- gatewayip: 192.168.60.254
- serverip : 192.168.60.254
This environment is ran from CONFIG_PREBOOT.
All other "tricks" are dropped.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[root@pollux dfu-util]# ./src/dfu-util -l
dfu-util 0.8
Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2014 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to dfu-util@lists.gnumonks.org
Found DFU: [0908:02d2] ver=0212, devnum=119, cfg=1, intf=0, alt=0, name="Linux", serial="UNKNOWN"
[root@pollux dfu-util]#
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fix corrupt line wraps in patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add extensions for the axm board:
- power on LED on power up
- press both recovery buttons on power up to enter
recovery mode
- detect 64 MiB and 128 MiB ramsize
- PHY rest at reboot because of ATMEL bug
- use siemens update concept
- add axm default environment
- set CONFIG_SPL_MAX_SIZE to 15k
Signed-off-by: Heiko Schocher <hs@denx.de>
Now that we have converted the pch_gbe driver to driver moel,
enable it on Intel Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit converts pch_gbe ethernet driver to driver model.
Since this driver is only used by Intel Crown Bay board, the
conversion does not keep the non-dm version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since E1000 driver has been converted to driver model, enable it
on Intel Crown Bay. But the Intel Topcliff GbE driver has not been
converted to driver model yet, disable it for now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add one more ethernet device node in the sandbox test device tree,
with name 'sbe5'. This is to support a new test case for testing
network device rotation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a PCI node to the device tree. This allows SPI flash and SATA to work
correctly. Also configure the video to come up correctly even though there
is no keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code allows using DFU defined mediums for storing data received via
TFTP protocol.
It reuses and preserves functionality of legacy code at common/update.c.
The update_tftp() function now accepts parameters - namely medium device
name and its number (e.g. mmc 1).
Without this information passed old behavior is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function allows writing via DFU data stored from fixed buffer address
(like e.g. loadaddr env variable).
Such predefined buffers are used in the update_tftp() code. In fact this
function is a wrapper on the dfu_write() and dfu_flush().
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds initial support for using tftp for downloading and
upgrading firmware on the device.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This change gives the ability to reuse the <tftp.h> header file by other
subsystems (like e.g. dfu).
Without this change compilation error emerges for the legacy update.c file.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for Terasic SoCkit, which is CycloneV based board.
The board can boot either from SD/MMC or QSPI. Ethernet is also
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
The CONFIG_OF_CONTROL and CONFIG_SPL_OF_CONTROL is always enabled
on Altera SoCFPGA, remove the unnecessary checks.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Now that MMC works in U-Boot add config distro command support to start
Linux in a standard fashion. One oddity here is that linux fails to load
when the fdt is relocated to above 512MB, so set fdt_high to make sure it's
loaded below that.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Rockchip boot ROM requires a particular file format for booting from SPI.
It consists of a 512-byte header encoded with RC4, some padding and then up
to 32KB of executable code in 2KB blocks, separated by 2KB empty blocks.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format. This allows booting from SPI flash on supported
machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Rockchip boot ROM requires a particular file format. It consists of
64KB of zeroes, a 512-byte header encoded with RC4, and then some executable
code.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rockchip SoCs require certain formats for code that they execute, The
simplest format is a 4-byte header at the start of a binary file. Add
support for this so that we can create images that the boot ROM understands.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
My original pinctrl patch operating using a peripheral ID enum. This was
shared between pinmux and clock and provides an easy way to specify a device
that needs to be controlled, even it is does not (yet) have a driver within
driver model.
Masahiro's new simple pinctrl gets around this by providing a
set_state_simple() pinctrl method. By passing a device to that call the
peripheral ID becomes unnecessary. If the driver needs it, it can calculate
it itself and use it internally.
However this does not solve the problem for peripheral clocks. The 'pure'
solution would be to pass a driver to the clock uclass also. But this
requires that all devices should have a driver, and a struct udevide. Also
a key optimisation of the clock uclass is allowing a peripheral clock to
be set even when there is no device for that clock.
There may be a better way to achive the same goal, but for now it seems
expedient to add in peripheral ID to the pinctrl uclass. Two methods are
added - one to get the peripheral ID and one to select it. The existing
set_state_simple() is effectively the union of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
there is a 2b board version of the aristainetos2
board. Differences to the v2:
- spi cs for the nor flash and display controller
changed
- some pinmux changes
- LED gpio settings changed
Signed-off-by: Heiko Schocher <hs@denx.de>
make the spi bus and the spi chipselect configurable
for the lg4573 driver. Use it on the aristainetos
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.
Boot Log:
U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)
CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
some small updates for the aristainetos boards:
- fix display timings for the aristainetos board
- fix pinmux for the aristainetos board
- fix pinmux for the aristainetos2 board
- fix default environment
Signed-off-by: Heiko Schocher <hs@denx.de>
* Add pmic pfuze3000 support, implement power_pfuze3000_init to be
used in power_init_board callback function.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds basic support including:
MMC, Serial console, TS4800 watchdog
The config use CONFIG_SKIP_LOWLEVEL_INIT as U-boot is used as a second
stage bootloader.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
cgtqmx6eval can be populated with a AR8035 or KSZ9031 depending on the
board revision.
Add Ethernet support.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Discard CONFIG_MX6 in mx6ul_14x14_evk.h, since it is already defined
in mx6_common.h.
Tested on mx6ul_14x14_evk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This patch removes the SPI support from the WRU-IV baseboard as its
not used at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Currently we need to build one U-boot image for each of the udoo
variants: quad and dual-lite.
By switching to SPL we can support all two variants with a single binary.
Based on the SPL for wandboard.
Tested with OpenELEC (Open Embedded Linux Entertainment Center)
on both boards.
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
It supports followings
- Card can operate with up to 4 QSGMII lane simultaneously
- Card can operate with up to 8 SGMII lane simultaneously
Add support of X-QSGMII-16PORT riser card.
This patch also take care of back-ward compatiblity with old SGMII rise cards
used on LS2085QDS Platform.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable CONFIG_CMD_GREPENV to allow search in env variables
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085 targets supports following UART console
LS2085AQDS UART0
LS2085ARDB UART1
LS2085ASim UART0
LS2085AEmu UART0
So update the bootargs as per the default console present at the target
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
