The MCAST_TFTP support requires that network drivers has mcast functon
implemented. This commit adds dummy keystone2_eth_bcast_addr() to meet
the requirement. As far as the driver doesn't use ALE and doesn't filter
any incoming packets, the function is empty.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When we return an error the usb core will print an error-message, so in this
case do not print anything.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The ci_udc driver request allocation assumes that the endpoint descriptor
pointer is set to retrieve the endpoint number, but that is only true
when the endpoint is enabled. This results in a NULL ptr dereference
which for me happens to return 0 value. This causes the EP0 request
struct to be returned for other endpoints. Some gadget drivers like
fastboot and USB MS work fine, but ethernet does not.
Really, the ci_udc driver is the oddball here doing this EP0 special
case handling Stephen added. All the other drivers alloc/free functions
are pretty much the same with the only variation being the size of the
private struct. This could all be consolidated to a common function.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
`mmc_initialize` might be called multiple times leading to the mmc-controllers
being initialised twice, and initialising the `mmc_devices` list head twice
which may lead to memory leaks.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the Armada A38x boot image. Not linked with the main U-Boot. With this
code addition and the serdes/PHY setup code, the Armada A38x support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion.
Note:
This code has undergone many hours (days!) of coding-style cleanup and
refactoring. It still is not checkpatch clean though, I'm afraid. As the
factoring of the code has so many levels of indentation that many lines
are longer than 80 chars.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The macro cpu_relax() is defined by several headers in different
ways.
arch/{arm,avr32,mips}/include/asm/processor.h defines it as follows:
#define cpu_relax() barrier()
On the other hand, include/linux/compat.h defines it as follows:
#define cpu_relax() do {} while (0)
If both headers are included from the same source file, the warning
warning: "cpu_relax" redefined [enabled by default]
is displayed.
It effectively makes it impossible to include <linux/compat.h>
from some sources. Drop the latter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This patch removes the wrl accessor function from the Marvell EHCI
driver by replacing it with the writel function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.
This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Recent versions of the fastboot tool will query the partition type before doing
an operation on a partition (such as erase, flash, etc). It will then submit
the operation as soon as the response for the partition type is received.
Usually, the MUSB controller will see that the partition type request return
status was read by the host at the very same time as the actual operation
request is submitted by the host. However, the operation will be read first
(int_rx is handled first in musb_interrupt) and after it is completed, the
fastboot USB gadget driver will send another return status. Hence, this happens
before the musb gadget framework has had a chance to handle the previous
acknowledgement that the host read the return status and dequeue the request.
The host will then usually empty the FIFO by the time musb_interrupt gets around
handling the return status acknowledgement (for the previous request, this is
still on the same musb_interrupt call), so no other interrupt is generated and
the most recent return status acknowledgement remains unaccounted for.
It will then be used as a response for the next command, and the proper response
for it will be delayed to the next command, and so on.
Dequeuing the previous IN request in the fastboot code ensures that no previous
return status remains. It is acceptable to do it since there is no callback to
it anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This avoids handling requests that have an error status or no data.
In particular, this avoids showing unnecessary error messages when the USB
gadget gets disconnected (e.g. with fastboot continue) and the fastboot USB
gadget driver sends an error back to the host (that has disconnected already).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Weak versions of board_usb_init and board_usb_cleanup are defined in common USB
host code, but it is also used for USB device gadgets, so we also need a weak
definition of it when there is no USB host enabled.
Both weak definitions do not conflict.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Remove LS102XA immap header inclusion from xhci fsl driver.
It removes redefinition warnings when built for platforms
other than LS102XA
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This USB Ethernet driver is quite widely use. Allow it to work with
CONFIG_DM_ETH enabled. Most of the code remains common but there is a new
packet receive flow which is handled specially.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support driver model in this driver. This uses the normal USB driver search
mechanism. Any EHCI controllers will be set up as they are found during
usb_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
In Linux USB_DEVICE() is used to declare a USB device by vendor/device ID.
We should follow the same convention in U-Boot. Rename the existing
USB_DEVICE() macro to U_BOOT_USB_DEVICE() and bring in the USB_DEVICE()
macro from Linux for use in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present USB Ethernet does not work with CONFIG_DM_ETH. Add driver model
support to this feature, so that it can work alongside other Ethernet
devices with driver model.
It was found that quite a bit of code is common in most of the USB Ethernet
drivers. Add this code to the common layer to reduce the amount of duplicate
code needed in USB Ethernet drivers when CONFIG_DM_ETH is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.
At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.
Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to find the full PCI address (bus, device and
function) for a PCI device. Add a function to provide this.
Adjust the existing code to use this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver is used by the Intel Minnowmax board. Convert it to driver model
so it can use the new Ethernet implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all PCI devices must be present in the device tree in order to
be used. Many or most PCI devices don't require any configuration other than
that which is done automatically by U-Boot. It is inefficent to add a node
with nothing but a compatible string in order to get a device working.
Add a mechanism whereby PCI drivers can be declared along with the device
parameters they support (vendor/device/class). When no suitable driver is
found in the device tree the list of such devices is consulted to determine
the correct driver. If this also fails, then a generic driver is used as
before.
The mechanism used is very similar to that provided by Linux and the header
file defintions are copied from Linux 4.1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add device-model support to the musb-host u-boot glue, note this only
adds device-model support to the musb-core glue code, it does not add
support for device-model to any of the SoC specific musb glue code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a musb_host_data struct to hold all the global data host related musb
data. This is a preparation patch for adding device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
