Commit Graph

50 Commits

Author SHA1 Message Date
Tom Rini
6e7d7aa2e2 Merge branch 'next'
Merge all outstanding changes from the current next branch in now that
we have released.
2020-07-06 15:46:38 -04:00
Tom Rini
c5a6e9f8b8 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 13:54:25 -04:00
Lukasz Majewski
56c4046038 spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29 13:34:43 -04:00
Tom Rini
e985eb14ac Convert CONFIG_CMD_ASKENV et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04 18:10:02 -04:00
Tom Rini
35e3991d91 Convert CONFIG_CMD_MMC to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_MMC

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-25 11:54:53 -04:00
Tom Rini
5bec37eb72 Merge branch 'migrate-various-PHY-options'
- Finish migration of CONFIG_PHYLIB and a number of related symbols to
  defconfig files.
2020-04-28 16:41:00 -04:00
Tom Rini
556fd590db configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 16:15:47 -04:00
Tom Rini
306881a0bf Convert CONFIG_PHYLIB et al to Kconfig
This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 15:57:58 -04:00
Tom Rini
4244429ff0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-06 13:42:52 -05:00
Biwen Li
9ebde8849a dm: arm: ls1021a: add i2c DM support
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04 16:20:25 +05:30
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Alison Wang
5d168adf2b configs: Enable SPL_FSL_PBL for some LayerScape platforms
In commit <db4080d56dec>, SPL_FSL_PBL is removed from the configs of
some LayerScape platforms. Actually, SPL_FSL_PBL is needed for SD/NAND
boot on LS1021A/LS1043A/LS1046A to create boot binary having SPL binary
in PBI format concatenated with u-boot binary. SPL_FRAMEWORK is used on
these platforms too.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Miquel Raynal
888f184abe mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD
Like in Linux, just use CONFIG_MTD to compile the MTD stack.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
665c35a764 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 11:47:37 -04:00
Tom Rini
db4080d56d configs: Migrate the various SPL_BOOT_xxx choices for PowerPC
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT.  Migrate this to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-14 16:10:49 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Peng Ma
b0d4a85475 configs: ls1021a: enable sata configs for all ls1021a defconfigs
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a
defconfigs that missing one of them or more.
enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK
Support sata for all ls1021a defconfigs

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:44 +05:30
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Alex Kiernan
eedecb0fe8 Cleanup CONFIG_SPL_SERIAL_SUPPORT migration
CONFIG_SPL_SERIAL_SUPPORT had already been migrated to Kconfig, but
existed in some include files; fix those up here.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-28 18:32:22 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Mario Six
07dea2e737 treewide: Migrate CONFIG_FSL_ESDHC to Kconfig
Migrate the CONFIG_FSL_ESDHC option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 18:31:05 -04:00
Mario Six
171510522e treewide: Migrate CONFIG_TSEC_ENET to Kconfig
Migrate the CONFIG_TSEC_ENET option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 15:12:53 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Tom Rini
fa2c14676c configs: Re-sync with CONFIG_DISTRO_DEFAULTS
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS.  As they plainly intended to, set that flag and
re-sync config files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 10:21:41 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tom Rini
308e066566 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-16 21:35:43 -04:00
Fabio Estevam
4912551bb0 armv7: ls1021aiot: Move CONFIG_CMD_BOOTZ to Kconfig
CONFIG_CMD_BOOTZ symbol does not work in board config file
anymore, so fix this by moving it to Kconfig.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-09 08:48:44 -07:00
Tom Rini
ecad7051b0 configs: Migrate all of the existing USB symbols, except fastboot
This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files.  This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB.  Leaving this as-is results in a build failure, and
without work, run time failure.  The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot.  The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:20 -04:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Tom Rini
1989374b21 configs: Finish migration of PHY_GIGE
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-08 17:02:31 -04:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Tom Rini
285226785e Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs
In some cases this is absolutely required, so select this for some secure
features.  This also requires migration of RSA_FREESCALE_EXP

Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 11:37:24 -05:00
Patrick Delaunay
b331cd6204 cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT
We convert CONFIG_PARTITION_UUIDS to Kconfig first.  But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-28 08:48:03 -05:00
Patrick Delaunay
bd42a94268 disk: convert CONFIG_EFI_PARTITION to Kconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-28 08:47:42 -05:00
Patrick Delaunay
b0cf733933 disk: convert CONFIG_DOS_PARTITION to Kconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-28 08:47:34 -05:00
Simon Glass
a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Jagan Teki
3788b451e3 config: Move CONFIG_BOARD_LATE_INIT to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-21 15:12:33 -05:00
Minghuan Lian
8808aeb7a9 arm: ls1021a: Enable PCIe in defconfigs
The patch enables PCIe in ls1021a defconfigs and
removes unused PCIe related macro defines.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:26:47 -08:00
Masahiro Yamada
187809517d Sync defconfig files by savedefconfig
Generated by "tools/moveconfig -s".

This will make config moves easier.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-29 13:07:33 -05:00
York Sun
f9dd8553f3 armv7: ls1021aiot: Fixing SPL compiling issues
To align with SPL change 38fed8ab and 693d4c9f, add Kconfig option
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to defconfig, and remove
CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Feng Li <feng.li_2@nxp.com>
2016-11-23 10:39:41 -08:00
Feng Li
20c700f8da armv7: Add support of ls1021a-iot board
The patch adds support for Freescale ls1021a-iot board.

Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00