drivers/usb/gadget/composite.c requires that this is defined early.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Support for NAND storage devices to work with the DFU framework.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Previously we didn't support upload/download larger than available
memory. This is pretty bad when you have to update your root filesystem
for example.
This patch removes that limitation (and the crashes when you transfered
any file larger than 4MB) by making raw image writes be done in chunks
and making file maximum size be configurable.
The sequence number is a 16 bit counter; make sure we handle rollover
correctly. This fixes the wrong transfers for large (> 256MB) images.
Also utilize a variable to handle initialization, so that we don't rely
on just the counter sent by the host.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Increase size of DMA buffer from 4MiB to 8MiB. This is necessary due to
uImage size increase.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Now with kernel moving to all device tree, the default
boot command is changed to pass the device tree blob.
Also, adding the findfdt command to get the dt-blob
based on the board.
Thanks to Tom Rini <trini@ti.com> for suggesting this.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
For production systems it is better to use script images since
they are protected by checksums and carry valuable information
like name and timestamp. Also, you can't validate the content
passed to env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP5evm/uevm boards are used primarily for development,
we allow U-Boot to load env var from a text file in case that an
boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Inspired by commit: d70f54808d
(omap4: allow the use of a plain text env file instead boot scripts)
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sricharan R <r.sricharan@ti.com>
While booting with dt blob, if fdt_high is not set to
0xffffffff, the dt blob gets relocated to a high ram address,
which the kernel is not able to use without HIGHMEM.
So set it to 0xffffffff to avoid the issue.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
The function get_timer() should return time in ms and CONFIG_SYS_HZ
should be set to 1000 by default. Fix both of these items.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.
Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
Flush UART3 xmit on enable if TEMT is broken
On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
On TI AM335x devices, MUSB has bulk split/combine feature enabled
in the ConfigData register, but the current MUSB driver does not
support it yet. Therefore, disable the feature for now, until the
driver adds the support.
One usecase which is broken because of this feature is that Ether
gadget stops working in Fullspeed mode (by un-defining
CONFIG_USB_GADGET_DUALSPEED)
After desabled this feature, MUSB driver send packets in proper size
(no more than 64 bytes) in Fullspeed mode.
This has been validated with Ether gadget in Fullspeed mode on AM335x
EVM.
Signed-off-by: Bin Liu <b-liu@ti.com>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
CONFIG_SYS_FSL_USDHC_NUM is not used for wandboard.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The netargs variable was referencing the non-existing variable
console_mainline. Change that to console variable instead.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The mx25pdk board supports the i.MX25 DryIce RTC (imxdi), so enable it. This
allows to compile-test the imxdi driver in the mainline tree.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Introduce 'mx28evk_nand' target for saving environment variables into NAND.
The mx28evk board does not come with a NAND flash populated from the
factory. It comes with an empty slot (U23), which allows the insertion of a
48-pin TSOP flash device.
Tested with a K9LBG08U0D.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This commit is based on that patch from aaron.williams@caviumnetworks.com
with same commit title. pulled the same code changes into current u-boot tree.
http://patchwork.ozlabs.org/patch/140863/http://lists.denx.de/pipermail/u-boot/2011-April/089606.html
This patch corrects the addresses used when working with Spansion/AMD FLASH chips.
Addressing for 8 and 16 bits is almost identical except in the 16-bit case the
LSB of the address is always 0. The confusion arose because the addresses
in the datasheet for 16-bit mode are word addresses but this code assumed it was
byte addresses.
I have only been able to test this on our Octeon boards which use either an 8-bit
or 16-bit bus. I have not tested the case where there's an 8-bit part on a 16-bit
bus.
This patch also adds some delays as suggested by Spansion.
If a part can be both 8 and 16-bits, it forces it to work in 8-bit mode if an
8-bit bus is detected.
Apart from the pulled changes, fixed few minor code cleanups and tested
on 256M29EW, 512M29EW flashes.
Before this fix:
---------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0xFF, Device ID: 0xFF
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
After this fix:
--------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0x89, Device ID: 0x7E2301
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
This enables hash command.
Tested with command "hash sha256 0x40008000 0x2B 0x40009000".
Used mm and md to write a standard string to memory location
0x40008000 and ran the above command to verify the output.
Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Adding H/W acceleration support to hash which can be used
to test SHA 256 hash algorithm.
Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
* default bootmenu entries:
attached kernel, internal eMMC memory, external SD card,
u-boot boot order
* in CONFIG_PREBOOT try load bootmenu.scr from first partition
of internal eMMC memory (also known as MyDocs) which (should)
overwrite default bootmenu entries
* when keyboard slide is closed boot first menu entry
* when keyborad slide is open show bootmenu
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The "bootmenu" command uses U-Boot menu interfaces and provides
a simple mechanism for creating menus with several boot items.
When running this command the menu will be assembled as defined
by a set of environment variables which contain a title and
command key-value pairs. The "Up" and "Down" keys are used for
navigation through the items. Current active menu item is
highlighted and can be selected using the "Enter" key.
The command interprets and generates various ANSI escape
sequencies, so for proper menu rendering and item selection
the used terminal should support them.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[agust: various fixes and documentation updates]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Checking the default menu item and obtaining its data can
be useful in custom menu code. Export menu_default_choice()
function which serves this purpose.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Selecting menu items is currently done in menu_interactive_choice()
by reading the user input strings from standard input.
Extend menu_interactive_choice() to support user defined function
for selecting menu items. This function and its argument can be
specified when creating the menu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
"spl_imgsize" was set as decimal variable by "setexpr"
and this causes wrong image size written by "ext4write".
Preset this val with "0x" prefix allow to fix this issue.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is not called outside of env_callback.c so mark static, remove from
<env_callback.h>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
This patch is tested only on SMDK5250.
For Trats and universal_c210 board, it is only compile tested.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tested on my Dalmore E1611 board, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20/30).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Turn on SPI in dalmore config file
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add driver for tegra114 SPI controller. This controller is not
compatible with either the tegra20 or tegra30 controllers, so it
requires a new driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add "nvidia,tegra114-spi" to represent t114 SPI controller hardware.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add a common interface to fdt based SPI drivers. Each driver is
represented by a table entry in fdt_spi_drivers[]. If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Rename tegra SPI drivers to tegra20_flash and tegra20_slink in
preparation for commonization and addition of tegra114_spi.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Make bootcmd run findfdt so that we know what dtb file to load. Add a
loadfdt command to load this file in. Make mmcboot pass in ${fdtaddr}
and make the mmc section of bootcmd run loadfdt.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
The kernel is loaded from some form of ext[234] or FAT, depending on the
distribution used. We add a bootpart variable to the environment so
that we can load from the correct mmc partition as well. We leave
CONFIG_CMD_EXT2 for existing scripts that use ext2load.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Add support for loading splash image from NAND
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Hide the console macros since some reference global data which is
no longer present.
cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
- Make the brackets of the function calls more consistent
- Remove really unnecessary brackets
- Removes the extern from the function definitions
- Remove curly brackets from single line statements
- Remove lcd_setmem proto since it is already in common.h
- Cleanup comments, remove useless comments
- Remove NOT_USED_SO_FAR ifdef
- Cleanup coding style
cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: rebased the original patch]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
lcd_base is available as gd->fb_base as well, there is no need
to keep a seperate copy.
For completeness the ack of Bo Shen is for the atmel part.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fix cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
console_col, console_row, lcd_line_length, lcd_console_address had
to be declared in board / driver specific code, but were not actually
used there on many boards. Get rid of the global variables.
for completeness, the ack of Bo Shen is for the atmel part
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: rebased and fixed cm_t35 board]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Since the lcd code was compiled unconditionally for pxa also add
CONFIG_PXA_LCD to the boards using this framebuffer. Since
driver/video contains video and lcd drivers, add lcd to the name
to make clear it belongs to common/lcd.c.
cc: Anatolij Gustschin <agust@denx.de>
cc: Cliff Brake <cliff.brake@gmail.com>
cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Since the lcd code was compiled unconditionally in arch also
add CONFIG_MPC8XX_LCD to the boards using this driver.
cc: Anatolij Gustschin <agust@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
lcd_color_fg and lcd_color_bg had to be declared in board specific
code, but were not actually used there; in addition, we have getter /
setter functions for these, which were not used either.
Get rid of the global variables, and use the getter function where
needed (so far no setter calls are needed).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fixed cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Enable the SD controller driver for the Raspberry Pi. Enable a number
of useful MMC, partition, and filesystem-related commands. Set up the
environment to provide standard locations for loading a kernel, DTB,
etc. Provide a boot command that loads and executes boot.scr.uimg from
the SD card; this is written considering future extensibilty to USB
storage.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The firmware running on the bcm2835 SoC's VideoCore CPU manages the
display controller. Add a simple "LCD" driver that communicates with the
firmware using the property mailbox protocol. This configures the
display and frame-buffer to match whatever physical resolution the
firmware chosen when booting, which is typically the native resolution
of the attached display device, presumably unless otherwise specified
in config.txt on the boot media.
Enable this driver in the Raspberry Pi board configuration.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
There appears to be no implementation of flush_dcache_range() for
ARM1176, so explicitly disable dcache support to avoid references to
that function from the LCD core in the next patch. This was presumably
not noticed before simply because no drivers for the rpi_b were
attempting DMA.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Wandboard is a development board that has two variants: one version based
on mx6 dual lite and another one based on mx6 solo.
For more details about Wandboard, please refer to: http://www.wandboard.org/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When loading a Freescale 2.6.35 on a mx28evk the following issue is seen:
sgtl5000_hw_read: read reg error : Reg 0x00
Device with ID register 0 is not a SGTL5000
Disabling CONFIG_CMD_I2C makes the sgtl5000 probe to succeed.
Mainline kernel does not show this problem.
Until the real cause is not identified, disable 'CONFIG_CMD_I2C' for the
time being.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
No need to use multi-line style comments for single-line contents.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This command is useful for measuring SPI flash load times and the like.
Enable gettime as well to obtain absolute time tick values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable device tree control of SPI flash, and use this to implement
memory-mapped SPI flash, which is supported on Intel chips.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some SPI controllers (e.g. Intel ICH) have a limit on the number of SPI
bytes that can be written at a time. Add this as a parameter so that
clients of the SPI interface can respect this value.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is difficult to extend the SPI flash structure since
all devices allocate it themselves, and few of them zero all fields.
Add a new function spi_flash_alloc() which can be used by SPI devices
to perform this allocation, and thus ensure that all devices can
better cope with SPI structure changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is difficult to extend the SPI structure since all
drivers allocate it themselves, and few of them zero all fields. Add
a new function spi_alloc_slave() which can be used by SPI drivers
to perform this allocation, and thus ensure that all drivers can
better cope with SPI structure changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is common to have a "reg = <address size>" property in the FDT.
Add a function to handle this, similar to the existing
fdtdec_get_addr();
Signed-off-by: Simon Glass <sjg@chromium.org>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables new "ums" command on Trats board
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This patch adds the USB Mass Storage Gadget to u-boot
New command called "ums" is implemented to provide access
to on-device embedded persistent memory.
USB Mass Storage is supposed to work on top of the USB
Gadget framework
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marek.vasut@gmail.com>
We decided to used unsigned int here, rather than unsigned long. But
for the generic global_data it is still unsigned long. So change it
over.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards define CONFIG_LAST_STAGE_INIT and CONFIG_BOARD_EARLY_INIT_R
but these options are not available on ARM. Move them into the powerpc
common file instead.
This change affects: km_kirkwood_pci, mgcoge3un, kmnusa, kmcoge5un,
km_kirkwood and portl2.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file handles common pre-relocation init for boards which use
the generic framework.
It starts up the console, DRAM, performs relocation and then jumps
to post-relocation init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
These functions are only available for powerpc and are not declared in a
header file. We want to use the rest function in two places (board_f and
board_r), so declare the functions in watchdog.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
This library supports calling a list of functions one after the
other.
It is intended that we move to a more powerful initcall implementation
as proposed by Graeme Russ <graeme.russ@gmail.com>. For now, this allows
us to do the basics.
Signed-off-by: Simon Glass <sjg@chromium.org>
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
This file holds the board info structure. We need this to be generic
for the unified board series, so create a structure which contains
the basic fields required by the main architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable a common set of partition types, filesystems, and related
commands in tegra-common.h, so that they are available on all Tegra
boards. This allows boot.scr (loaded and executed by the default
built-in environment) on those boards to assume that certain features
are always available.
Do this in tegra-common.h, so that individual board files can undefine
the features if they really don't want any of them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Various code that is conditional upon HAVE_BLOCK_DEVICE is required by
code conditional upon CONFIG_CMD_PART. So, enable HAVE_BLOCK_DEVICE if
CONFIG_CMD_PART is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This set of ifdefs is used in a number of places. Move its definition
somewhere common so it doesn't have to be repeated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
All Tegra devices will need CONFIG_BOUNCE_BUFFER. Move it to
tegra-common.h to ensure it's always set.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested on my Cardhu-A04 tablet, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tegra30 SD/MMC controller differs enough from Tegra20 that it
needs its own entry in the compat_names/compat_id tables and in
the Tegra MMC driver.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested all 5 'buses', i2c probe enumerates device addresses on bus
0, 1 and 2.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
T114 has a slightly different I2C clock, with a new (extra) divisor
in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C
clock is 100KHz +/- 3Hz on my Saleae Logic analyzer.
Added a new entry in compat_names for T114 I2C since it differs
from the previous Tegra SoCs. A flag is set when T114 I2C HW is
found so new features like the extra clock divisor can be used.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tegra20 has a Cortex A9 r1p1, and Tegra30 has a Cortex A9 r2p9. As such,
some CPU errata exist, and must be worked around.
These must be worked around in the bootloader, since in general, the
kernel (especially a multi-platform kernel) needs to support being
launched in non-secure mode (normal world), and hence may not be able
to write to the CP15 register to enable these workarounds.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Many SPL linker scripts needlessly include linker lists (aka LGAs).
Remove them whenever possible; keep it only in the seven am335x_evm
variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot),
where there is actual content in output section .u_boot_list.
This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets
byte-identical.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Support to boot zImage
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Add bootz for at91rm9200, at91sam9263, at91sam9rl]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
support to boot device tree Linux kernel
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Add libftd for at91rm9200, at91sam9263, at91sam9rl]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch adds the configuration file for Snow Board and
defines the same in boards.cfg.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This enables the dtt command to read the current SOC
temperature with the help of TMU
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enables TMU driver support for exynos5250
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fdt entry for Exynos TMU driver specific pre-defined values used for
calibration of current temperature and defining threshold values.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding Exynos Thermal Management Unit driver to monitor SOC
temperature and take actions corresponding to states of TMU.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
The "mtest" command is of little practical use (if any), and
experience has shown that a large number of board configurations
define useless or even dangerous start and end addresses. If not even
the board maintainers are able to figure out which memory range can be
reliably tested, how can we expect such from the end users? As this
problem comes up repeatedly, we rather do not enable this command by
default, so only people who know what they are doing will be
confronted with it.
As this changes the user interface, we allow for a grace period
before this change takes effect. For now, we make "mtest"
configurable through the CONFIG_CMD_MEMTEST variable, which is defined
in include/config_cmd_default.h; we also add an entry to
doc/feature-removal-schedule.txt which announces the removal of this
default setting in two releases from now, i. e. with v2013.07.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Define CONFIG_SPLASHIMAGE_GUARD to prevent splashimage from being
set to a value that will cause U-Boot to hang while displaying a
splash screen.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
On some architectures certain values of splashimage will lead to
a data abort exception.
Document the problem, and implement a callback for splashimage to
reject such values.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: R Sricharan <r.sricharan@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Signed-off-by: Tom Rini <trini@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: R Sricharan <r.sricharan@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
This patch will allow use SPL to boot an u-boot from the OneNAND.
Tested with IGEPv2 board with a OneNAND from Numonyx
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
[trini: Add <spl.h> hunk to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Only define enabled clocks in the config file and enable
the clocks in common code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Remove CSx configurations from board code and only define
required CSx macros in the board config file to configure
chip select windows and parameters.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
This patch adds a custom U-Boot command "wdogtoggle" which enables the
external hardware watchdog toggling via an GPIO pin on the a4m2k
board. After issuing this commands, the watchdog will be serviced
by U-Boot so that the user can use all U-Boot commands from the
prompt.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the a4m2k MPC5200B board port. Its a derivate of
the a3m071 board with only minor changes.
Additionally this patch includes some clean-up changes:
- Remove I2C support from a3m071 as its unused
- Fix/enhance default env variables
- Fix some comments
- Add newly introduced CONFIG_SPL_TARGET to automatically build
"u-boot-img.bin"
- Fix dtb patching in READ desciption for SPL Linux booting:
"fdt chosen" needs to get called to patch/create the chosen node.
- Add missing call to spl_board_init():
Define CONFIG_SPL_BOARD_INIT so that spl_board_init() will get
called in the SPL version.
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for dvi displays with user selectable dvi presets.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Currently there is no logical place to put the code that prepares the
splash image data. The splash image data should be ready in memory
before bmp_display() is called, and after the environment is ready
(since lcd.c looks for the splash image in an address specified by
the environment variable "splashimage").
Our window of opportunity in board_init_r() is therefore: between
env_relocate() and bmp_display(), and from the available options
only the lcd related functions in drv_lcd_init() seem appropriate
for such lcd oriented code.
Add the option to prepare the splash image data in lcd_logo() right
before it is sent to be displayed.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
We add USB (RNDIS gadget) SPL support as a separate target. We need to
pull out YMODEM support in order to be a small enough target binary.
Signed-off-by: Tom Rini <trini@ti.com>
Because of our support for network-based SPL, we don't discard all of
the environment related functions. We however never make use of the
default CONFIG_EXTRA_ENV_SETTINGS items and as this variable grows, it
brings us closer to (or with some toolchains, over) our SPL size limit.
Never set this in the case of SPL.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables MAX98095 codec required for Snow
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add required compatible information for MAX98095 codec
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patchs adds support for MAX98095 codec in
sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that U-Boot has common CONFIG_ options to work around some ARM CPU
errata, enable the relevant options on MX6, and remove the custom
lowlevel_init.S, since it's just duplicated code now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
This adds support to the LAN9512 chip included in the board and extend
the environment to easy netboot use.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Rework ehci-mxs so it supports both ports on MX28. It was necessary
to wrap the per-port configuration into struct ehci_mxs_port and pull
out the clock configuration function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The CONFIG_MXS_SPI_DMA_ENABLE is no longer relevant as the SPI DMA
has proven to work correctly. Remove this configuration option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
UBI can mount volumes by name or number The current code forces you
to name the volume by prepending every name with "ubi:".
>From fs/ubifs/super.c
* There are several ways to specify UBI volumes when mounting UBIFS:
* o ubiX_Y - UBI device number X, volume Y;
* o ubiY - UBI device number 0, volume Y;
* o ubiX:NAME - mount UBI device X, volume with name NAME;
* o ubi:NAME - mount UBI device 0, volume with name NAME.
Now any name passed in any of the above forms are allowed.
Also update the configs that referenced ubifsmount.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The 'sb' command allows loading files from the host, and listing
directories.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The new 'sb' command is intended to deal with sandbox-specific features
that have no parallel in other archs. This commit adds two sub-commands
to list a directory and read a file from the host filesystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This implementation uses opendir()/readdir() to access the directory
information and then puts it in a linked list for the caller's use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
It doesn't make a lot of sense to have these methods in fs.c. They are
filesystem-specific, not generic code. Add each to the relevant
filesystem and remove the associated #ifdefs in fs.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Board and config header files for bf609-ezkit support.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
CONFIG_SPL_OS_BOOT_KEY is used only in board files. It is
not required to have a general CONFIG_ option. Rename it and
define it in board directory.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Rather than use strcasecmp() in the hash algorithm search, require the
caller to do this first. Most of U-Boot can use lower case anyway, and
the hash command can convert to lower case before calling hash_command().
This saves needing strcasecmp() for boards that use hashing but not
the hash command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the hash command and sha1/256 hashing for sandbox. Also use a
better address for memory testing (since the existing one is set up
for linux host memory space).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the CRC32 algorithm to the list of available hashes, and make
the crc32 command use hash_command(). Add a new crc32_wd_buf() to
make this possible, which puts its result in a buffer rather than
returning it as a 32-bit value.
Note: For some boards the hash command is not enabled, neither
are sha1, sha256 or the verify option. In this case the full
hash implementation adds about 500 bytes of overhead. So as a
special case, we use #ifdef to select very simple bahaviour in
that case. The justification for this is that it is currently
a very common case (virtually all boards enable crc32 but only
some enable more advanced features).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some hashing commands permit saving the hash in an environment variable,
and verifying a hash from there. But the crc32 command does not support
this. In order to permit crc32 to use the generic hashing infrastructure,
add a flag to select which behaviour to use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox doesn't actually provide U-Boot access to the machine's physical
memory. Instead it provides a RAM buffer of configurable size, and all
memory accesses are within that buffer. Sandbox memory starts at 0 and
is CONFIG_DRAM_SIZE bytes in size. Allowing access outside this buffer
might produce unpredictable results in the event of an error, and would
expose the host machine's memory architecture to the sandbox U-Boot.
Most U-Boot functions assume that they can just access memory at given
address. For sandbox this is not true.
Add a map_sysmem() call which converts a U-Boot address to a system
address. In most cases this is a NOP, but for sandbox it returns a
pointer to that memory inside the RAM buffer.
To get a U-Boot feature to work correctly within sandbox, you should call
map_sysmem() to get a pointer to the address, and then use that address for
any U-Boot memory accesses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implements the tstc() interface for the serial driver. Multiplexing
the console between the serial port and a keyboard uses a polling
method of checking if characters are available; this means that the
serial console must be non-blocking when attempting to read
characters.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The buffer cannot be changed by this function, so change the buffer
pointer to a const. This allows callers with const pointer to use the
function without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This pulls the three following ZYNQ commits into ARM master:
7dca54f8: xilinx: zynq: Enable DCC and create new zynq_dcc board
59c651f4: arm: zynq: Add SLCR support with system reset
00ed3458: arm: zynq: Add lowlevel initialization to C
This patch adds required pmic voltage settings for SMDK5250.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add 'ustrtoull' function to convert size from string (ex: 1GiB)
to unsigned long long type
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
On architectures where manual relocation
is needed, the 'malloc_bin_reloc' function
must be called after 'mem_malloc_init'.
Make the 'malloc_bin_reloc' function static
and call it directly from 'mem_malloc_init'
instead of calling that from board_init_{r,f}
functions of the affected architectures.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andreas Bießmann <andreas.devel@gmail.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add at91sam9g20_2mmc nand boot support. on this board, there is no
dataflash, so disable it
change one commet for at91sam9g20ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This target will move the environment into SPI flash and documents
the expected layout. We correct the SPL define for where U-Boot is
and remove an unused define.
Signed-off-by: Tom Rini <trini@ti.com>
* Added variables to support SPI booting
* Note that the first 512KiB are reserved for 4 copies of SPL.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added support to the default environment variables for NAND
boot.
* Add nandboot to the default bootcmd.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Rather than load the FPGA file from the FAT partition, look
at entry in system EEPROM to decide which file to retrieve directly
from the EXT3 partition.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Also, change bootdelay to 0 but allow pressing 'S' to stop at U-Boot prompt.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard Gray <howard.gray@matrix-vision.de>
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
