The code flows through to the end of the function, so we don't need another
close() before this. Remove it.
Reported-by: Coverity (CID: 138504)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The license command isn't usually built and has a few problems:
- The rules to generate license.h haven't worked in a long time,
re-write these based on the bmp_logo.h rules.
- 'tok' is unused and the license text size has increased
- bin2header.c wasn't grabbing unistd.h to know the prototype for
read().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt. Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Some features are only useful or meaningful when the command line is
present. Ensure that these features are not compiled in when CONFIG_CMDLINE
is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These files do not need to be compiled when CONFIG_CMDLINE is disabled.
Update the Makefile to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When CONFIG_CMDLINE is disabled we need to remove all the command-line
code. Most can be removed by dropping the appropriate linker lists from the
images, but sub-commands must be dealt with specially.
A simple mechanism is used to avoid 'unused static function' errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Normally board_run_command() will handle command processed. But if for some
reason it returns then we should panic to avoid further processing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the link script to drop this code when not needed. This is only done
for two architectures at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new Kconfig option for the command line. This is enabled by default,
but when disabled it will remove the command line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All command functions should be static. Update the CBFS functions to follow
this rule.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation
timeout. This commit increases the timeout to fix the issue.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Return value of get_mc_boot_status() in case of failure is not necessary
to be -1.
So update the error condition check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Yao Yuan <yao.yuan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Return i2c mux to the default channel after accessing retimer.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_SYS_CONSOLE_IS_IN_ENV needs to be enabled, so we could set stdout
environment variable to specify the vga for the console output when
LCD/HDMI is connected to the boards.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The eSDHC could select to use platform clock or peripheral clock to
generate SD clock. The default selection is platform clock. So, fix
the clock frequency value that's calculated for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As phy_connect and phy_config are being called from DPAA2 driver.
Remove calling of mentioned function from board file.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch integrate DPAA2 ethernet driver existing PHY framework.
Call phy_connect and phy_config as per available DPMAC id defined
in SerDes Protcol.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The serdes protocol entries in Serdes table 1 for protocol
0x03, 0x33, 0x35 and in Serdes table 2 for protocols 0x45
and 0x47 are updated to reflect the entries in
current Reference Manual.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
msi-map properties are used to tell an OS how PCI requester IDs are
mapped to ARM SMMU stream IDs.
for all PCI devices discovered in a system:
-allocate a LUT (look-up-table) entry in that PCI controller
-allocate a stream ID for the device
-program and enable a LUT entry (maps PCI requester id to stream ID)
-set the msi-map property on the controller reflecting the
LUT mapping
basic bus scanning loop/logic was taken from drivers/pci/pci.c
pci_hose_scan_bus().
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The per-PCI controller LUT (Look-Up-Table) is a 32-entry table
that maps PCI requester IDs (bus/dev/fun) to a stream ID.
Add defines for the register offsets.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Put pci_get_hose_head() prototype in header so it is available to
external users, allowing them to find and iterate over all pci
controllers.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update comments around how stream IDs are partitioned.
Stream IDs allocated to PCI are no longer divided up by
controller, but are instead a contiguous range
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove stream ID partitioning support that has been made
obsolete by upstream device tree bindings that specify how
representing how PCI requester IDs are mapped to MSI specifiers
and SMMU stream IDs.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the compatible property values for QSPI and DSPI dts nodes
are changed in kernel, FSL_QSPI_COMPAT and FSL_DSPI_COMPAT
need to be updated too.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Structures are defined for PDB (Protocol Data Blcks) for various
operations. These structure will be used to add PDB data while
creating the PDB descriptors.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
CC: Ulises Cardenas <raul.casas@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When CAAM runs a descriptor and an error occurs, a non-zero
value is set in Output Status Register. The if condition should
check the status for a non-zero value.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins
polarity by setting IRQCR register, because AQR405 interrupt is low
active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable wuo config to accelerate coherent ordered writes for LS2080A
and LS2085A.
WRIOP IP is connected to RNI-20 Node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With commit 7985cdf we converted all systems except for the Layerscape
SoCs to the generic descriptor table based page table setup.
On the Layerscape SoCs however, we just provide an empty table stub
and do the setup ourselves. To reserve enough memory for the tables,
we need to override the default counting mechanism which would end up
with an empty table because we have no maps.
Fixes: 7985cdf
Reported-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch makes the following changes to the SR1500 board port:
- Update defconfig to support SPI NOR (use make savedefconfig).
- Increase SPI speed to a maximum of 100MHz for faster system
bootup.
- Change environment location, so that its not between SPL and
main U-Boot. This way the combined SPL / U-Boot image can
be used for updates.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch makes it possible that boards can define a board-specific env
size. This is used by the SR1500 SoCFPGA board port.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Move the inclusion of the common socfpga configuration file further
down in the sr1500 configuration, so that the socfpga_common.h can
check if environment is in SPI NOR and it's location is defined and
if it is not, define default location.
This fixes "arm: socfpga: Enabling U-Boot environment support in QSPI"
which introduced a minor warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Enabling the support of storing U-Boot environment
within serial NOR flash. By default, its still
store into SDMMC
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Add test into xhci_submit_control_message for usb requesttype in USB
vendor request being of standardized type. This fixes detection of
certain USB fixes, for example Ethernet, USB 3.0 port. Non standardized
requesttype in USB vendor request will be ignored.
Signed-off-by: Ted Chen <tedchen@realtek.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
