This patch fixes a problem with the RGMII setup of the 460GT. The 460GT
has 2 RGMII instances and we need to configure the 2nd RGMII instance
for the EMAC2+3 channels.
Signed-off-by: Stefan Roese <sr@denx.de>
fdt.c: In function 'ft_cpu_setup':
fdt.c:33: warning: implicit declaration of function 'do_fixup_by_prop_u32'
fdt.c:39: warning: implicit declaration of function 'do_fixup_by_compat_u32'
fdt.c:43: warning: implicit declaration of function 'fdt_fixup_ethernet'
fdt.c:45: warning: implicit declaration of function 'fdt_fixup_memory'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The fdt set command was treating properties specified as <00> and <0011>
as byte streams, rather than as an array of cells. As we already have
syntax for expressing the desire for a stream of bytes ([ xx xx ...]),
we should use the <> syntax to describe arrays of cells, which are always
32-bits per element. If we imagine this likely (IMHO) scenario:
> fdt set /ethernet-phy@1 reg <1>
With the old code, this would create a bad fdt, since the reg cell would be
made to be one byte in length. But the cell must be 4 bytes, so this would
break mysteriously.
Also, the dts spec calls for constants inside the angle brackets (<>)
to conform to C constant standards as they pertain to base.
Take this scenario:
> fdt set /ethernet@f00 reg <0xe250000\ 0x1000>
The old fdt command would complain that it couldn't parse that. Or, if you
wanted to specify that a certain clock ran at 33 MHz, you'd be required to
do this:
> fdt set /mydev clock <1f78a40>
Whereas the new code will accept decimal numbers.
While I was in there, I extended the fdt command parser to handle property
strings which are split across multiple arguments:
> fdt set /ethernet@f00 interrupts < 33 2 34 2 36 2 >
> fdt p /ethernet@f00
ethernet@f00 {
interrupts = <0x21 0x2 0x22 0x2 0x24 0x2>;
};
Lastly, the fdt print code was rearranged slightly to print arrays of cells
if the length of the property is a multiple of 4 bytes, and to not print
leading zeros.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
correctly configures the SATA/PCIe PHY for SATA usage when this jumper
is installed.
Signed-off-by: Stefan Roese <sr@denx.de>
finish off what commit 43ddd9c820,
"Remove deprecated CONFIG_OF_HAS_UBOOT_ENV and CONFIG_OF_HAS_BD_T"
started.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch makes SPARC/LEON processors able to read and write
to the SMC91111 chip using the chip external I/O bus of the memory
controller. This patchs defines the standard in and out macros
expected by the SMC9111 driver.
To access that I/O bus one must set up the memory controller
(MCTRL or FTMCTRL) correctly. It is assumed that the user sets
up this correctly when the other MCTRL parameters are set up. It
can be set up from the board configuration header file.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Replace AT91CAP9.h file with several splitted header files coming
from the Linux kernel.
This is part 2 of the replacement: more header imports and edits.
Signed-off-by: Stelian Pop <stelian@popies.net>
Replace AT91CAP9.h file with several splitted header files coming
from the Linux kernel.
This is part 1 of the replacement: pristine header files import.
Signed-off-by: Stelian Pop <stelian@popies.net>
AT91CAP9 and AT91SAM9 SoCs are very close hardware wise, so a
common infrastructure can be used. Let this infrastructure be
named after the AT91SAM9 family, and move the existing AT91CAP9
files to the new place.
Signed-off-by: Stelian Pop <stelian@popies.net>
The timer on AT91CAP9/AT91SAM9 is supplied by the SoC, and not by
the board, so use timer_init() instead of interrupt_init().
Signed-off-by: Stelian Pop <stelian@popies.net>
DataFlash partition information has become a mess. This patch
defines a single partition scheme for Atmel DataFlashes. This partition
scheme will be used by all AT91CAP9 and AT91SAM9 boards.
Signed-off-by: Stelian Pop <stelian@popies.net>
When the version_string function in start.S is not 4-byte align,
it will cause the compiler generates "unaligned opcodes detected
in executable segment". This issue affects all ColdFire CPUs.
By adding .align 4 after CONFIG_IDENT_STRING, it will pad 0's if
it is not aligned.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
Add support for the ptm1la, ptm1ms, ptm2la and ptm2ms
environment variables.
Cleanup pci_target_init.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many Atmel boards have no "real" (NOR) flash on board, and rely only
on DataFlash and NAND memories. This patch enables CFG_NO_FLASH to
be present in a board configuration file, while still enabling flash
commands like 'flinfo', 'protect', etc.
Signed-off-by: Stelian Pop <stelian@popies.net>
This punts the old spi flash driver for a new/generalized one until the
common one can be integrated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This fixes a naming bug for at91rm9200 lowlevel init code:
NOR boot flash is on chipselect 0, not chipselect 2. This
makes code use the register name from chip datasheets.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This fixes a naming bug for at91rm9200 lowlevel init code:
NOR boot flash is on chipselect 0, not chipselect 2. This
makes code use the register name from chip datasheets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add some missing ARM boards to MAKEALL. These build correctly,
unlike several of the boards already listed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
