Commit Graph

41616 Commits

Author SHA1 Message Date
Jagan Teki
3788b451e3 config: Move CONFIG_BOARD_LATE_INIT to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-21 15:12:33 -05:00
Jagan Teki
de70fefb1b common: Kconfig: Add BOARD_LATE_INIT entry
This patch add Kconfig entry for CONFIG_BOARD_LATE_INIT

Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-21 09:19:27 -05:00
Tom Rini
dec3030638 mx6saberesd_spl: Correct falcon mode addition
When falcon mode support was added, it was right around when SPL_OS_BOOT
was migrated to Kconfig.  So first we must move the enablement to the
defconfig file.  Next, it turned off EXT support rather than add the
information to allow for falcon mode from EXT.  Add this information so
that the board compiles after 5d28b930f2.

Fixes: d96796ca23 ("mx6sabresd: Add Falcon mode support")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-20 19:55:53 -05:00
Emmanuel Vadot
995eab8b5b bootm: qnx: Disable data cache before booting QNX image
Instead of disabling the data cache in the bootelf command, disabling
it in the do_bootm_qnxelf function.
Some ELF binary might want the cache enabled.

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
2017-01-20 15:38:05 -05:00
Sven Ebenfeld
b4e923a805 tools: mkimage: fix sizeof_mismatch found by coverity
Reported-by: Coverity (CID: 155214)
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
2017-01-20 15:38:04 -05:00
Lokesh Vutla
fc4dd72eb6 ARM: OMAP5+: Remove unsed dpll structures
Latest gcc compile strted complaining about defined structure definition
that are not used. Remove the unused sturctures.

Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-01-20 15:38:04 -05:00
Lokesh Vutla
584a69cb5e ARM: OMAP4: Fix compiler warning
Latest gcc 6.2 compiler is throwing the below warning for omap4_panda_defconfig
arch/arm/mach-omap2/omap4/hw_data.c:136:3: warning: 'abe_dpll_params_sysclk_196608khz' defined but not used [-Wunused-const-variable=]
   abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {

Fix this by guarding it with CONFIG_SYS_OMAP_ABE_SYSCK

Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-01-20 15:38:03 -05:00
Emmanuel Vadot
80d2ae5e1f binman: add tools directory to the python path
The built _libfdt.so is placed in the /tools dir and need to say here
as it contains relative paths.
Add the directory to the python path so binman can use this module.

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
2017-01-20 15:38:03 -05:00
Emmanuel Vadot
1905c8fc71 build: Always build the libfdt python module
Do not rely on CONFIG_SPL_OF_PLATDATA to build the libfdt python module.
If swig is present, this will be build

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
2017-01-20 15:38:03 -05:00
Lukasz Majewski
56acf018c1 MAINTAINERS: DFU: Change e-mail address of DFU maintanier
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-01-20 15:38:02 -05:00
Andreas Färber
70b8bd7d3b odroid-c2: Enable distro boot
Use the generic "distro" boot framework to enable automatic DHCP boot.
MMC and USB are not yet implemented, so this is the only boot option.

The fdt and kernel addresses are adopted from downstream; ramdisk and
scriptaddr addresses were chosen arbitrarily.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
2017-01-20 15:38:02 -05:00
Andreas Färber
8c9bfc47ed meson: misc_init_r is board-specific
Move it from meson-gxbb-common.h to odroid-c2.h to allow new boards not
to implement it.

Signed-off-by: Andreas Färber <afaerber@suse.de>
2017-01-20 15:38:02 -05:00
Tom Rini
c67c8c604b board_init.c: Always use memset()
We can make the code read more easily here by simply using memset()
always as when we don't have an optimized version of the function we
will still have a version of this function around anyhow.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-20 15:38:01 -05:00
Tom Rini
40d5534cff ARM: Default to using optimized memset and memcpy routines
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel.  We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase.  However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.

Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-20 15:38:01 -05:00
Andrew F. Davis
a4a35934c7 mach-omap2: Fix secure boot media generation
While moving OMAP related files to mach-omap2 the functionality
relating to generating secure boot files was modified. This change
prevents secure platforms other than AM33xx and OMAP54XX from
correctly building files for all needed media types.

Fixes: 983e37007d ("arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-01-20 15:38:00 -05:00
Andrew F. Davis
cf947da19a spl: Add some missing newlines
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
2017-01-20 15:38:00 -05:00
Andrew F. Davis
5d28b930f2 spl: Remove inline ifdef check for EXT and FAT support
These files are only included for build by the make system
when CONFIG_SPL_{EXT,FAT}_SUPPORT is enabled, remove the unneed
checks for these in the source files.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-20 15:37:59 -05:00
xypron.glpk@gmx.de
cec85d4e00 common/image.c: Use correct suffixes for binary sizes
IEC 80000-13:2008 Quantities and units
Part 13: Information science and technology

defines the prefixes to use for binary multiples.

So instead of writing
Data Size:    6726132 Bytes = 6568.49 kB = 6.41 MB
in dumpimage we should write
Data Size:    6726132 Bytes = 6568.49 KiB = 6.41 MiB.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-01-20 15:37:59 -05:00
Emmanuel Vadot
d3e8f63026 api: storage: Test all block device in dev_stor_get
In a config with one MMC at device id '1' and no MMC at device id '0'
(a BeagleBone Black with no sd inserted for example), the current code
will first test to access the MMC 0 (sd port), seeing that no device is
present it will simply return that no more device are present for this
class.
This patch fixes this by testing all devices for each class.

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
2017-01-20 15:37:58 -05:00
Emmanuel Vadot
6215bd4c1f api: Use hashtable function for API_env_enum
The current code can loop undefinitly as it doesn't parse
correctly the env data.
Since the env is an hashtable, use the hashtable function for
the API_ENV_ENUM api call.

Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-20 09:15:24 -05:00
Sébastien Szymanski
6baa692f90 cmd/host: add missing \n in help text
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-01-20 09:15:24 -05:00
Adam Ford
476e16e87e ARM: omap3_logic: Refactor Boot Environmental variables
Some scripts are calling the same functions, so these changes consolidate
common scripts together to reduce redundancy and shrink size a bit.  This
also keeps the 'bootargs' variable from growing if manually called more
than one time. This also adds NAND booting scripts based on newly consolidated
scripts.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-01-20 09:15:24 -05:00
Rick Altherr
c2e7e72bb9 bootm: relocate ramdisk if CONFIG_SYS_BOOT_RAMDISK_HIGH set
In 35fc84f, bootm was refactored so plain 'bootm' and
'bootm <subcommand>' shared a common implementation.
The 'bootm ramdisk' command implementation is now part of the common
implementation but not invoke by plain 'bootm' since the original
implementation never did ramdisk relocation.  Instead, ramdisk
relocation happened in image_setup_linux() which is typically called
during the OS portion of 'bootm'.

On ARM, parameters to the Linux kernel can either be passed by FDT or
ATAGS. When using FDT, image_setup_linux() is called which also triggers
ramdisk relocation.  When using ATAGS, image_setup_linux() is _not_
called because it mostly does FDT setup.

Instead of calling image_setup_linux() in both FDT and ATAGS cases,
include BOOTM_STATE_RAMDISK in the requested states during a plain
'bootm' if CONFIG_SYS_BOOT_RAMDISK_HIGH is set and remove the ramdisk
relocation from image_setup_linux().  This causes ramdisk relocation to
happen on any system where CONFIG_SYS_BOOT_RAMDISK_HIGH regardless of
the OS being booted. Also remove IMAGE_ENABLE_RAMDISK_HIGH as it was
only used by the now-removed code from image_setup_linux().

Signed-off-by: Rick Altherr <raltherr@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
2017-01-20 09:15:20 -05:00
Heiko Schocher
17fa032671 serial, ns16550: bugfix: ns16550 fifo not enabled
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.

Since the above patch, you have to setup the fcr register.

For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...

This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.

Detected this issue with automated tbot tests on am335x
based shc board.

The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)

Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-20 09:15:19 -05:00
Tom Rini
0675f992db Merge git://git.denx.de/u-boot-fsl-qoriq 2017-01-19 12:22:23 -05:00
Yangbo Lu
5e4a6db8f4 armv8: ls1012a: define esdhc_status_fixup for RDB board
On LS1012ARDB board, three dual 1:4 mux/demux devices drive the SDHC2
signals to eMMC, SDIO wifi, SPI and Ardiuno shield. Only when we select
eMMC and SDIO wifi, the SDHC2 could be used. Otherwise, the command
inhibit bits of eSDHC2_PRSSTAT register will never release. This would
cause below continious error messages in linux since it uses polling
mode to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for RDB to disable
SDHC2 status if no SDIO wifi or eMMC is selected.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:46:52 -08:00
Yangbo Lu
208e1ae8d1 armv8: ls1012a: define esdhc_status_fixup for QDS board
The LS1012AQDS board has a hardware issue. When there is no eMMC
adapter card inserted in SDHC2 adapter slot, the command inhibit
bits of eSDHC2_PRSSTAT register will never release. This would cause
below continious error messages in linux since it uses polling mode
to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for QDS to
disable SDHC2 status if no eMMC adapter card is detected.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:46:45 -08:00
Yangbo Lu
fce1e16c55 mmc: fsl_esdhc: move 'status' property fixup into a weak function
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:46:30 -08:00
Hou Zhiqiang
b595662ab9 fsl PPA: enable PPA for ls1043ardb and ls1046ardb
Enable PPA for ls1043ardb NOR boot and ls1046ardb QSPI boot.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:44:56 -08:00
Hou Zhiqiang
0541527bde kconfig: fsl PPA: move CONFIG_* to Kconfig
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:43:25 -08:00
Hou Zhiqiang
daa926448c ARMv8/sec_firmware: relocated and renamed the config FSL_PPA_ARMV8_PSCI
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:39:51 -08:00
Hou Zhiqiang
0897eb2ced kconfig: armv8: move armv8 sec_firmware CONFIG_* to Kconfig
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York S: clean up scripts/config_whitelist.txt]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:35:53 -08:00
Alison Wang
7c5e1feb1d armv8: aarch64: Fix the warning about x1-x3 nonzero issue
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:33 -08:00
Wenbin Song
2ca84bf7b2 armv8/fsl-layerscape: fdt: fixup LS1043A rev1 MSI node
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:27 -08:00
Wenbin Song
fa18ed7658 armv8/ls1043a: fixup GIC offset for ls1043a rev1
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.

The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.

If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.

Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.

The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:21 -08:00
Tang Yuantian
435cca1671 armv8: fsl-lsch3: enable snoopable sata read and write
By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions.  This patch enable it in the
sata axicc register.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:17 -08:00
Hou Zhiqiang
dccef2ec01 ls1046ardb: Add support power initialization
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:13 -08:00
Hou Zhiqiang
031acdbae8 armv8/fsl_lsch2: Add chip power supply voltage setup
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.

Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:08 -08:00
Hou Zhiqiang
6424577b1b ls1046ardb: cpld: add API for selecting core volt
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:29:02 -08:00
Hou Zhiqiang
4394ad1227 pmic: pmic_mc34vr500: Add APIs to set/get SWx volt
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:57 -08:00
Hou Zhiqiang
762161b04a pmic: pmic_mc34vr500: Add a driver for the mc34vr500 pmic
This patch adds a simple pmic driver for the mc34vr500 pmic which
is used in conjunction with the fsl T1 and LS1 series SoC.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:53 -08:00
York Sun
9cfab06e79 armv8: fsl-layerscape: Fix SECURE_BOOT config
Without a prompt in Kconfig, SECURE_BOOT cannot be selected by
defconfig. The option was dropped unintentionally when defconfig
files were cleaned up. Three targets were impacted
ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT,
ls2080aqds_SECURE_BOOT.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-01-18 09:28:44 -08:00
Udit Agarwal
9ed44787f6 LS2080A: Add validation of MC & DPC images.
Add secure boot validation of MC, DPC images using
esbc_validate command.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:39 -08:00
Udit Agarwal
39199356e9 SECURE_BOOT: Update bootscript and its hdr addresses
Update bootscript and its hdr addresses for Layerscape Chasis 3
based platforms instead of individual SoCs.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:34 -08:00
Yangbo Lu
cda000f3c3 configs: ls1012a: enable driver model for eSDHC
Enable driver model for eSDHC on ls1012a rdb and qds boards.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:30 -08:00
Yangbo Lu
e1f39751d5 armv8: ls1012a: add eSDHC nodes
This patch is to add eSDHC nodes for ls1012a.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:25 -08:00
Yangbo Lu
a6473f8e3f mmc: fsl_esdhc: add 'fsl, esdhc' into of_match table
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:20 -08:00
Yangbo Lu
fc8048a88e mmc: fsl_esdhc: make GPIO support optional
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:14 -08:00
Hou Zhiqiang
3564208e01 armv8/fsl-lsch3: consolidate the clock system initialization
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:09 -08:00
Hou Zhiqiang
904110c7ac armv8/fsl-lsch2: refactor the clock system initialization
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.

This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:27:59 -08:00