Commit Graph

6721 Commits

Author SHA1 Message Date
Chunhe Lan
0b2e13d9cc powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
2014-05-13 08:24:32 -07:00
Shaveta Leekha
652e29b4a0 board/b4qds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.

Reference for this code is taken from t4qds VID implementation.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-05-13 08:20:31 -07:00
Shaveta Leekha
4150f24290 board/freescale/common: ZM7300 driver
Adds Support for PowerOne ZM7300 voltage regulator.
This device is available on some Freescale Boards like B4860QDS
and has to be programmed to adjust the voltage on the board.

The device is accessible via I2C interface.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-05-13 08:20:31 -07:00
Masahiro Yamada
e7afb73b50 nand_spl: remove unused linker scripts u-boot-nand.lds
Commit 345b77ba removed some nand_spl boards but
it missed to delete linker scripts.

These linker scripts are not used now.

And one more fix:
amcc/acadia does not support nand_spl anymore, so remove
  #if !defined(CONFIG_NAND_U_BOOT) ... #endif

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2014-05-12 15:20:05 -04:00
Masahiro Yamada
6f2ed0e9fa cosmetic: delete misleading comment /* CONFIG_BOARDDIR */
CONFIG_BOARDDIR is not referenced in these linker scripts.
The comment /* CONFIG_BOARDDIR */ is misleading.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-05-12 15:20:05 -04:00
Masahiro Yamada
c42f56d96d blackfin: replace bfin_gen_rand_mac() with eth_random_addr()
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.

In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
2014-05-12 15:19:46 -04:00
Masahiro Yamada
da384a9d76 net: rename and refactor eth_rand_ethaddr() function
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.

For ex.
  is_zero_ether_addr()
  is_multicast_ether_addr()
  is_broadcast_ether_addr()
  is_valid_ether_addr();

So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.

Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-05-12 15:19:46 -04:00
Masahiro Yamada
8e2615752e bd_info: remove bi_barudrate member from struct bd_info
gd->bd->bi_baudrate is a copy of gd->baudrate.

Since baudrate is a common feature for all architectures,
keep gd->baudrate only.

It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
2014-05-12 15:19:45 -04:00
Tom Rini
f4617ef86d Merge branch 'tom' of git://git.denx.de/u-boot-x86 2014-05-09 18:48:26 -04:00
Masahiro Yamada
258060905e sandbox: move source files from board/ to arch/sandbox/
Prior to commit 33a02da0, all boards must have board/${BOARD}/
or board/${VENDOR}/${BOARD}/ directory.
Now this rule is obsolete.

It looks weird that sandbox defines "vendor" and "board" just for
meeting the old U-Boot directory structure.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
2014-05-09 14:51:14 -06:00
Simon Glass
75b3c3aa84 sandbox: Update and expand the README
Now that sandbox has a good base of features, the README is quite out of
date. Update it, and document the new features.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-05-09 14:47:57 -06:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Mateusz Zalega
41c2d60b3a ums: always initialize mmc before ums_disk_init()
In cases when MMC hadn't been initialized before, ie. by the user or other
subsystem, it was still uninitialized while UMS media capacity check,
leading to broken ums command.

UMS has to initialize resources it uses.

Tested on Samsung Goni.

Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
2014-05-05 08:21:47 +02:00
Mateusz Zalega
75504e9592 usb: dfu: fix boards wo USB cable detection
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.

I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.

Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.

Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.

CONFIG_USB_CABLE_CHECK was removed.

Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-05 08:00:28 +02:00
Tom Rini
5fcb084932 Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx 2014-04-25 15:06:51 -04:00
Tom Rini
b71bf4add6 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2014-04-25 14:57:58 -04:00
Tom Rini
080d897585 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-04-25 14:53:51 -04:00
Matthias Fuchs
e634c9dc7a ppc4xx: add support for new PMC440 revision with cleanup
This patch adds support for the new PMC440 hardware revision 1.4.
The board now uses Micrel KSZ9031 phys.

Add missing i2c initialization before reading bootstrap eeprom.

Fix a couple of coding style issues.

Make local functions static.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2014-04-24 13:15:53 +02:00
Heiko Schocher
eaf8c986d3 mpc83xx: add ids8313 support
add support for the ids8313 board.

CPU:   e300c3, MPC8313, Rev: 2.1 at 396 MHz, CSB: 132 MHz
I2C:   ready
SPI:   ready
DRAM:  128 MiB (DDR2, 32-bit, ECC off, 264 MHz)
Flash: 8 MiB
NAND:  128 MiB
Net:   TSEC0, TSEC1 [PRIME]

public key on NOR flash start

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2014-04-23 19:07:54 -05:00
Heiko Schocher
e7e9090108 powerpc, ids8247: create vendor board dir ids
create vendor board directory ids and move ids8247 board to it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2014-04-23 19:07:16 -05:00
Shaohui Xie
b6036993eb powerpc/T4QDS: add two stage boot of nand/sd
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:53 -07:00
Shaohui Xie
cb753850e8 powerpc/t4240: updated RCW and PBI for rev2.0
Updated the RCW for rev2.0 which uses new frequency settings as below:

Clock Configuration:
CPU0:1666.667 MHz, CPU1:1666.667 MHz, CPU2:1666.667 MHz, CPU3:1666.667 MHz,
CPU4:1666.667 MHz, CPU5:1666.667 MHz, CPU6:1666.667 MHz, CPU7:1666.667 MHz,
CPU8:1666.667 MHz, CPU9:1666.667 MHz, CPU10:1666.667 MHz, CPU11:1666.667MHz,
CCB:733.333 MHz,
DDR:933.333 MHz (1866.667 MT/s data rate) (Asynchronous), IFC:183.333 MHz
FMAN1: 733.333 MHz
FMAN2: 733.333 MHz
QMAN:  366.667 MHz
PME:   533.333 MHz

Remove workaround of IFC bus speed and SERDES A-006031 of rev1.0.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:53 -07:00
Shengzhou Liu
ef531c7357 board/t2080rdb: some update for t2080rdb
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
  ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
  previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Shengzhou Liu
4d66668300 board/t208xrdb: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Shengzhou Liu
b19e288f47 board/t208xqds: Add support of 2-stage NAND/SPI/SD boot
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Shaohui Xie
b0615f0bd2 powerpc/t1040rdb: added a break in switch case
There should be a break for case PHY_INTERFACE_MODE_SGMII, otherwise it
will fall into case PHY_INTERFACE_MODE_RGMII.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:52 -07:00
Prabhakar Kushwaha
18c0144542 board/t104xrdb: Add support of NAND, SD, SPI boot for T104xRDB
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
      - Add spl.c which defines board_init_f, board_init_r
      - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Prabhakar Kushwaha
c5dfe6ec58 board/b4qds:Add support of 2 stage NAND boot-loader
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
  - Add spl.c which defines board_init_f, board_init_r
  - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Zhao Qiang
6259e29134 T1040QDS/U-QE: Add u-qe support to t1040qds
Add u-qe support for t1040qds

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Tang Yuantian
5303a3dea9 mpc85xx: Add deep sleep support on T104xRDB
Add deep sleep support on T104xRDB platforms.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Tang Yuantian
48f6a9a2bf mpc85xx: Add deep sleep support on T1040QDS
Add deep sleep support on T1040QDS platform.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Prabhakar Kushwaha
55153d6c30 board/t104xrdb: Add support of CPLD
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.

This support of CPLD includes
 - files and register defintion
 - Commands to swtich alternate bank and default bank

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
York Sun
c60dee03c0 mpc85xx/T1040QDS_D4: Add DDR4 support
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Prabhakar Kushwaha
6b50f62cc4 board/b4860qds:Slow MDC clock to comply IEEE specs in PBI config
The MDC generate by default value of MDIO_CLK_DIV is too high i.e. higher
than 2.5 MHZ.  It violates the IEEE specs.

So Slow MDC clock to comply IEEE specs

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Alexander Graf
fa08d39517 PPC 85xx: Add qemu-ppce500 machine
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.

It also provides more PCI slots and is supposed to be enumerated by
device tree only.

This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:45 -07:00
Albert ARIBAUD
c9aab0f9dd Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-04-21 21:01:35 +02:00
Daniel Schwierzeck
538cf92c8c MIPS: drop incaip board
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-04-20 13:16:43 +02:00
Masahiro Yamada
36bf57b6fb arm: remove lubbock board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/lubbock/*
 - Remove include/configs/lubbock.h
 - Cleanup defined(CONFIG_LUBBOCK)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
03f2ecc2cb powerpc: remove MOUSSE board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/mousse/*
 - Remove include/configs/MOUSSE.h
 - Clean-up defined(CONFIG_MOUSSE)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
8b043e6dc2 powerpc: remove rsdproto board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/rsdproto/*
 - Remove include/configs/rsdproto.h
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
0ebf5f5c12 powerpc: remove RPXsuper board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/rpxsuper/*
 - Remove include/configs/RPXsuper.h
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
4fb3925ff8 powerpc: remove RPXClassic, RPXlite boards support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/RPXlite/*
 - Remove board/RPXClassic/*
 - Remove include/configs/RPXlite.h
 - Remove include/configs/RPXClassic.h
 - Clean-up defined(CONFIG_RPXCLASSIC)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
aa6e1e45cf powerpc: remove ADS860, FADS823, FADS850SAR, FADS860T support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
 - Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
   defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
 - Remove the entries from boards.cfg

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
b8a49bdaaa powerpc: remove genietv board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/genietv/*
 - Remove include/configs/GENIETV.h
 - Clean-up if defined(CONFIG_GENIETV)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
d6b11fd1f0 powerpc: remove MBX and MBX860T boards support
Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/mbx8xx/*
 - Remove include/configs/{MBX.h,MBX860T.h}
 - Clean-up if defined(CONFIG_MBX)
 - Move the entries from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
a146e8b189 powerpc: remove NX823 board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/nx823/*
 - Remove include/configs/NX823.h
 - Clean-up ifdef(CONFIG_NX823)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:29 -04:00
Masahiro Yamada
46d330a6ba kbuild: do not use $(BOARD) to specify exact object name
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-17 17:44:35 -04:00
Masahiro Yamada
cd8aa893b4 board: hidden_dragon: remove an unused source file
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Yusdi Santoso <yusdi_santoso@adaptec.com>
2014-04-17 17:44:35 -04:00
Masahiro Yamada
a839ce064b board: dave: delete unused source files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andrea Marson <andrea.marson@dave-tech.it>
2014-04-17 17:44:35 -04:00
Masahiro Yamada
d62bb61f7c board: prodrive: delete unused source files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2014-04-17 17:44:35 -04:00