mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPD autodetection hasn't been enabled that's why there is zero size
difference if that options are enabled/disabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, ospi and mmc.
The distro boot commands now reads the script from flash offset
of 63.5MB for qspi and ospi and executes it. For mmc its same
as generic distro boot command. As either one of the qspi or ospi can
exist on hardware, defined a single distroboot command as xspi
that works for both.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards for qspi, ospi for now.
512kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This platform is going to become generic that's why it is necessary also
enable different PHY vendors.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new config option which is used for
reserving a specific memory for MMU Table and in this
case we are using TCM for that purpose.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
For example:
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=g6l7
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2019-02-13
Goodness this time around:
- HII protocol, finally allows us to run the UEFI Shell!
(experimantal, disabled by default)
- efi selftest now available on Cortex-M
- NVMe support for distro boot
- Lots of code cleanup
We check the existence of files with fs_exist(). This function calls
fs_close(). If we do not set the active block device again fs_opendir()
fails and we do not set the flag EFI_FILE_DIRECTORY. Due to this error the
`cd` command in the EFI shell fails.
So let's add the missing set_blk_dev(fh) call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We have to ensure while printing UTF16 strings that we do not exceed the
end of the print buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich ran into issues with HII and iPXE which lead to #SErrors on
his Odroid-C2 system. We definitely do not want to regress just yet,
so let's not expose the HII protocols by default.
Instead, let's make it a config option that people can play with
This way, we can stabilize the code in tree without breaking any
users.
Once someone figures out, why this breaks iPXE (probably a NULL
dereference), we can enable it by default.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
---
v1 -> v2:
- Remove HII selftest as well
v2 -> v3:
- Make config option
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
For correct indention use EFI_PRINT() instead of debug().
For printing efi_uintn_t or size_t use the %zu or %zx format code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_st_printf() does not support format code %ld. Anyway the format code
for size_t would be %zu which isn't supported either.
We do not want any divisions to avoid invalid references to integer
arithmetic routines, cf.
https://gcc.gnu.org/onlinedocs/gccint/Integer-library-routines.html.
As a simple remedy remove the noisy messages from the output.
They are not relevant for automated testing.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This efi_selftest tests HII database protocol and HII string protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch is a place holder for HII configuration routing protocol and
HII configuration access protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling keyboard layout package in HII database protocol.
A package can be added or deleted in HII database protocol, but
we don't set 'current' keyboard layout as there is no driver that
requests a keyboard layout.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling GUID package in HII database protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides enough implementation of the following protocols to
run EDKII's Shell.efi and UEFI SCT:
* EfiHiiDatabaseProtocol
* EfiHiiStringProtocol
Not implemented are:
* ExportPackageLists()
* RegisterPackageNotify()/UnregisterPackageNotify()
* SetKeyboardLayout() (i.e. *current* keyboard layout)
HII database protocol in this patch series can handle only:
* GUID package
* string package
* keyboard layout package
(The other packages, except Device path package, will be necessary
for interactive and graphical UI.)
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
arch/x86/lib/string.c contains assembler implementations of memcpy(),
memmove(), and memset() written for i386. Don't use it on x86_64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Our implementation of GetNextVariableName() relies on
CONFIG_REGEX=y. So EFI_LOADER has to select it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Our current implementation of GetNextVariableName() first collects all EFI
variables. If none is found at all hexport_r() returns a zero length string
terminated by \0 and the value 1 as number of bytes in the returned buffer.
In this case GetNextVariableName() has to return EFI_NOT_FOUND.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Symbolic links are not supported on all file systems, e.g. not on FAT. So
it is not wise to use them in our source tree.
Use a qualified path to refer to lib/efi_loader/efi_freestanding.c in
scripts/Makefile.lib instead.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build with O=]
Signed-off-by: Alexander Graf <agraf@suse.de>
Helloworld does not need its own memcpy() implementation anymore. Use the
one provided in efi_freestanding.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
