PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII to TI phy dp838367
Enable the SGMII and PCS settings in phy
control, CFG2 and BIST registers
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass appropriate interface type to phy_connect
instead of zero.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.
Tested on the Marvell Armada 375 eval board db-88f6720.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
This enables this driver for the Marvell Armada 375 SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviwer-by: Jagan Teki <jteki@openedev.com>
The RTL8211B_driver structure in drivers/net/phy/realtek.c contains a
wrong PHY ID (0x1cc910 instead of 0x1cc912) in the uid field.
The lowest four bits of the PHY ID encode the chip revision (B+C/D/E/F)
of the RTL8211 and the code originally applied a mask of 0xfffff0 to
the PHY ID, so that matching the PHY ID to the appropriate driver code
was only done on the chip type (RTL8211), but not on a specific
revision.
After introduction of support for the RTL8211E, which needed another
startup function than the older chip revisions, commit
4220504767 changed the mask to 0xffffff
to make the chip revision relevant for the match, but didn't provide
the now-relevant lower bits of the uid field for the RTL8211B/C.
Fix this by setting the full PHY ID in the RTL8211B_driver uid field.
Fixes: 4220504767 ("net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected")
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a block device cache to speed up repeated reads of block devices by
various filesystems.
This small amount of cache can dramatically speed up filesystem
operations by skipping repeated reads of common areas of a block
device (typically directory structures).
This has shown to have some benefit on FAT filesystem operations of
loading a kernel and RAM disk, but more dramatic benefits on ext4
filesystems when the kernel and/or RAM disk are spread across
multiple extent header structures as described in commit fc0fc50.
The cache is implemented through a minimal list (block_cache) maintained
in most-recently-used order and count of the current number of entries
(cache_count). It uses a maximum block count setting to prevent copies
of large block reads and an upper bound on the number of cached areas.
The maximum number of entries in the cache defaults to 32 and the maximum
number of blocks per cache entry has a default of 2, which has shown to
produce the best results on testing of ext4 and FAT filesystems.
The 'blkcache' command (enabled through CONFIG_CMD_BLOCK_CACHE) allows
changing these values and can be used to tune for a particular filesystem
layout.
Signed-off-by: Eric Nelson <eric@nelint.com>
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This PMIC is connected on SPMI bus so needs SPMI support enabled.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Support SPMI arbiter on Qualcomm Snapdragon devices.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Use definitions from ehci.h instead.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Debug printf used '%u' to print size_t variable.
This caused warnings on 64-bit machines.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.
This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.
It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.
This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
The following options can be now enabled via defconfig:
- CONFIG_USB_ULPI
- CONFIG_USB_ULPI_VIEWPORT
- CONFIG_USB_ULPI_VIEWPORT_OMAP
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Some host controllers need addidional initialization after ehci_reset()
In non-dm implementation it is possible to use CONFIG_EHCI_HCD_INIT_AFTER_RESET.
This patch adds similar option to ehci drivers using dm.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add support for gpio controllers on Qualcomm Snapdragon devices.
This devices are usually called Top Level Mode Multiplexing in
Qualcomm documentation.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
smsc95xx_read_reg() should calculate sizeof(*data) not sizeof(data) since
data is a pointer, and the value pointed at is being transferred over USB,
not the value of the pointer. This fixes operation of the driver in 64-bit
builds, such as the Raspberry Pi 3.
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some boards need to expose device specific variable through fastboot
(to adpat the flashing script depending on hardware revision for
example).
Provide a way to expose custom fastboot variables. Note that all
variables meant to be exposed through fastboot should be be prefixed
with 'fastboot.', the variable should not exceed 32 bytes (including
the prefix and the trailing '\0') and the variable content should
fit in the response buffer (60 bytes excluding the 'OKAY' prefix and
the trailing '\0').
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[Boris Brezillon: add a commit message]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Steve Rae <srae@broadcom.com>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit prepares the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones. Having flags would be better than
adding new members every time a new SoC-specific capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.
Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS drive is supported on AXP221 and later PMICs. Rework the macros
so we can support this on later PMICs without too much work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Like the Allwinner A33 SoC, the A83T is missing the config register
from the musb USB DRD hardware block. Use a known working value for
it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.
This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.
There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.
CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit solves CAAM coherency issue on ls2080. When caches are
enabled and CAAM's DMA's AXI transcations are not made cacheable,
Core reads/writes data from/to caches and CAAM does from main memory.
This forces data flushes to synchronize various data structures. But
even if any data in proximity of these structures is read by core,
these structures again are fetched in caches.
To avoid this problem, either all the data that CAAM accesses can be
made cache line aligned or CAAM transcations can be made cacheable.
So, this commit makes CAAM transcations as write back with write and
read allocate.
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When MMU is disabled, 64-bit write must be aligned at 64-bit
boundary. Becaue the memory location is not guaranteed to be 64-bit
aligned, the 64-bit write needs to be split into two 32-bit writes
to avoid the alignment exception.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NULL pointer should be checked before any dereference. This patch
move memest after the NULL pointer check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Free dflt_dpio pointer after its usage during error handling
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Otherwise flash remains in read status mode and it's not possible
to access data on flash.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When DEBUG_RTL8169 is on, a build error occurs in function
'rtl_init': error: 'dev' undeclared. Fix this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
send_cmd response is valid only when no error happened. If an error
occured, let mmc_send_cmd() print the return value to aid debugging.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes:
drivers/mmc/bcm2835_sdhci.c: In function ‘bcm2835_sdhci_init’:
drivers/mmc/bcm2835_sdhci.c:181:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The bcm2835 frame buffer is in RAM, so we can easily map it as cached and gain
all the glorious performance boost that brings with it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for programming of the StratixV FPGAs. Programming
is done in this case (board theadorable) via SPI. The board may provide
board specific code for bitstream programming.
This StratixV support will be used by the theadorable board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a DM GPIO driver for the Marvell MVEBU SoCs. There are
other non-DM drivers that might be used on these platforms. But this
patch creates a new DM driver. Which will be used by all Armada XP/38x
boards. Other MVEBU SoC (Kirkwood / Orion) may follow once they
support DM as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Armada 38x has a maximum of two cores. Probably copy/paste
bug from Armada XP.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The 2nd usb controller on sun4i/sun7i has its base address 0x8000
bytes from the 1st one, rather then 0x1000. Also the ahb clk gates
are interleaved with the ohci clk-gates introducing a hole between
the clks for usb1 and usb2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The kernel has different compatible strings for the pio block
because the pin-muxing is different on all the different SoCs,
but sunxi_gpio.c only support the basic gpio functionality, which
is identical everywhere. Add the missing compatible strings for
various SoC models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The behavior before this patch would attempt to configure the mux
setting for pins 0 to 27 on PORTD to all be setting 3 for LVDS. The
LVDS interface actually only uses pins 18 to 27 and not pins 0 to 27
as in the parallel LCD interface. This patch restricts the
configuration to only the relevant pins 18 to 27 on PORTD.
This was tested on a sun8i A33 tablet with an LVDS screen. MMC1 has
the capability to use pins 2 to 7 on PORTD and the mux on those pins
was being inadvertently set to setting 3 for MMC functionality which
this patch corrects.
Signed-off-by: Lawrence Yu <lyu@micile.com>
[hdegoede@redhat.com: Only apply this change to A23 / A33]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For ARM32 architecture, CONFIG_DEBUG_LL is available for early
low-level debugging (and actually UniPhier 32bit SoCs use it), but
ARM64 architecture does not support it. Instead, CONFIG_DEBUG_UART
is available as an architecture-independent debug facility.
This commit supports it on all the UniPhier SoCs (including the new
ARMv8 SoCs), which is very useful for new SoC bringups.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long. It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family. Also, rename files for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The 64-bit compiler (ex. aarch64) emits "warning: cast from pointer
to integer of different size".
Make it work with 64bit DMA address while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt. Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Return value of get_mc_boot_status() in case of failure is not necessary
to be -1.
So update the error condition check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Yao Yuan <yao.yuan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch integrate DPAA2 ethernet driver existing PHY framework.
Call phy_connect and phy_config as per available DPMAC id defined
in SerDes Protcol.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of address parity for DDR4 UDIMM or discrete memory.
It requires to configurate corresponding MR5[2:0] and
TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig,
e.g. hwconfig=fsl_ddr:parity=on.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
msi-map properties are used to tell an OS how PCI requester IDs are
mapped to ARM SMMU stream IDs.
for all PCI devices discovered in a system:
-allocate a LUT (look-up-table) entry in that PCI controller
-allocate a stream ID for the device
-program and enable a LUT entry (maps PCI requester id to stream ID)
-set the msi-map property on the controller reflecting the
LUT mapping
basic bus scanning loop/logic was taken from drivers/pci/pci.c
pci_hose_scan_bus().
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove stream ID partitioning support that has been made
obsolete by upstream device tree bindings that specify how
representing how PCI requester IDs are mapped to MSI specifiers
and SMMU stream IDs.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Structures are defined for PDB (Protocol Data Blcks) for various
operations. These structure will be used to add PDB data while
creating the PDB descriptors.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
CC: Ulises Cardenas <raul.casas@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When CAAM runs a descriptor and an error occurs, a non-zero
value is set in Output Status Register. The if condition should
check the status for a non-zero value.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add test into xhci_submit_control_message for usb requesttype in USB
vendor request being of standardized type. This fixes detection of
certain USB fixes, for example Ethernet, USB 3.0 port. Non standardized
requesttype in USB vendor request will be ignored.
Signed-off-by: Ted Chen <tedchen@realtek.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Driver model is used for host device block devices now, so we don't need the
old code. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
When 'usb start' is used, block devices are created for any USB flash sticks
and disks, etc. When 'usb stop' is used, these block devices are currently
not removed.
We don't want old block devices hanging around since they can still be
visible to U-Boot. Therefore, when USB is shut down, remove and unbind all
the block devices created by the USB subsystem.
Possibly we should unbind all devices which don't cause problems by being
unbound. Most likely we can remove everything except USB controllers, hubs
and emulators. We can consider that later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moved the new field to the end of the struct to avoid problems:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a video driver for Intel's broadwell integrated graphics controller.
This uses a binary blob for most init, with the driver just performing a few
basic tasks.
This driver supports VESA as the mode-setting mechanism. Since most boards
don't support driver model yet with VESA, a special case is added to the
Kconfig for broadwell. Eventually all boards will use driver model and this
can be removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a GPIO driver for the GPIO peripheral found on broadwell devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
We don't need this anymore - we can use device tree and the new pinconfig
driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than setting up the pin configuration in the GPIO driver, use the
new pinctrl driver to do it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present on x86 machines with use cache-as-RAM, the memory goes away just
before board_init_r() is called. This means that serial drivers are
no-longer unavailable, until initr_dm() it called, etc.
Any attempt to use printf() within this period will cause a hang.
To fix this, mark the serial devices as 'unavailable' when it is no-longer
available. Bring it back when serial_initialize() is called. This means that
the debug UART will be used instead for this period.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add one more step into the init sequence. This fixes the keyboard on samus,
which otherwise does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If the device cannot be probed, syscon_get_by_driver_data() will still
return a useful value in its devp parameter. Ensure that it returns NULL
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel GPIO driver can set up the GPIO pin mapping when the first GPIO
is probed. However, it assumes that the first GPIO to be probed is in the
first GPIO bank. If this is not the case then the init will write to the
wrong registers.
Fix this. Also add a note that this code is deprecated. We should move to
using device tree instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Two comments are missing a parameter and there is an extra blank line. Also
two of the region access macros are misnamed. Correct these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is common to read a config register value, clear and set some bits, then
write back the updated value. Add functions to do this in one step, for
convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some functions do not change the struct gpio_desc parameter. Update these to
use const so this is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We can use GPIOs as binary digits for reading 'strapping' values. Each GPIO
is assigned a single bit and can be set high or low on the circuit board. We
already have a legacy function for reading these values. Add one that
supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present simple-panel requires regulator support and will not build
without it. But some panels do not have a power supply, or at least not one
that can be controlled. Update the implementation to cope with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Move asm/arch-coreboot/tables.h to asm/coreboot_tables.h so that
coreboot table definitions can be used by other x86 builds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When enable dcache on HiKey, we're running into MMC command timeouts
because our retry loop is now faster than the eMMC (or an external SD
card) can answer.
Increase the retry count to the same as the timeout value for status
reports.
The real fix is obviously to not base this whole thing on a cycle counter
but on real wall time, but that would be slightly more intrusive.
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for detecting a few inputs exported by the TWL6030.
Currently-supported inputs are the power button, USB and charger presence.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The TWL6030 power driver is only built when CONFIG_TWL6030_POWER is selected,
thus there is no reason to wrap the code with ifdef.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for the OMAP4 MUSB USB controller, with a matching Linux
compat definition, TWL6030 USB device setup and USBOTGHS register setup.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When booting from USB, the bootrom sets the VUSB_IN_PMID bit of the MISC2
register of the TWL6030. However, U-Boot sets the VUSB_IN_VSYS bit to enable
VBUS input. As both bits are contradictory, enabling both disables the input,
according to the TWL6030 TRM.
Thus, we need to clear the VUSB_IN_PMID bit in case of an USB boot (which could
just as well be a memory boot after USB timed out).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Boards using the TWL6030 regulator may not all use the LDOs the same way.
Some might also not use MMC1 at all, so VMMC would't have to be enabled.
This delegates TWL6030 MMC power initializations to board-specific functions,
that may still call twl6030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC and VAUX1, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This enables the VAUX1 supply, used for eMMC power in standard configurations.
Its voltage is determined by the value of the BOOT2 pin of the TWL6030.
Note that the TWL6030 might already have enabled this regulator at startup
(depending on the value of the BOOT3 pin of the TWL6030), according to the
TWL6030 datasheet.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This makes the twl6030 mmc and usb-related power registers and values
definitions more explicit and clear and adds prefixes to them.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Global definition of priv seems no-sense to use it
for non-dm case and pass the pointer to functions
which are common to both dm and non-dm.
So, fix this by removing omap3_spi_slave from non-dm
and make visible to omap3_spi_priv for both dm and non-dm.
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
OMAP timer driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Many TI System on Chip (SoC) solutions do have a dedicated
microcontroller for doing power management functionality. These include
the AM335x, AM437x, Keystone K2G SoCs. The functionality provided by
these microcontrollers and the communication mechanisms vary very
widely. However, we are able to consolidate some basic functionality to
be generic enough starting with K2G SoC family. Introduce a basic remote
proc driver to support these microcontrollers. In fact, on SoCs starting
with K2G, basic power management functions are primarily accessible for
the High Level Operating Systems(HLOS) via these microcontroller solutions.
Hence, having these started at a bootloader level is pretty much
mandatory.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Multiplication, as "clk->parent->rate * 16" may overflow. So use
do_div to avoid such issue.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Sandor Yu <sandor.yu@nxp.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
As the handling for carriage return and line feed is done in the common
DM driver serial-uclass.c, such handling in some serial DM drivers is
duplicated and need to be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In general, a carriage return needs to execute before a line feed.
The patch is to change some serial drivers based on this rule, such
as serial_mxc.c, serial_pxa.c, serial_s3c24x0.c and usbtty.c.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In general, a carriage return needs to execute before a line feed. The
patch is to change serial DM driver serial-uclass.c based on this rule.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the host driver to support driver model for block devices. A future
commit will remove the old code, but for now it is useful to be able to use
it both with and without CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Make a few minor changes to make it easier to add driver-model support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add a uclass for block devices. These provide block-oriented data access,
supporting reading, writing and erasing of whole blocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Each region is displayed in almost the same way. Break out this common code
into its own function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Simple MFD devices can bind children without special bus configuration.
Like Linux, let's handle "simple-mfd" in the same way as "simple-bus".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
A common pattern is to call uclass_first_device() and then check if it
actually returns a device. Add a new function which does this, returning
an error if there are no devices in that uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
LVDS have a different display out mode, add code to get right flag.
The vop_ip decide display device and the remote_vop_id decide which
vop was being used. So we should use the remote_vop_id to set DCLK_VOP.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some Rockchip SoCs support LVDS output. Add a display driver for this so
that these displays can be used on supported boards.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
The current display class only allow to get timing from edid.
So add a operation to get timing directly from driver.
In driver, I will use fdtdec_decode_display_timing to get timing.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
After this conversion the driver will able to support both dm and non-dm
and code is more extensible like we can remove the non-dm part simply
without touching anycode if all the boards which are using this driver
become dm driven.
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Tested-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Set priv->wordlen, Add Kconfig entry and file credit for dm conversion]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Attach static on local defined functions.
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Header file have macro's and register definition and some unneeded
function proto types which becomes tunned further in future patches
and entire driver code resides in one file for more readability.
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Fixes on code styles, Remove omap3_spi_txrx|write|read in header]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it
into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
[ ported from Linux commit bac7f4c1bf5e7c6ccd5bb71edc015b26c77f7460 ]
Fixes: 5dc626f836 ("pinctrl: uniphier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
This reverts commit d9a3bec682.
While this is a correct change to do long term it unfortunately breaks a
number of platforms that are using pdata and not named struct members so
they are getting all of their data after 'base' incorrect.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This GPIO controller device is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.
To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the following warning on aarch64 introduced by using p2v/v2p
functions in the code:
In file included from ./arch/arm/include/asm/byteorder.h:29:0,
from include/compiler.h:125,
from include/image.h:19,
from include/common.h:88,
from drivers/usb/host/ehci-hcd.c:10:
drivers/usb/host/ehci-hcd.c: In function ‘ehci_td_buffer’:
drivers/usb/host/ehci-hcd.c:250:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
^
include/linux/byteorder/little_endian.h:34:51: note: in definition of macro ‘__cpu_to_le32’
#define __cpu_to_le32(x) ((__force __le32)(__u32)(x))
^
drivers/usb/host/ehci-hcd.c:250:24: note: in expansion of macro ‘cpu_to_hc32’
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Fix the following compiler warnings when DEBUG is on.
warning: 'bar_res' may be used uninitialized in this function.
drivers/pci/pci_auto.c:101:21:
if (!enum_only && pciauto_region_allocate(bar_res, bar_size,
^
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1e90d9fd (sf: Move read_id code to sf_ops)
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a little more debugging to help when things go wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
In some cases the timer must be accessible before driver model is active.
Examples include when using CONFIG_TRACE to trace U-Boot's execution before
driver model is set up. Enable this option to use an early timer. These
functions must be supported by your timer driver: timer_early_get_count()
and timer_early_get_rate().
Signed-off-by: Simon Glass <sjg@chromium.org>
A few of the functions in the timer uclass are not marked with 'notrace'. Fix
this so that tracing can be used with CONFIG_TRACE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enabling this driver requires some DT changes.
Adding DCC to root or main bus:
dcc: dcc {
compatible = "arm,dcc";
u-boot,dm-pre-reloc;
};
Extend alias list to link DCC:
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
Change stdout-path to point to dcc port.
stdout-path = "serial2:115200n8";
Also add support for debug uart to help with early debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the following functions:
tps65218_reg_read() for accessing redisters
tps65218_toggle_fseal() for toggling the fseal bit
tps65218_lock_fsea() for locking the fseal bit to 1
Add the following defines:
All status register bits
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Building pci_rom.c with my toolchain complains about may be used uninitialized
rom varaible:
---8<---
+drivers/pci/pci_rom.c:269:25: note: 'rom' was declared here
w+drivers/pci/pci_rom.c: In function 'dm_pci_run_vga_bios':
w+drivers/pci/pci_rom.c:154:14: warning: 'rom' may be used uninitialized in this function [-Wmaybe-uninitialized]
--->8---
Fix this as done in 55616b86c7 the ram variable.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch adds support for stm32f7 family usart peripheral.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Base addresses for GPIOs could be different for different socs, this
patch moves the base addresses from driver to the soc specific location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Fix the formatting in error messages, and demote one error message
to a warning, as it is only informational.
Signed-off-by: Steve Rae <srae@broadcom.com>
The alignment and size were swapped, leading to malloc heap corruption.
On my system, this sometimes caused U-Boot to crash during or after
certain USB Ethernet operations.
Fixes: c8c2797c38 ("dm: usb: eth: Support driver model with USB Ethernet")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reported-by: Alex Gdalevich <agdalevich@axion-biosystems.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Heiko Schocher <hs@denx.de>
Add explicit cpu_to_be32()/be32_to_cpu() conversion to BE EHCI I/O
accessors to align them with their LE counterpart. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
If the USB EHCI is configured for little endian MMIO, make sure to
clear the USBMODE_BE flag from the USBMODE register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Certain processor architectures, like MIPS, require that the USB
structures and transfer buffers are passed with their PA to the
USB controller. If VA is passed, the USB will not work. Add the
necessary virt_to_phys() calls into the USB EHCI code to make it
work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Some architectures, like MIPS, require remapping of the registers.
Add the map_physmem() call to handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
there are some code in qe.c not used for micro QE,
use "#ifdef CONFIG_QE" to mask them.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use fdt32_to_cpu() to convert the data correctly for both endianness
platforms.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The output ring needs to be invalidated before enqueuing the job to SEC.
While allocation of space to output ring, it should be taken care that the
size is cacheline size aligned inorder to prevent invalidating valid data.
The patch also correct the method of aligning end of structs while flushing caches
Since start = align(start_of_struct), it is incorrect to assign
end = align(start + struct_size). It should instead be,
end = align(start_of_struct + struct_size).
Signed-off-by: Saksham Jain <saksham@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In some case wordlen may not be set. Use SPI_DEFAULT_WORDLEN as default.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
adopt ti-edma3 driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add TI_EDMA3 entry on Kconfig with help description.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Implement a DMA uclass so that the devices like ethernet, spi,
mmc etc can offload the data transfers from/to the device and
memory.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add basic framebuffer driver for the S3C24xx family of CPUs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
V2: Keep the Makefile sorted.
Acked-by: Anatolij Gustschin <agust@denx.de>
The problem with current implementation is that SPDDONE bit is 1
but link bit is zero. That's why phydev->link is setup to 0
which ending up in driver failure that link is not up.
Log:
Zynq> dhcp
ethernet@e000b000 Waiting for PHY auto negotiation to complete.......
done
ethernet@e000b000: No link.
There is at least 1ms delay between spddone bit and link up.
Use genphy_read_status() instead of realtek implemenation which is
working with page 11. Linux driver is also using generic implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync logic with Linux kernel where TX empty flag is checked before char
is sent.
This logic is fixing problem with console on zynqmp platform.
For example:
DRAM: 2 GiB
Enabling Caches...
EL Level: �� sdhci@ff170000: 0
Using default environment
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
When the resolution is not supported we should free the memory we don't plan
to use.
Reported-by: Coverity (CID: 135127)
Signed-off-by: Simon Glass <sjg@chromium.org>
Introudce i.MX7 pinctrl driver support.
For now only i.MX7D supported.
There are two iomux controllers in i.MX7D, iomuxc and iomuxc_lpsr.
To iomuxc_lpsr, ZERO_OFFSET_VALID is set, means offset of mux_reg
and conf_reg can begin at 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
>;
};
[.....]
};
there is no property named function or groups. So pinctrl_generic_set_state
can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
"
set_state_simple op missing
imx_pinctrl_set_state: i2c1grp
mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x14c val 0x10
select_input: offset 0x5d8 val 0x1
write config: offset 0x3bc val 0x7f
mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x148 val 0x10
select_input: offset 0x5d4 val 0x1
write config: offset 0x3b8 val 0x7f
"
this means imx6 pinctrl driver works as expected.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactored data structure for CAAM's job ring and Secure Memory
to support i.MX7.
The new memory map use macros to resolve SM's offset by version.
This will solve the versioning issue caused by the new version of
secure memory of i.MX7
Signed-off-by: Ulises Cardenas <raul.casas@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.
This adds a simple driver to enable serial port and handle GPIO.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable/disable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new UTMI PLL clock handle functions,
use these function to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit 12
being cleared (A/N enable). This leads to autonegotiation link problems,
at least on the Marvell Armada ClearFog board. I suspect that other
boards using this driver will be affected as well.
At the of m88e1111s_config(), phy_reset() is called. This is not needed
for the PHY to load the changed configuration, as phy_reset() is called
a few lines before already. So lets call genphy_restart_aneg() here
instead to start the AN correctly.
Tested on clearfog.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of coding the soft PHY reset function multiple times in marvell.c,
lets call the common phy_reset() function from phy.c.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the driver-model PWM driver in preference to the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Join the two functions which decode the device tree and put them in the
ofdata_to_platdata() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no need to have these in a separate file as they are not
referenced from anywhere else.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We can move the static variables into the driver-private data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We have a structure for the display panel and another for the controller.
There is some overlap between them. Merge them to simplify the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We can check this in Kconfig now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present we have code in arch/arm and code in drivers/video. Move it all
into drivers/video since it is a display driver and our current approach is
to put all driver code in drivers/.
Make a few functions static now that they are not used outside the file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There isn't a lot of benefit of have two separate files. With driver model
the code needs to be in the same driver, so it's better to have it in the
same file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This PWM supports four channels. The driver always uses the 32KHz clock,
and adjusts the duty cycle accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The tegra GPIO controller has two ways of reading the value of a GPIO. It
can supply the 'input' value (which is the value read from the pin) and the
'output' value (which is the value being driven from the pin. With a GPIO
set to output mode, the 'input' value is always low which is not very
useful.
This has the unfortunate result that setting a GPIO high still leaves it
showing as low in the 'gpio status' command.
Adjust the driver to check which direction the GPIO is set to, then read
the value from the appropriate register: 'input' for input GPIOs, 'output'
for output GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This helps keep the display consistent. puts() is used when printing the
prompt, so is a useful way to make sure the current display contents is
visible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We need to add the base tables before adding the function tables. Fix the
init order so the keyboard scans keys correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
