Instead of always using the largest blocksize the card supports, check
if it can support smaller block sizes and use 512 bytes if possible.
Most cards do support this, and other parts of u-boot seem to have
trouble with block sizes different from 512 bytes.
Also enable underrun/overrun protection.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
The update procedure was modified to turn off the USB subsystem
before exit for MCC200 and TRAB. This is necessary as otherwise the
USB controller continues to write periodically to system memory!
MCC200-specific notes:
- the patch disables the magic key check for MCC200
- the patch contains the configuration changes made
for the new revision of the board.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The last fdt patch to bootm did board setup based on the address
specified by a prior fdt address command invocation. The bootm
code, as its call to fdt_chosen does, should use the fdt specified
by the user on the bootm command. Note this restores full
functionality for the 8360's existing default boot environment
values, e.g. 'run nfsboot' (i.e. no having to 'fdt addr $fdtaddr'
before booting a kernel).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In the patch titled "Create new fdt boardsetup command..." I removed the
call to ft_board_setup() from the routine fdt_chosen(), but I forgot
to add a direct call back into cmd_bootm.c
This fixes the oversight by adding the direct call to the bootm command.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Previously ft_board_setup() was called by fdt_chosen() which was not
really correctly structured. This splits ft_board_setup() out by creating
a new fdt boardsetup command.
Fix a bug when parsing fdt set command values which have the square
bracket form [00 11 22 33] - the length was updated incorrectly in when
parsing that form.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
The fdt_chosen() function was adding/seting some properties ad-hoc
improperly and duplicated (poorly) what was done in ft_board_setup()
Clean up long lines (setting properties, printing errors).
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
The new name matches more closely the kernel's name, which is also
a much better description.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Break lines that were greater than 80 characters in length.
Move the fdt print and property parsing code to separate static functions
to reduce coding clutter in the fdt_cmd handling body.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Do *NOT* return after the "point of no return" has been passed.
If something goes wrong, the board must be reset after that point.
Move the "Transferring control to Linux" debug message back to where it
belongs: just before transferring control to linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Make the length parameter optional: if not specified, do the move using
the current size unchanged.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Declare the variable fdt properly as extern.
Call the "set_fn" function pointer the "short way" without the full
dereferencing syntax.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Print more than the raw libfdt error message strings. This is especially
useful for cluing in the user when the bootm command aborts due to
blob problems.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This is the way u-boot reduces configured-out code. At Wolfgang
Grandegger and Wolfgang Denk's request, make libfdt conform.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
Use generic 64bit division in nand_util.c. This makes nand_util.c
independent of any toolchain 64bit division.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Move the 64bit division from lib_avr32 to lib_generic. With this, all
boards can do_div/__div64_32 if needed, not only avr one. Code is put
to lib_generic, so no larger memory footprint if not used. No code
modifications. Thanks for proposal by Håvard Skinnemoen.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
make: *** No rule to make target `/work/wd/tmp/board/mpc8349itx/u-boot.lds', needed by `/work/wd/tmp/u-boot'. Stop.
Both the ITX and ITX-GP fail when you use "make O=<some dir> ..." or
"BUILD_DIR=<some dir> ./MAKEALL ..."
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the README for DDR ECC, change the name
to README.mpc83xx.ddrecc.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Remove the duplicated source code of ecc command on the <board>.c,
for reused, move these code to cpu/mpc83xx directory.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
..and not the global fdt. Rename local fdt vars to blob so as not to
be confused with the global var with the same three-letter name.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>