Since BayTrail, Intel starts to use new GPIO IPs in their chipset.
This adds the GPIO ASL, so that OS can load corresponding drivers
for it. On Linux, this is BayTrail pinctrl driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BayTrail integrates an internal ns15550 compatible UART (PNP0501).
Its IRQ is hardwired to IRQ3 in old revision chipset, but in newer
revision one IRQ4 is being used for ISA compatibility. Handle this
correctly in the ASL file.
Linux does not need this ASL, but Windows need this to correctly
discover a COM port existing in the system so that Windows can
show it in the 'Device Manager' window, and expose this COM port
to any terminal emulation application.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before moving 'current' pointer during ACPI table writing, we always
check the table length to see if it is larger than the table header.
Since our purpose is to generate valid tables, the check logic is
always true, which can be avoided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The generated AmlCode[] from IASL already has the calculated DSDT
table checksum in place. No need for us to calculate it again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per ACPI spec, during ACPI OS initialization, OSPM can determine
that the ACPI hardware registers are owned by SMI (by way of the
SCI_EN bit in the PM1_CNT register), in which case the ACPI OS
issues the ACPI_ENABLE command to the SMI_CMD port. The SCI_EN bit
effectively tracks the ownership of the ACPI hardware registers.
However since U-Boot does not support SMI, we report all 3 fields
in FADT (SMI_CMD, ACPI_ENABLE, ACPI_DISABLE) as zero, by following
the spec who says: these fields are reserved and must be zero on
system that does not support System Management mode.
U-Boot seems to behave in a correct way that the ACPI spec allows,
at least Linux does not complain, but apparently Windows does not
think so. During Windows bring up debugging, it is observed that
even these 3 fields are zero, Windows are still trying to issue SMI
with hardcoded SMI port address and commands, and expecting SCI_EN
to be changed by the firmware. Eventually Windows gives us a BSOD
(Blue Screen of Death) saying ACPI_BIOS_ERROR and refuses to start.
To fix this, turn on the SCI_EN bit by ourselves. With this patch,
now U-Boot can install and boot Windows 8.1/10 successfully with
the help of SeaBIOS using legacy interface (non-UEFI mode).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we already reserved high memory for configuration tables,
call high_table_malloc() to allocate tables from the region.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When SeaBIOS is on, reserve configuration tables in reserve_arch().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of asking each platform to provide reserve_arch(),
supply it in arch/x86/cpu/cpu.c in a unified way.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when CONFIG_SEABIOS is on, U-Boot allocates configuration
tables via normal malloc(). To simplify, use a dedicated memory
region which is reserved on the stack before relocation for this
purpose. Add functions for reserve and malloc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIRQ routing table checksum is fixed up in copy_pirq_routing_table(),
which is fine if we only write the configuration table once. But with
the SeaBIOS case, when we write the table for the second time, the
checksum will be fixed up to zero per the checksum algorithm, which
is caused by the checksum field not being zero before fix up, since
the checksum has already been calculated in the first run.
To fix this, move the checksum fixup to create_pirq_routing_table(),
so that copy_pirq_routing_table() only does what its function name
suggests: copy the table to somewhere else.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present board_final_cleanup() is called before booting a Linux
kernel. This actually needs to be done before booting anything,
like SeaBIOS, VxWorks or Windows.
Move the call to last_stage_init() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename qemu/acpi_table.c to qemu/e820.c, because ACPI stuff is moved
to qfw core, this file only contains code for installing e820 table.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Loading ACPI table from QEMU's fw_cfg interface is not x86 specific
(ARM64 may also make use of it). So move the code to common place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make file names consistent with CONFIG_QFW and CONFIG_CMD_QFW
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds some comments about qfw register endianness for clarity.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original implementation of qfw includes several x86 specific
operations, like directly calling outb/inb and using some inline
assembly code which prevents it being ported to other architectures.
This patch adds callback functions and moves those to arch/x86/
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch splits qfw command interface and qfw core function into two
files, and introduces a new Kconfig option (CONFIG_QFW) for qfw core.
Now when qfw command interface is enabled, it will automatically select
qfw core. This patch also makes the ACPI table generation select
CONFIG_QFW.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch is part of the qfw refactor work.
The qemu_fwcfg_free_files() function is only used in error handling in
ACPI table generation, let's not make this a core function and move it
to the right place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_GENENRATE_ACPI_TABLE controls the generation of ACPI table which
uses U-Boot's built-in methods and CONFIG_QEMU_ACPI_TABLE controls whether
to load ACPI table from QEMU's fw_cfg interface.
But with commit "697ec431469ce0a4c2fc2c02d8685d907491af84 x86: qemu: Drop
our own ACPI implementation", there is only one way to support ACPI table
for QEMU targets which is the fw_cfg interface. Having two Kconfig options
for this purpose is not necessary any more, so this patch consolidates
the two.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Move the command portion of arch/x86/cpu/qemu/fw_cfg.c into
cmd/qemu_fw_cfg.c
- Move arch/x86/include/asm/fw_cfg.h to include/qemu_fw_cfg.h
- Rename ACPI table portion to arch/x86/cpu/qemu/acpi_table.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
FADT/MADT tables are platform specific. Generate them for BayTrail.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds basic BayTrail platform ASL files. They are intended to be
included in dsdt.asl of any board that is based on this platform.
Note: ACPI mode support for GPIO/LPSS/SCC/LPE are not supported for
now. They will be added in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like other MADT table write routines, make acpi_create_madt_lapics()
return how many bytes it has written instead of the table end addr.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds several generic ASL libraries that can be included by
other ASL files, which are:
- debug.asl: for debug output using POST I/O port and legacy serial port
- globutil.asl: for string compare routines
- statdef.asl: for _STA status values
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The comment of initializing table header revision says:
/* ACPI 1.0/2.0: 1, ACPI 3.0: 2, ACPI 4.0: 3 */
which might mislead it may increase per ACPI spec revision.
However this is not the case. It's actually a fixed number
as defined in ACPI spec, and in the laest ACPI spec 6.1,
some table header revisions are still 1. Clean these up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per ACPI spec, the FACS table address must be aligned to a 64 byte
boundary (Windows checks this, but Linux does not).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use u32 instead of unsigned long in the table write routines, as
other routines do.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rearrange the routine order a little bit, to follow the order
in which ACPI table is defined in acpi_table.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fill_header() to acpi_fill_header() for consistency.
Change its signature to remove the 'length' parameter and
make it a public API.
Also remove the unnecessary include files, and improve the
AmlCode[] comment a little bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This acpi_create_ssdt_generator() currently does nothing.
Remove this for now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reorder the ACPI tables appearance by following the order:
RSDP, RSDT, XSDT, FADT, FACS, MADT, MCFG. And adjust the
table flag defines accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Use "U-BOOT" and "U-BOOTBL" for the OEM ID and OEM table ID.
- Do not typedef acpi_header_t, instead use struct acpi_table_hader.
- Use a shorter name aslc_id and aslc-revision.
- Change MCFG base address to use 32-bit value pairs (_l and _h).
- Apply ACPI_APIC_ prefix to MADT APIC type macros and make
their names to be more readable.
- Apply __packed to struct acpi_madt_irqoverride and struct
acpi_madt_lapic_nmi tables, as they are not naturally aligned
by the compiler which leads to wrong sizeof(struct).
- Rename model to res1 as it is reserved after ACPI spec 1.0.
- Apply ACPI_ prefix to the PM profile macros and change them
to enum.
- Add ospm_flags to FACS structure which is defined since ACPI 4.0.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Remove #include <> header files.
- Remove APM_CNT register defines, which should not be here as
they are SMI related.
- Remove MP_IRQ_ defines as they are duplicates of the same ones
in asm/mpspec.h.
- Remove ACTL register defines, which should not be here as they
are chipset specific.
- Remove functional fixed hardware defines, which are not used.
- Remove dev_scope related defines, which are not used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This updates all x86 boards that currently have IRQ router in the
dts files to include ACTL register details.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default SCI is disabled after power on. ACTL is the register to
enable SCI and route it to PIC/APIC. To support both ACPI in PIC
mode and APIC mode, configure SCI to use IRQ9.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reserve IRQ9 which is to be used as SCI interrupt number
for ACPI in PIC mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the following two build warnings in function 'write_acpi_tables':
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 2 has type 'u32' [-Wformat=]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following build warning is seen in tables.c:
warning: implicit declaration of function 'memalign'
Add the missing header file to fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove asm/acpi.h which is never used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This started as 'ahci' and was renamed to 'disk' during code review. But it
seems that this is too generic. Now that we have a 'blk' uclass, we can use
that as the generic piece, and revert to ahci for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Our own ACPI implementation (when CONFIG_QEMU_ACPI_TABLE is not set)
does not build anymore after x86 has been fully converted to DM PCI.
Instead of trying to fix the build errors, given we now have the ACPI
support via QEMU's fw_cfg interface, which is a more reliable way to
generate correct ACPI tables than by ourselves, hence drop our own
ACPI implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the link script to drop this code when not needed. This is only done
for two architectures at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).
Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.
Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIe
Not supported yet is:
- I2C
- USB 3.0
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds basic support for chromebook_samus. This is the 2015 Pixel and
is based on an Intel broadwell platform.
Supported so far are:
- Serial
- SPI flash
- SDRAM init (with MRC cache)
- SATA
- Video (on the internal LCD panel)
- Keyboard
Various less-visible drivers are provided to make the above work (e.g. PCH,
power control and LPC).
The platform requires various binary blobs which are documented in the
README. The major missing feature is USB3 since the existing U-Boot support
does not work correctly with Intel XHCI controllers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sometimes it is useful to jump into U-Boot directly from coreboot or UEFI
without any 16-bit init. This can help during development by allowing U-Boot
to avoid doing all the init required by the platform.
U-Boot expects its GDT to be set up correctly by its 16-bit code. If
coreboot doesn't do this (because it hasn't run the payload setup code yet)
then this won't happen.
In this case we cannot rely on the GDT settings. U-Boot will hang or crash
if these are wrong. Provide a development-only option to set up the GDT
correctly. This is just a hack so you can jump to U-Boot from any stage of
coreboot, not just at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not needed now that the memory controller driver has the SPD data
in its own node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the existing implementation to use the new common SDRAM init code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The code to call the memory reference code is common to several Intel CPUs.
Add common code for performing this init. Intel calls this 'Pre-EFI-Init'
(PEI), where EFI stands for Extensible Firmware Interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
