* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Needed for redundant environment for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
i2c_probe() is changed to reinit the i2c bus upon read failure.
This is naturally the case upon i2c bus probing.
Also, some printf messages upon read failure are removed. As they
would interfere with the "i2c probe" command.
Additionally, i2c_set_bus_speed() now returns 0, so that the
"i2c speed" command can be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Add support for the M41T82 RTC to the m41t62 driver. The only
difference that needs to be handled by this driver, is to
clear the HT (Halt Update) bit upon reset. This bit is not
used on the M41T62, so its save to clear this bit always.
The M41T82 support will be used by the X600 (SPEAr600)
board support.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
On x600 (SPEAr600) U-Boot is appended to U-Boot SPL. Both images are
created using mkimage (crc etc), so that the ROM bootloader can check
its integrity. Padding needs to be done to the SPL image (with
mkimage header) and not the binary. Otherwise the resulting image
which is loaded/copied by the ROM bootloader to SRAM doesn't fit.
The resulting image containing both U-Boot images is called u-boot.spr.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).
Signed-off-by: Stefan Roese <sr@denx.de>
This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).
Signed-off-by: Stefan Roese <sr@denx.de>
raise() likes to call printf() if it is available, but in SPL builds it
either is not available, or adds a large chunk to the resulting image
size.
So don't call it even if it is available.
This change reduces SPL size from 10KB to 6.3KB on hawkboard, for
example, using generic relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
In SPEAr, some of the configuration flags eg. CONFIG_SPEAR_EMI, were given value
"1", which isn't required. Define the flags without assigning any value
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When CONFIG_MTD_NAND_VERIFY_WRITE is defined, nand driver read back the data
everytime it writes. This process unnecessarily slows down the nand access.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_SYS_FLASH_EMPTY_INFO macro to enable reporting of empty sector
information through flinfo command.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The below text is copy pasted from README
- CONFIG_SYS_MONITOR_BASE:
Physical start address of boot monitor code (set by
make config files to be same as the text base address
(TEXT_BASE) used when linking) - same as
CONFIG_SYS_FLASH_BASE when booting from flash.
This patch corrects the definition of CONFIG_SYS_MONITOR_BASE and sets it to
TEXT_BASE
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables flash protection(lock/unlock) for CFI devices.
This is necessary because the Parallel NOR flash connected on the spear
boards, M28W64, can be locked/unlocked on a sector basis. Moreover, all its
sectors are in locked state at reset and these have to be unlocked explicitly
before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable data cache with 1:1 mapping of DDR to enable fast file
transfer over tty which was doing lot of copy.
This feature is enabled only for flashing operation i.e. when
CONFIG_SPEAR_USBTTY is enabled.
This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation
boards.
Following figures show an estimate on the performance improvements. The
test setup was a Linux host (not Windows) and involved measurement of
only binary transfer time, through kermit. The flash erase and flash
copy time would be unaffected by these patches.
Another thing is this that the timings remained more or less same across
ARM9 and Cortex based devices, hence reporting only one of the cases.
Before Enhancements
===================
$ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m41.228s
user 0m0.002s
sys 0m0.064s
After Enhancements
==================
$ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m5.441s
user 0m0.001s
sys 0m0.001s
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enabling autoneg avoids situation on few phys with fixed configuration. For
example, in one situation, nfs boot timed out when phy configuration is 100Mbps.
In another situtation, when traffic is directed to SPEAr, either thru
cross-cable or thru switch, the TFTP or DHCP command in u-boot starts to timeout
very often.
When Autoneg is ON, same phys started working perfectly.
Reported-by: Deepak Sikri <deepak.sikri@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the UDC and usb-console support only for usbtty
configurations
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the support for usb high speed device for spear platform SOCs
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch modifies the default environment variables as:
1. Default bootargs:
- console=ttyAMA0,115200
- For environment present in NOR flash
root=/dev/mtdblock3
- For environment present in NAND flash
root=/dev/mtdblock7
- Removes "mem=" option
2. Introduces CONFIG_EXTRA_ENV_USBTTY as default usbtty env var even when usbtty
is not selected
3. Add default definitions for nfsboot and ramboot
4. Add a new default environment variable(CONFIG_EXTRA_ENV_UNLOCK) for SPEAr310
and SPEAr320
Signifacance of CONFIG_EXTRA_ENV_USBTTY:
This environment variable is important for flashing utility to work. So if
somebody accidently erases the env sector then also this variable must be
preserved so that flashing utility functions properly.
Signifacance of CONFIG_EXTRA_ENV_UNLOCK:
This env variable is read by the cfi driver to unlock all flash sectors. This
is necessary because the Parallel NOR flash connected on the spear310 and
spear320 boards, M28W64, has all its sectors in locked state at reset and these
have to be unlocked explicitly before being erased or written.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr doesn't need CONFIG_SYS_HZ_CLOCK. This commit removes it.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.
SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ethaddr can be optionally read from i2c memory. So, chip_config command supports
reading/writing hw mac id into i2c memory. Placing this code within
CONFIG_CMD_NET as this would only be needed when network interface is configured
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
While the u-boot code is running from the flash, it is essential that no access
is made to the bss segment. This is due to the fact that .rel.dyn and .bss areas
overlap and former contains information used in relocation. In SPEAr, this was
not taken into consideration. As a result, while the relocation wasn't complete,
dram_init populated an uninitialized global variable resulting in corruption of
.rel.dyn area, which resulted in u-boot crash.
This commit fixes this problem by removing code that accesses bss segment
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
There are two problems in the current timeout loop implementation:
1. In case initial test failing, there will always be a delay of 1 ms
2. The delay duration is not tunable
The new implementation addresses both these limitations.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
If the flash size was smaller than 1MB then flash_print_info()
was erroneously reporting 0 MB.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
THis patch introduces a new methodology for flash probing
in which flash_devices[] table, looked-up thru the dev_id, is
used to locate the flash geometry and information.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the smi erase code is very generic and works for any kind
of flash, there is no need to test for ST_M25Pxx_ID flash types
like m25p40 flashes).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
smi_read_sr fails sometimes because of TFF not getting set within assumed time.
This condition may arise because of, for example, smi memory being in a erase
mode.
This fix is to enable reading the status register until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI driver read status fails because the control register could not be
overwritten. Instead, the read status should be tried until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit does the following:
- Reports error if SNOR flash is not found on the board
- Changes smi_read_sr to return error using which a retry mechanism is
implemented for reading flash status
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Curently the code makes wrong assumption that the Transfer finished flag shall
be set within the stipulated time. However, there may occur a scenario in which
the TFF flag is not set. Return error in that case.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
