Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 in Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some boards may want to show the SKU ID or other information obtained at
runtime. Allow this to come from sysinfo. The board can then provide a
sysinfo driver to provide it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The U_BOOT_CMDREP_COMPLETE() macro produces a build error if CONFIG_CMDLINE
is not enabled. Fix this by updating the macro to provide the 'repeatable'
arugment in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature was dropped from U-Boot some time ago:
f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")
However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).
I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.
Re the points mentioned in the removal commit:
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
Which uclass is this?
2) Technically there is no real hardware user for this API to
use in the source tree.
I do want coral (at least) to support this.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
This new patch only mentions write-protect being on or off, rather than
the actual mechanism.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is special in that it is used for testing and it does not match
any particular target architecture. Allow it to load an image from any
architecture, so that 'bootm' can be used as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow referencing a CBFS file in the flashmap, so that it is possible to
boot from coreboot, where files are not available from binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports compressed filed. Add support for reading this
information so that the correct decompression can be applied. The
decompression itself is not implemented in CBFS.
Signed-off-by: Simon Glass <sjg@chromium.org>
The file traversal functions currently use a single global CBFS. In some
cases we need to access multiple CBFSs to obtain different files. Add new
functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases CBFS does not start with a header but is just a collection
of files. It is possible to support this so long as the size of the CBFS
is provided.
Update the cbfs_init_mem() function to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When U-Boot is booted from coreboot the SMBIOS tables are written by
coreboot, not U-Boot. The existing method of updating the BIOS version
string does not work in that case, since gd->smbios_version is only set
when U-Boot writes the tables.
Add a new function which allows the version to be updated by parsing the
tables and writing the string in the correct place. Since coreboot
provides a pointer to the SMBIOS tables in its sysinfo structure, this
makes it easy to do the update.
Signed-off-by: Simon Glass <sjg@chromium.org>
CBFS now supports attributes for things that cannot fit in the header as
originally conceived. Add the structures for these.
Also rename attributes_offset to something shorter, to ease code
readability.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the eMMC device does not have an alias so it appears after
the SD card which is device 1. There is no device 0 which is odd.
Make the eMMC device be the first one. Update the boot script to use the
new device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dfu_free_entities() invoking dfu_free_entity_sf() has let to segementation
faults due to double freeing the same device.
spi_flash_free() is not relevant for the driver model but exists only for
compatibility with old drivers.
We must not remove any device here:
* The device may still be referenced.
* We don't want to have to probe again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBdZYURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreb2rQgAyr1rufrt1UGjZlVjk0HtqX0sdmcOoE4e
6NIuatWXPcP2QR93O9zeGgf/yqNIf3lVIa6Cy3baJBfP6fceZ8B24/xgKKEauPFf
g99sec+q7LPL/oigajXIaWorFXK/NDRtQcSIQFu/EmvCmi0m8Iu0HKFa7YBqa7dc
YdhGnJZZOdYuQmlKewq9q4cIr6qNtTZczsozt4PNZVgB2lKusBNyKRPZErNEFiN6
7A56bb8tcfWgGXenKVTUUcyjWRXM2tt4QtrPFedZsF6cLa8D5v4MfWMs0QBRFl/u
fMzxyeb46x0wsYBNqIBOC7DQWaU/ZeFlr5mQObIH0ypdcsUnEX98sw==
=Ld3P
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26mar21-take2' of git://git.denx.de/u-boot-dm into next
dtoc support for of-platdata-inst
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
Add a warning to each of these functions so that people do not attempt to
use them outside driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Make use of the new priv/plat data region if enabled. This is implemented
as a simple offset from the position set up by dtoc to the new position.
So long as all access goes through dm_priv_to_rw() this is safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the device priv/data data allocated by dtoc is stored in the
data section along with other variables. On some platforms it is better
to allocate space for it separately, e.g. if SPL is running from read-only
memory.
Create a new space with the same size as that allocated by dtoc, ready for
use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When of-platdata-inst is active, use the flags in the new udevice_rt
table, dropping them from the main struct udevice. This ensures that the
latter is not updated at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when driver model needs to change a device it simply updates
the struct udevice structure. But with of-platdata-inst most of the fields
are not modified at runtime. In fact, typically only the flags need to
change.
For systems running SPL from read-only memory it is convenient to separate
out the runtime information, so that the devices don't need to be copied
before being used.
Create a new udevice_rt table, similar to the existing driver_rt. For now
it just holds the flags, although they are not used in this patch.
Add a new Kconfig for the driver_rt data, since this is not needed when
of-platdata-inst is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the i2c emulators require access to the devicetree, which is
not possible (by design) with of-platdata.
Add a way for drivers to record the of-platdata index of their emulator,
so that we can still find the emulator.
This allows i2c emulation to work with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function finds a device by its driver_info index. With
of-platdata-inst we do not use driver_info, but instead instantiate
udevice records at build-time.
However the semantics of using the function are the same in each case:
the caller provides an index and gets back a device.
So rename the function to device_get_by_ofplat_idx(), so that it can be
used for both situations. The caller does not really need to worry about
the details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is now only used in a test. Drop it. Also drop
DM_DRVINFO_GET() which was the only purpose for having the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to allow SoCs to create their own drivers for this so that they
can use their own of-platdata structs. To minimise code duplication,
export the driver operations and the ofdata_to_plat() setup function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When dt-structs.h is used, include the dt-decl.h header as well, so that
these declarations are available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Setup will always occur before ExitBootServices(). So eliminate
EFI_SETUP_AFTER_BOOTTIME_EXIT. Put the SetVirtualAddressMap() test into a
separate class so that we can execute it last.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The ESRT is initialised during efi_init_objlist after
efi_initialize_system_table().
The ESRT is recreated from scratch at the following events:
- successful UpdateCapsule;
- FMP instance install.
The code ensures that every ESRT entry has a unique fw_class value.
Limitations:
- The ESRT is not updated if an FMP instance is uninstalled;
- the fields image_type and flags are in the current implementation left
undefined. Setting these values will require a per-platform function
that returns the image_type/flags as a function of the image fw_class.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Alexander Graf <agraf@csgraf.de>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Remove two EFI_CALL() indirections.
Move ESRT GUID in efidebug's list of GUIDs.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now we install EFI_LOAD_FILE2_PROTOCOL to load an initrd
unconditionally. Although we correctly return various EFI exit codes
depending on the file status (i.e EFI_NO_MEDIA, EFI_NOT_FOUND etc), the
kernel loader, only falls back to the cmdline interpreted initrd if the
protocol is not installed.
This creates a problem for EFI installers, since they won't be able to
load their own initrd and continue the installation. It also makes the
feature hard to use, since we can either have a single initrd or we have
to recompile u-boot if the filename changes.
So let's introduce a different logic that will decouple the initrd
path from the config option we currently have.
When defining a UEFI BootXXXX we can use the filepathlist and store
a file path pointing to our initrd. Specifically the EFI spec describes:
"The first element of the array is a device path that describes the device
and location of the Image for this load option. Other device paths may
optionally exist in the FilePathList, but their usage is OSV specific"
When the EFI application is launched through the bootmgr, we'll try to
interpret the extra device path. If that points to a file that exists on
our disk, we'll now install the load_file2 and the efi-stub will be able
to use it.
This opens up another path using U-Boot and defines a new boot flow.
A user will be able to control the kernel/initrd pairs without explicit
cmdline args or GRUB.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A following patch introduces a different logic for loading initrd's
based on the EFI_LOAD_FILE2_PROTOCOL.
Since similar logic can be applied in the future for other system files
(i.e DTBs), let's add some helper functions which will retrieve and
parse file paths stored in EFI variables.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
On the following patches we allow for an initrd path to be stored in
Boot#### variables. Specifically we encode in the FIlePathList[] of
the EFI_LOAD_OPTIONS for each Boot#### variable.
The FilePathList[] array looks like this:
kernel - 0xff - VenMedia(initrd GUID) - initrd1 - 0x01 initrd2 - 0xff
So let's add the relevant functions to concatenate and retrieve a device
path based on a Vendor GUID.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reformat function descriptions.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
LS1028A-QDS has CONFIG_SPI_FLASH_SST and CONFIG_SPI_FLASH_EON defines
present in header. Move these entries from header to defconfigs.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is now safe to remove Flexspi configs NXP_FSPI_FLASH_SIZE and
NXP_FSPI_FLASH_NUM options from headers as they are no longer used by
driver anymore.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The name of the define must indicate 'Asynchronous', so 'ASYNC' is more
appropriate. AYSNC is probably a typo, and checkpatch script is throwing
a warning if this is set in the board include files.
It is save to change this now as none of the existing designs is using it
so far, but we will use it in our design it help to make IFC settings
more transparent.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When OF_PLATDATA_INST is enabled we don't need to create the uclass list.
Instead we just need to point to the existing list. Update the code
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add macros which work with instantiated devices and uclasses, as created
at build time by dtoc. Include variants that can be used in data
structures.
These are mostly used by dtoc but it is worth documenting them fully for
the occasional case where they might come up in user code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present linker lists are designed for use in code. They make use of
statements within expressions ({...}), for example.
It is possible to generate a reference to a linker_list entry that can
be used in data structures, where such features are not permitted. It
requires that the reference first be declared as extern. In other
words the existing macro needs to be split into two parts.
Add new macros to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for generating a file containing uclass instances. This avoids
the need to create these at run time.
Update a test uclass to include a 'priv_auto' member, to increase test
coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Typically dtoc can detect the header file needed for a driver by looking
for the structs that it uses. For example, if a driver as a .priv_auto
that uses 'struct serial_priv', then dtoc can search header files for the
definition of that struct and use the file.
In some cases, enums are used in drivers, typically with the .data field
of struct udevice_id. Since dtoc does not support searching for these,
add a way to tell dtoc which header to use. This works as a macro included
in the driver definition.
Signed-off-by: Simon Glass <sjg@chromium.org>
