These days many Allwinner SoCs use clock_sun6i.c, although out of them
only the (original sun6i) A31 has a second MBUS clock register.
Also the requirement for setting up the PRCM PLL_CTLR1 register to provide
the proper voltage seems to be a property of older SoCs only as well.
Restrict the MBUS initialization to this SoC only to avoid writing bogus
values to (undefined) registers in other chips.
I can only verify that the PLL voltage setup is not needed for H3 and
A64, so for now we only spare those two SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
For writing Linux or rootfs on to NAND, the best suitable way
is to use MMC commands since MMC driver by default enabled by
mx6_common.h, hence enabled MMC commands in nand defconfigs.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Some OS (all BSD and probably others) do not have python in /usr/bin
but in another directory.
It is a common usage to use /usr/bin/env python as shebang for python
scripts so use this for binman.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
The display is done in the device tree now, and there is no need
to pass 'display' kernel parameter any longer.
Signed-off-by: Adam Ford <aford173@gmail.com>
First, update the code snippet referenced in the README file. And
since there are only two boards that override flash_cmd_reset(),
might as well show them both.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the
MX6DQP it is '3'.
This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of
132 MHz.
Instead of relying on the POR values for the CSMR1 register, make sure to
manually configure the clk_eim_slow_sel field as '00' so that EIM clock is
derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM
clock can be AXI clock divided by 2.
This way a consistent EIM clock frequency is configured for all the mx6
variants.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Enable USB gadget ethernet by default to have networking capabilities.
Tested using DHCP and TFTP to transfer kernel, DT, ramdisk.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
'fdtfile' is the preferred name for the variable that contains the
device tree blob according to the README file.
It also makes it consistent with other i.MX boards that use config_distro,
so change it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.
Cc: sbabic@denx.de
v2-Changes:
- No usage of MKIMAGEOUTPUT_$(@F) macro.
- Predefine default value /dev/null in every involved Makefile.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
When we want to use Secure Boot with HAB from SPL over U-Boot.img,
we need to append the IVT to the image and leave space for the CSF.
Images generated as firmware_ivt can directly be signed using the
Freescale code signing tool. For creation of a CSF, mkimage outputs
the correct HAB Blocks for the image.
The changes to the usual firmware image class are quite small,
that is why I implemented that directly into the default_image.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
These files are blowing up the SPL and should not be required
there as the SPL delivers no command console. Because building fails
for mx27 and mx31 machines with SPL build, we remove the linker flag
for them from the Makefile. Nothing is built for them to be linked
in that directory.
Cc: sbabic@denx.de
v2 Changes:
- Remove mx27 and mx31 from Makefile during SPL build as nothing is built for
them in that directory. And removing the commands with the libs-y directive
lead to linker failures. e.g. "armv5te-ld.bfd: cannot find arch/arm/imx-common/built-in.o: No such file or directory)"
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Commit c94981efa2 ("udoo_neo: Remove USDHC3 support") removed
the SDHC3 support, but missed to remove the entry from the usdhc_cfg
structure, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In commit 7044c6bb6 (net: cosmetic: Clean up DHCP variables and functions)
BootpCopyNetParams() was renamed to store_net_params(). Update the reference in
comment.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
genext2fs creates revision level 0 filesystems, which are not readable
by u-boot due to the initialized group descriptor size field.
f798b1dda1
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: FrostyBytes@protonmail.com
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
With capacities getting bigger, we can see see messages with negative
numbers like "Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)".
Here the printed LBA is -387938128 when it should have been 3907029168.
To fix this, use the right format when displaying the unsigned integers.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
This patch is fixing missing fclose() calls
in error patch introduced by:
"tools: mkimage: Use fstat instead of stat to avoid malicious hacks"
(sha1: ebe0f53f48)
Reported-by: Coverity (CID: 155064, 155065)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These options are now described in the Kconfig help. We do not want
to maintain duplicated documentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>