SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Include "mx6_common.h" so that some ARM errata are applied and also the
vddsoc regulator can be changed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
The zImage works for FSL Linux's kernel fork versions 3.0.35, 3.10.9,
and 3.10.17; this also works fine for mainline kernels.
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
A new 'update_emmc_firmware' target is added to allow for easy U-Boot
update in the eMMC as it has secury boot partition and this needs
specific handling on how to program the specific partition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This patch fixes allow for the DeviceTree and initrd relocation fixing
the boot of FSL 3.10.9-1.0.0-alpha kernel.
This changes following boards:
- mx6sabreauto
- mx6sabresd
- wandboard
- udoo
- nitrogen6x
- cgtqmx6eval
The reasoning, as explained by Hui Liu, is:
,----
| The FDT blob will be placed at DDR physical addr: 0x11000000. When Linux kernel
| Boot up, it will decompress the compressed kernel image and place the decompressed
| kernel image at the low end of the DDR memory and start running from it. If the
| decompressed kernel image is bigger for example than 16M, it may over written the
| fdt blob which u-boot loaded to the DDR memory @0x11000000 with fdt_addr=0x11000000
|
| To expand the fdt_addr from 0x11000000 to 0x18000000, which can avoid the override
| Since we will not likely have one kernel image larger than 128MB.
`----
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
This adds following new targets:
- update_nand_kernel
- update_nand_fdt
- update_nand_filesystem
and to avoid confusion, the 'update_nand_full' has been renamed to
'update_nand_firmware_full'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This reads the kernel, ftd and boot into ubifs filesystem. While on
that, the SD firmware filename definition has been moved next to the
other SD related commands.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Using 512k for fdt partition allow it to be aligned with the other
small partitions and 512k erase block size.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.
Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add CONFIG_CMD_FUSE option, so that the fuse API can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch add uuid disk to defualt partions necessary to
restore gpt partitions and fixes mmcdev environmental variable.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When variable size SPL is used, the BL1 expects the SPL to be
encapsulated differently: instead of putting the checksum at a fixed
offset in the SPL blob, prepend the blob with a header including the
size and the checksum.
The enhancements include
- adding a command line option, '--vs' to indicate the need for the
variable size encapsulation
- padding the fixed size encapsulated blob with 0xff instead of random
memory contents
- do not silently truncate the input file, report error instead
- no need to explicitly closing files/freeing memory, this all happens
on exit; removing cleanups it makes code clearer
- profuse commenting
- modify Makefile to allow enabling the new feature per board
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding initial config for SMDK5420 to build and boot U-Boot
over Exynos based SMDK5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Beagleboard. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
The PXA incorrectly uses CONFIG_SYS_HZ, which should be 1000 across
U-Boot. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix the timeout issue after running "bootp" command in u-boot
console. For example you see "EHCI timed out on TD- token=0x...".
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10
after a controller reset and before RUN bit is set
(per technical reference manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
DT kernel requires CONFIG_OF_LIBFDT. 'bootm' needs to know DT location.
In addition, fix kernel console device and enable U-Boot long help.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Initial configuration has worng address of the second chip.
There is an alias for the 1st chip at 0x02000000 in earlier
verions of LP-8x4x, so the boot normally.
However, new LP-8x4xs have a bigger 1st flash chip, and hang on
boot without this patch.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
This patch adds support for the AMPIRE 800x480 LCD panel that is available
for M53EVK.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The CPU errata expressed in include/configs/mx6_common.h apply
to all i.MX6DQ and i.MX6DLS parts.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
According to the README:
"- CONFIG_SYS_SPD_BUS_NUM
If SPD EEPROM is on an I2C bus other than the first
one, specify here. Note that the value must resolve
to something your driver can deal with."
There is no SPD EEPROM on the imx boards, so ged rid of this option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add SATA support on uDoo Board.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
"ULPI: ulpi_reset: failed writing reset bit"
So, remove it.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
commit 16297cfb2a
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Fri Oct 4 19:22:26 2013 +0200
usb: new board-specific USB init interface
introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
