SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.
Call an arch specific function to take control of specific mdio lines at
runtime.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch tackles the time out problem which leads to break the
boot process, when loading file over nfs. The patch does two things.
First of all, we just ignore messages that arrive with a rpc_id smaller
then the client id. We just interpret this messages as answers to
formaly timed out messages.
Second, when a time out occurs we double the time to wait, so that we
do not stress the server resending the last message.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Marvell Dove also uses mvgbe as ethernet driver, therefore add support
for Dove to reuse the current driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Not all boards define an SOC. As a result, we can't depend on that.
This was introduced in 39f985536d
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
A pxelinux server setup for "default" menu is typically an x86 binary.
This does not work well with a mixed architecture setup. Extend the default
search to look for default-<arch>-<soc> and then default-<arch> before
falling back to just "default".
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
ontimeout is similar to default, but is the selection on menu timeout.
This is how cobbler sets a default. The label default is supposed to be
the default selection when <enter> is pressed. If both default and
ontimeout are set, last one parsed wins.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Menus with lots of entries and long append lines are hard to read.
Just show a numbered list using the label or name and make the choice
by entering the number.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The prompt flag is for displaying a "boot:" prompt in pxelinux. This
doesn't make sense for u-boot as we don't support the pxelinux command
interface. So we should just ignore prompt statements and always show the
menu if a menu is present.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Standard pxelinux servers will typically use a zImage rather than u-boot
image format, so fallback to bootz if bootm fails.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add support for value of -1 For localboot. A value of -1 means return to
u-boot prompt.
The localboot value is often 0, so we need to distinguish the value from
localboot being selected. A value of greater than or equal to 0 means
attempt local boot command.
If localboot is selected, we don't want to try other entries.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Get the MAC address using eth_getenv_enetaddr_by_index so that the MAC
address of ethact is used. This enables using the a NIC other than the
first one for PXE boot.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
When use checkpatch.pl to check network related patch, it will report
--->8---
WARNING: networking block comments don't use an empty /* line,
use /* Comment...
---<8---
So, add --ignore NETWORKING_BLOCK_COMMENT_STYLE into .checkpatch.conf
This will help to keep all driver include network related driver use
the same comment style
Signed-off-by: Bo Shen <voice.shen@atmel.com>
before writing the received buffer to nand, erase the nand
sectors. If not doing this, nand write fails. See for
more info here:
http://lists.denx.de/pipermail/u-boot/2013-June/156361.html
Using the nand erase option "spread", maybe overwrite
blocks on, for example another mtd partition, if the
erasing range contains bad blocks.
So a limit option is added to nand_erase_opts()
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- remove the builtin 'rootpath' spec (according to U-Boot project
policy) and require user provided environments to contain these
- rephrase the evaluation of the 'muster_nr' approach which allows to
quickly switch among several network boot setups (make the setting
transparent when empty, resulting in default DULG behaviour)
- reduce the ARP timeout for faster network boot
Signed-off-by: Gerhard Sittig <gsi@denx.de>
- use the default baudrate table for serial communication
- remove hostname/boofile/rootpath defines which were not referenced elsewhere
Signed-off-by: Gerhard Sittig <gsi@denx.de>
re-order the conditions which make the recovery system startup: combine
those conditions which were explicitly initiated (key press, software
request) and those which post-process error conditions (installer issues)
Signed-off-by: Gerhard Sittig <gsi@denx.de>
getenv() immediately after setenv() may perfectly legally return NULL, so
make sure to not deference an invalid pointer when creating diagnostic output
Signed-off-by: Gerhard Sittig <gsi@denx.de>
This patch enables CONFIG_SILENT_CONSOLE for EXYNOS5.
This patch also removes the hardcoding of UART port from
exynos5250 config.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support to the serial s5p driver.
At present disabling the serial console (from the device tree) crashes
U-Boot. Add checks for this case, so that execution can continue without
a serial console.
It also enables the serial_s5p driver recognize the silent_console option.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds the device node required for serial driver
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add required compatible information for s5p serial driver
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some Exynos5250 silicon may require 1.05v on the MIF to be stable, so to be
safe we can default to 1.05v instead of 1.00v. This can be set optimally later
in the boot process by the kernel.
The 0x6 value for 1.05v comes from the MAX77686 datasheet.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch updates the function board_i2c_init() to add support for both
FDT and non-FDT for I2C, and initialise the I2C channels.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move common flash write code into spi_flash_write_common().
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flag status register polling is required for micron 512Mb flash
devices onwards, for performing erase/program operations.
Like polling for WIP(Write-In-Progress) bit in read status register,
spi_flash_cmd_wait_ready will poll for PEC(Program-Erase-Control)
bit in flag status register.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no other call other than spi_flash_cmd_wait_ready(),
hence removed spi_flash_cmd_poll_bit and use the poll status code
spi_flash_cmd_wait_ready() itself.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the existing spi_flash_addr() for 3-byte addressing
cmd filling in write call.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Defined bank addr code on CONFIG_SPI_FLASH_BAR macro, to reduce the
size for existing boards which has < 16Mbytes SPI flashes.
It's upto user which has provision to use the bank addr code for
flashes which has > 16Mbytes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>