libretech-cc being the main device tested with CONFIG_VIDEO_MESON, let's
enable it by default.
Also enable:
- CONFIG_SYS_WHITE_ON_BLACK for prettiness
- CONFIG_VIDEO_DT_SIMPLEFB for framebuffer sharing with kernel
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
With the recent addition of the meson VPU driver, enable the following
config entries by default for meson-64 targets: CONFIG_CONSOLE_MUX,
CONFIG_SYS_CONSOLE_IS_IN_ENV.
This allows outputting the console via video if CONFIG_VIDEO_MESON is
selected.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable USB host controllers for Amarula A64-Relic board,
the respective nodes are already present in DTS.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch enables Falcon Mode by default and updates the README
file to show instructions on how to run from the micro SD card
or eMMC. This patch also enables fatwrite to help assist with
writing the 'args' to the microSD card.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the updated device trees in place, this patch enables
DM_USB which uses several regulators also enabled with this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC booting wasn't previously fitting into the codespace.
This patch enables MMC booting from the baseboard by reducing
some DM overhead during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch converts the warp7 and warp7_bl33 board ports over to using the
DM PMIC model.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Switches on the IMX7 pinctrl driver for the warp7 and warp7_bl33 ports,
necessary to convert over to DM for this board.
It is necessary to switch on pinctrl and GPIO in one go.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds DT file hooks for imx7s-warp.dtb to the warp7 and
warp7_bl33 builds.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT.
The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK.
Note: SPL FIT could not support secure boot chain, because i.MX8/8X
only support i.MX container format. This container format has
not been upstreamed, so we use FIT for now. When SPL container
supported, we could switch to that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The defconfig already use most features implied by distro defaults.
Make sure we enable all features required by distro boot by making
use of CONFIG_DISTRO_DEFAULTS.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The colibri_imx7_defconfig is for Colibri iMX7 raw NAND devices.
Hence DFU for NAND is more useful then for MMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Access to CAAM in non-secure mode must be enabled by the boot
loader first. The U-Boot CAAM driver enables access to CAAM in
non-secure mode by default. Hence enable the CAAM driver to
allow Linux accessing CAAM directly. This prevents error
messages like the following on Linux boot:
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that device tree is in place use DM_MMC for Colibri iMX7
devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use OF_SEPARATE as suggested by the build system.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use DM and device trees for raw NAND devices by default. This
fixes -74 NAND read errors since it makes sure the ECC settings
are the same as used in Linux and our downstream U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
I'm working on getting OpenBSD to run on the Atmel SAMA5D3 Xplained.
OpenBSD uses an EFI bootloader, which requires the "load" command to
work, since "fatload" doesn't initialize the EFI memory addresses
properly. To get "load" on the SAMA5D3 version of U-Boot, I propose
adding the CONFIG_CMD_FS_GENERIC option.
Signed-off-by: Greg Czerniak <greg@czerniak.info>
A few platforms recently added in CONFIG_DFU_MMC under include/configs
rather than via the defconfig, update them.
Signed-off-by: Tom Rini <trini@konsulko.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Join the party of some ARM boards and drop more
items from include/configs/xxx.h.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no i2c connected in base DT that's why disable I2C commands.
Also remove zynq_zybo which is not needed now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
Zynq mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
ZynqMP mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable ISSI flash for platforms. Xilinx reference boards are also used
internally with different flash part to increase coverage that's why
enable also ISSI parts for all these boards even if that board is
released only with one part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enable net configs for zc1275 board.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
