Commit Graph

595 Commits

Author SHA1 Message Date
Bin Meng
b06862b9d8 x86: quark: Add USB PHY initialization support
USB PHY needs to be properly initialized per Quark firmware writer
guide, otherwise the EHCI controller on Quark SoC won't work.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
31b5aebd5e x86: Convert to use driver model pci on quark/galileo
Move to driver model pci for Intel quark/galileo.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
316fd3920f x86: Enable PCIe controller on quark/galileo
Quark SoC holds the PCIe controller in reset following a power on.
U-Boot needs to release the PCIe controller from reset. The PCIe
controller (D23:F0/F1) will not be visible in PCI configuration
space and any access to its PCI configuration registers will cause
system hang while it is held in reset.

Enable PCIe controller per Quark firmware writer guide.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
aa09505ba1 x86: quark: Avoid chicken and egg problem
If we convert to use driver model pci on quark, we will encounter
some chicken and egg problems like below:

- To enable PCIe root ports, we need program some registers on the
  message bus via pci bus. With driver model, the first time to
  access pci bus, the pci enumeration process will be triggered.
  But without first enabling PCIe root ports, pci enumeration
  just hangs when scanning PCIe root ports.
- Similar situation happens when trying to access GPIO from the
  PCIe enabling codes, as GPIO requires its block base address
  to be assigned via a pci configuration register in the bridge.

To avoid such dilemma, replace all pci calls in the quark codes
to use the local version which does not go through driver model.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
5750e5e29a x86: quark: Optimize MRC execution time
Intel Quark SoC has a low end x86 processor with only 400MHz
frequency. Currently it takes about 15 seconds for U-Boot to
boot to shell and the most time consuming part is with MRC,
which is about 12 seconds. MRC programs lots of registers on
the SoC internal message bus indirectly accessed via pci bus.

To speed up the boot, create an optimized version of pci config
read/write dword routines which directly operate on PCI I/O ports.
These two routines are inlined to provide better performance too.
Now it only takes about 3 seconds to finish MRC, which is really
fast (4 times faster than before).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Bin Meng
5bc60d5a44 x86: coreboot: Convert to use more dm drivers
Move to driver model for RTC, USB and ETH on coreboot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Simon Glass
548fb8777d x86: panther: Add PCI and video configuration
Add a PCI node to the device tree. This allows SPI flash and SATA to work
correctly. Also configure the video to come up correctly even though there
is no keyboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-09-09 07:48:03 -06:00
Simon Glass
6e474eab44 exynos: x86: dts: Add tpm nodes to the device tree for Chrome OS devices
Add a TPM node to the various Chromebooks so that driver can be converted to
driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-08-31 07:57:28 -06:00
Bin Meng
a1f1582b73 x86: crownbay: Support Topcliff integrated pci uart devices with driver model
In order to make a pci uart device node to be properly bound to its
driver, we need make sure its parent node has a compatible string
which matches a driver that scans all of its child device nodes in
the device tree.

Change all pci bridge nodes under root pci node to use "pci-bridge"
compatible driver, as well as corresponding <reg> properties to
indicate its devfn. At last, adding "u-boot,dm-pre-reloc" to each
of these nodes for driver model to initialize them before relocation.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:17 -07:00
Bin Meng
4dd02a752c x86: crownbay: Enable on-board SMSC superio keyboard controller
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.

In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:16 -07:00
Simon Glass
86645c8932 x86: minnowmax: Correct pad-offset value for host_en1
This should be 0x250, not 0x258. Fix it.

Reported-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:14 -07:00
Simon Glass
cce7e0fa2b x86: minnowmax: Add access to GPIOs E0, E1, E2
These GPIOs are accessible on the pin header. Add pinctrl settings for them
so that we they can be adjusted using the 'gpio' command.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:14 -07:00
Saket Sinha
bccdf1de75 x86: Add DSDT table for supporting ACPI on QEMU
The DSDT table contains a bytecode that is executed by a driver in the kernel.

Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Tested with QEMU '-M q35'
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:14 -07:00
Saket Sinha
e94019ede7 x86: Add ACPI table support to QEMU
This patch mainly adds ACPI support to QEMU.
Verified by booting Linux kernel on QEMU Q35.

Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Minor whitespace fixes and dropped mention of i440FX in commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:14 -07:00
Saket Sinha
867bcb63e7 x86: Generate a valid ACPI table
Implement write_acpi_table() to create a minimal working ACPI table.
This includes writing FACS, XSDT, RSDP, FADT, MCFG, MADT, DSDT & SSDT
ACPI table entries.

Use a Kconfig option GENERATE_ACPI_TABLE to tell U-Boot whether we need
actually write the APCI table just like we did for PIRQ routing, MP table
and SFI tables. With ACPI table existence, linux kernel gets control of
power management, thermal management, configuration management and
monitoring in hardware.

Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tidied up whitespace and aligned some tabs:
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:13 -07:00
Bin Meng
c78dfb4fd2 x86: superio: Add keyboard controller support to smsc_lpc47m driver
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:12 -07:00
Bin Meng
fa6af7b4e0 x86: baytrail: Remove the fsp_init_phase_pci() call
It turns out that calling fsp_init_phase_pci() in arch_misc_init()
is subject to break pci device drivers as with driver model, when
the bus enumeration happens is not deterministic.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:12 -07:00
Bin Meng
090290f97b x86: queensbay: Move unprotect_spi_flash() to arch_misc_init()
With dm pci conversion, pci config read/write in unprotect_spi_flash()
silently fails as at that time dm pci is not ready and bus enumeration
is not done yet. Actually we don't need to do this in that early phase,
hence we delay this call to arch_misc_init().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:12 -07:00
Bin Meng
48aa6c2614 x86: fsp: Add comments about U-Boot entering start.S twice
Add some comments in start.S for the fact that with FSP U-Boot
actually enters the code twice. Also change to use fsp_init()
and fsp_continue for accuracy.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:11 -07:00
Bin Meng
57b10f59b7 x86: fsp: Enlarge the size of malloc() pool before relocation
After fsp_init() returns, the stack has already been switched to a
place within system memory as defined by CONFIG_FSP_TEMP_RAM_ADDR.
Enlarge the size of malloc() pool before relocation since we have
plenty of memory now.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:11 -07:00
Bin Meng
5fb0151697 x86: baytrail: Support multiple microcode copies
Intel FSP has the capability to walk through the microcode blocks
which are passed as the TempRamInit() parameter from U-Boot and
finds the most appropriate microcode which is suitable for the cpu
on which it is running. Now we've seen several steppings for Intel
BayTrail series processors, adding those microcodes to the Intel
BayleyBay and MinnowMax board device tree files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:09 -07:00
Bin Meng
5c113ff79c x86: baytrail: Add microcode for BayTrail-I D0 stepping
This commit adds the microcode blob for BayTrail-I D0 stepping,
CPUID signature 30679h.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-26 07:54:09 -07:00
Bin Meng
8744bef5a1 x86: kconfig: Hide "System tables" for coreboot
When booting as a coreboot payload, we don't need write any
configuration tables as coreboot does that for us.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:08 -07:00
Bin Meng
d2f56f46fe x86: kconfig: Hide "System tables" for EFI
Instead of hiding each menu entries under "System tables" for EFI,
hide the main menu completely.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:07 -07:00
Bin Meng
a25bc78e2f x86: coreboot: Allow >=4GiB memory bank size
Some platforms may have >=4GiB memory, so we need make U-Boot report
such configuration correctly when booting as the coreboot payload.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:07 -07:00
Bin Meng
c17ca6b5cd x86: Remove calculate_relocation_address()
Now that we have generic routine to calculate relocation address,
remove the x86 specific one which is now only used by coreboot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:07 -07:00
Bin Meng
52b778603b x86: coreboot: Correctly report E820 types
coreboot has some extensions (type 6 & 16) to the E820 types.
When we detect this, mark it as E820_RESERVED.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:07 -07:00
Bin Meng
89b870814c x86: coreboot: Increase memrange entry number to 32
Increase lib_sysinfo memrange entry number to 32 to sync with coreboot.
This allows a complete E820 table to be reported to the kernel, as on
some platforms (eg: Bayley Bay) having only 16 entires does not cover
all the memory ranges.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-26 07:54:06 -07:00
Simon Glass
ef910819c5 x86: minnowmax: Define and enable interrupt setup
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:14 -06:00
Simon Glass
052e34b363 x86: Return -1 when reading a PCI config register fails
This can fail for internal reasons, so return a sensible value rather than
a random one.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:13 -06:00
Simon Glass
ecf674b772 x86: Drop FSP error defines and use EFI instead
Now that we have an efi.h header we can use that for FSP error defines.
Drop the FSP ones.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:13 -06:00
Bin Meng
ecfeadabb7 x86: Set APs' req_seq to the reg number from device tree
Multiple APs are brought up simultaneously and they may get the same
seq num in the uclass_resolve_seq() during device_probe(). To avoid
this, set req_seq to the reg number in the device tree in advance.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-14 09:50:12 -06:00
Simon Glass
7399515d25 x86: Show the un-relocated IP address in exceptions
When trying to figure out where an exception has occured, the relocated
address is not a lot of help. Its value depends on various factors. Show
the un-relocated IP as well. This can be looked up in System.map directly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:12 -06:00
Simon Glass
f0c7d9c746 x86: Switch to using generic global_data setup
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.

Drop the unneeded code and adjust the hooks in board_f.c to cope.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:10 -06:00
Simon Glass
2db9374561 x86: Move the GDT into global_data
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:10 -06:00
Simon Glass
93afae5d05 x86: Remove init_gd() function
This is declared but no-longer exists. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
c8896ee481 x86: baytrail: Support running as an EFI payload
We should not fiddle with interrupts or the FSP when running as an EFI
payload. Detect this and skip this code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
46f8efee70 x86: baytrail: Tidy up interrupt and FSP init
We should signal to the FSP that PCI enumeration is complete. Perform this
task in a suitable place.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
7e4be120e8 x86: Allow pirq_init() to return an error
This function can fail. In this case we should return the error rather than
swallowing it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
412400abaa x86: Split out fsp_init_phase_pci() code into a new function
This code may be useful for boards that use driver model for PCI.

Note: It would be better to have driver model automatically call this
function somehow. However for now it is probably safer to have it under
board control.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Simon Glass
9e3ff9c2b4 x86: Tidy up the PIRQ routing code a little
This code could use a little tightening up. There is some repetition and
an odd use of fdtdec_get_int_array().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:21 -06:00
Bin Meng
da60fb7934 x86: fsp: Do not assert VPD_IMAGE_REV when DEBUG
When using different release version of Intel FSP, the VPD_IMAGE_REV
is different (ie: BayTrail Gold 3 is 0x0303 while Gold 4 is 0x0304).
Remove the asserting of this so that U-Boot does not hang in a debug
build.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-08-14 03:24:21 -06:00
Andrew Bradford
f3b84a3032 x86: baytrail: Configure FSP UPD from device tree
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.

Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.

Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-14 03:24:21 -06:00
Simon Glass
bbbe55f6f2 x86: Enable debug UART for Minnowmax
Enable the debug UART and emit a single 'a' early in the init sequence to
show that it is working.

Unfortunately the debug UART implementation needs a stack to work. I cannot
seem to remove this limitation as the absolute 'jmp %eax' instruction goes
off into the weeds.

So this means that the character output cannot be any earlier than
car_init_ret, where memory is available for a stack.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-08-06 07:44:30 -06:00
Simon Glass
eeae510007 x86: qemu: Support operation as an EFI payload
Disable a few things which interfere with the EFI init. This allows QEMU to
to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:08 -06:00
Simon Glass
b4302582f3 x86: baytrail: Support operation as an EFI payload
Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:08 -06:00
Simon Glass
8e36650875 x86: Add helper code for running from EFI
When U-Boot is running from EFI some of the x86 init is replaced with
EFI-specific init. For example, since DRAM has already been set up, we only
need to find it, not init it. Add these functions so that boards can easily
allow booting from EFI if required.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:08 -06:00
Simon Glass
e49cceac61 x86: Handle running as EFI payload
When U-Boot runs as an EFI payload it needs to avoid setting up the CPU
again. Also U-Boot currently does not handle interrupts for many devices, so
run with interrupts disabled.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:08 -06:00
Simon Glass
42fde30500 x86: Add support for passing tables into U-Boot
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.

Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00
Simon Glass
96a8d409a7 efi: Add 64-bit payload support
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.

Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:44:07 -06:00