Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Remove old values from kmp204x.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+NMmQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLnEB/0cWFfjDfCMY1o7R4QX
DeDRlD6k6acQWlwa5EiRKwpbPMJKrSI/m5alMCYZG6YHvGtzihqnqohz3gl1sepi
W7eyyyFsM4hqe4P3lSETJRGWe/O8bNkoa0hBzqZ9btqw2OJLBu4JYB+zKgz8kaDY
jzkGLgaaK6wtG3rEu+q4fjzp1y9kuz31WnN+9qS8jd/9UH13XKCkJl9TfY5pLfgc
mmbn2NWtAhi91uShcnIsOpLaNm23IV0ITa22etB9F1docZuUrbhOtiIF45AADjpG
/xtkV3dEVGml3N/17RizgOwxX3xughG0ak9xifsK6tfgqfVhaGMgkToNNBM+1ddm
rZZM
=hF12
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unused.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In prepartion to remove CONFIG_DEFAULT_CONSOLE, fold the current users.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These are all unused.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These comments are relict for old, now removed config options.
So remove these obsoleted comments too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose) and get rid of the
definition of overlayaddr..
Signed-off-by: Nishanth Menon <nm@ti.com>
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose).. we will get rid of
overlayaddr later in the series.
Signed-off-by: Nishanth Menon <nm@ti.com>
Currently we hard-code the number and initial addresses of QEMU's flash
banks, even though our code is perfectly able to gather the same
information from the DTB provided by QEMU.
This is especially annoying, since we have two slightly different
U-Boot configurations ("bare-metal" vs. loaded via Arm Trusted
Firmware), which need to be selected at build time.
Drop the two hard coded alternatives, and use
CONFIG_SYS_MAX_FLASH_BANKS_DETECT instead, which relies on the DTB to
figure out the actual flash configuration at runtime.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Signed-off-by: Stefan Roese <sr@denx.de>
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Increase max gunzip size, required for booting itb recovery images on
uDPU.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: andy.tang@nxp.com
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END