Commit Graph

44 Commits

Author SHA1 Message Date
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
James Byrne
77b508d34b net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together
Commit d397f7c45b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-05-14 14:43:33 -05:00
Alex Kiernan
623de3f086 Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

  xilinx_zynqmp_zc1275_revB
  xilinx_zynqmp_zc1751_xm018_dc4
  xilinx_zynqmp_zc1751_xm019_dc5
  xilinx_zynqmp_zcu100_revC
  xilinx_zynqmp_zcu102_rev1_0
  xilinx_zynqmp_zcu102_revA
  xilinx_zynqmp_zcu102_revB
  xilinx_zynqmp_zcu104_revA
  xilinx_zynqmp_zcu104_revC
  xilinx_zynqmp_zcu106_revA
  xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-04 13:04:12 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Fabio Estevam
0a112072bb pico-imx6ul: Convert to DM_PMIC
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.

Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-13 09:14:35 +01:00
Fabio Estevam
cad779c0a4 pico-imx6ul: Convert to CONFIG_DM_GPIO
Convert to CONFIG_DM_GPIO.

Also, DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation, so do as requested.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-13 09:14:35 +01:00
Fabio Estevam
737d8bd820 pico-imx6ul: Convert to DM MMC
Select CONFIG_DM_MMC=y in order to support MMC driver model.

This allows the MMC board related code to be removed.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-13 09:14:35 +01:00
Fabio Estevam
1db0e414e3 pico-imx6ul: Select CONFIG_OF_CONTROL
Select CONFIG_OF_CONTROL and the appropriate device tree files
in preparation for converting to driver model.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-13 09:14:35 +01:00
Philipp Tomsich
2acc24fc28 Kconfig: Migrate BOUNCE_BUFFER
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.

This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).

This commit includes a full migration using moveconfig.py to ensure
that each commit compiles.  To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.

[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
2019-01-19 09:49:26 -05:00
Jean-Jacques Hiblot
f811e9763f Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGET
The SPL option for USB gadget should be named after the option for u-boot
(CONFIG_USB_GADGET)

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-10 18:52:55 +01:00
Tom Rini
1bac199e8c configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07 18:11:00 -05:00
Otavio Salvador
9ddd1cd596 pico-imx6ul: Add Falcon mode support
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.

As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:22:52 +02:00
Otavio Salvador
f6d805504b pico-imx6ul: Add bootmenu to choose the baseboard
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Otavio Salvador
136f460565 pico-imx6ul: Sync defconfig with new changes
Due the changes in previous commits, we need to resync the defconfig
to reduce noise in next commits.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Fabio Estevam
558a37ce85 pico-imx6ul: Add bmode support
The 'bmode' command is helpful for switching the boot media.

In the case of pico-imx6ul there are two possible boot media:
eMMC or USB.

To boot from eMMC:

=> bmode emmc

To boot from USB (via Serial Download Protocol):

=> bmode usb

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Fabio Estevam
3e8cdb990c pico-imx6ul: Add fastboot support
fastboot tool is a convenient way to flash the eMMC, so
add support for it.

Examples of usages:

On the pico-imx6ul U-Boot prompt:

=> fastboot 0

On the Linux PC connected via USB:

1. Retrieving the U-Boot version

$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc2-00130-g0881835-dirty
finished. total time: 0.000s

2. Resetting the board

$ sudo fastboot reboot -i 0x0525

(this causes the pico-imx6ul to reboot)

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Fabio Estevam
82a8a93327 pico-imx6ul: Convert to SPL
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.

Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.

Currently only the 256MB is tested/supported.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:24 +02:00
Fabio Estevam
636941ff4d pico-imx6ul: Convert to distro config
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14 15:04:17 +02:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Mario Six
07dea2e737 treewide: Migrate CONFIG_FSL_ESDHC to Kconfig
Migrate the CONFIG_FSL_ESDHC option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 18:31:05 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Fabio Berton
ebbdeb2a10 pico-imx6ul: Add function to create gpt partitions
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.

Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2017-11-20 09:54:09 +01:00
Fabio Berton
65551e389a pico-imx6ul: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.

Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-20 09:54:09 +01:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Maxime Ripard
a95aee6af7 usb: gadget: Make g_dnl USB settings common
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.

Make them common by renaming them, and convert all the users.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Alexandru Gagniuc
da3b9e7fd6 Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:29 -05:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Simon Glass
218257b01a Convert CONFIG_CMD_BMODE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BMODE

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:30:06 -04:00
Simon Glass
a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00
Masahiro Yamada
187809517d Sync defconfig files by savedefconfig
Generated by "tools/moveconfig -s".

This will make config moves easier.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-12-29 13:07:33 -05:00
Jagan Teki
d259c00845 config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Tom Rini
6828e602b7 dfu: Migrate to Kconfig
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2016-09-27 10:46:45 -04:00
Tom Rini
645176d1d5 configs: Migrate CONFIG_USB_STORAGE
In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09 14:59:35 -04:00
Vanessa Maegima
af07d1544e pico-imx6ul: Add DFU support
DFU is a convenient way to program U-boot binary into the eMMC.

Add support for it.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12 17:58:49 +02:00
Tom Rini
7802ce910b configs: Re-sync BOOTDELAY changes
With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.

Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-17 09:34:49 -04:00
Fabio Estevam
83b6a43e6e pico-imx6ul: Select CONFIG_HUSH_PARSER option
Select CONFIG_HUSH_PARSER option in order to fix the following
problem:

Unknown command 'if' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'

Reported-by: Daiane Angolini <daiane.angolini@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Daiane Angolini <daiane.angolini@nxp.com>
2016-05-20 20:42:57 -04:00
Tom Rini
fc6e3c81de pico-imx6ul: Update the defconfig
The defconfig/config.h file were merged but were already out of sync
with mainline.  This brings them further into line now.

Cc: Richard Hu <richard.hu@technexion.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25 18:03:48 -04:00
Fabio Estevam
69cc7dbf1f Add initial support for Technexion's PICO-IMX6UL-EMMC board
Add support for Technexion's PICO-IMX6UL-EMMC board.

For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc

Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19 16:37:36 +02:00