Command calls update_tftp() analogous to automatic update described
in doc/README.update.
Usage:
fitupd [addr]
- run update from FIT image at addr
or from tftp 'updatefile'
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Current update_tftp() flow:
1.) fetch "updatefile" from defined TFTP server
2.) check if FIT format
3.) flash contained images
Add an address parameter to update_tftp(). If this address is non-zero,
skip the TFTP transfer and use the image at this address.
Also extend update_tftp() to return success/fail.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
The current arch/driver specific UART posts basically boil down to setting
the UART to loop back mode, then reading and writing data. If we ignore
the loop back part, the rest can be built upon the existing common serial
API. So let's do just that.
First add a call back for serial drivers to implement loop back control.
Then write a post test that walks all of the serial drivers, puts them
into loop back mode, and verifies that reading/writing at all the diff
baud rates is OK.
If a serial driver doesn't support loop back mode (either it can't or
it hasn't done so yet), then skip it. This should allow for people to
easily migrate to the new post test with existing serial drivers.
I haven't touched the few already existing uart post tests as I don't
the hardware or knowledge of converting them over. So I've marked the
new test as weak which will allow the existing tests to override the
default until they are converted.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The serial_register function never fails (always return 0), so change it
to a void function to avoid wasting overhead on it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
For people who want to manually extract the embedded environment so that
it can be manually packed into the final u-boot image, add a config opt
to force building of the envcrc tool.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Fix: if using md5 command watchdog timed out
* change function call md5(..) to the watchdog-safe variant
md5_wd(..) to support watchdog reset
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
* Fix: if using sha1 command watchdog timed out
* change function call sha1_csum(..) to the watchdog-safe variant
sha1_csum_wd(..) to support watchdog reset
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
It might be desirable to have the ability to flush icache/dcache
within u-boot, this patch gives each arch the ability to provide
a flush_dcache/flush_icache function to let u-boot flush caches
from the prompt
Signed-off-by: Matthew McClintock <msm@freescale.com>
Print a message if we do not have the ability to uncompress a gzip
image. Before, u-boot would just assume the routines were available
Signed-off-by: Matthew McClintock <msm@freescale.com>
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
In miiphy_register() the new device's name was initialised by passing a
string parameter as the format string to sprintf(). As this would cause
problems if it ever contained a '%' symbol, switch to using strncpy()
instead.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Andy Fleming <afleming@freescale.com>
* Fix: if using crc32 command watchdog timed out
* change function call crc32(..) to the watchdog-safe variant
crc_32_wd(..) to support watchdog reset
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Remove an unneeded prototype declaration from the top of main.c,
and use plain inline instead of __inline__ to please checkpatch.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Rather than having a bunch of random commands handle autostart behavior,
unify the logic in a single place. This also fixes building of these
different commands when bootm is disabled.
Acked-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mmc:
mmc: rescan fails on empty slot
AT91:mmc:fix multiple read/write error
mmc: Access mode validation for eMMC cards > 2 GiB
mmc: sh_mmcif: add support for Renesas MMCIF
mmc: fix the condition for MMC version 4
MMC: add marvell sdhci driver
MMC: add sdhci generic framework
MMC: add erase function to both mmc and sd
MMC: unify mmc read and write operation
mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony
mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Add a new "fdt_high" enviroment variable. This can be used to control (or prevent) the
relocation of the flattened device tree on boot. It can be used to prevent relocation
of the fdt into highmem. The variable behaves similarly to the existing "initrd_high"
variable.
Signed-off-by: David A. Long <dave.long@linaro.org>
Fail in 'mmc rescan' if mmc_init() returns error
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
mmc read and write command has so many in common, unfiy those two to
force consistency across the those two.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Andy Fleming <afleming@freescale.com>
The ePAPR specification says that phandle properties should be called
"phandle", and not "linux,phandle". To facilitate the migration from
"linux,phandle" to "phandle", introduce function fdt_create_phandle(),
which creates a phandle in a given node. For now, we create both the
"phandle" and "linux,phandle" properties. A later version of this
function will remove support for "linux,phandle".
Signed-off-by: Timur Tabi <timur@freescale.com>
Introduce two functions, fdt_verify_alias_address() and
fdt_get_base_address(), which can be used to verify the physical address
of a device in a device tree.
fdt_get_base_address() returns the base address of an SOC or PCI node.
fdt_verify_alias_address() prints a message if the address of a node
specified by an alias does not match the given physical address.
Signed-off-by: Timur Tabi <timur@freescale.com>
This brings CONFIG_SERIAL_MULTI support to the Blackfin on-chip UARTs.
Ends up adding only ~512bytes per additional UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
Add another nand write. variant, trimffs. This command will request of
nand_write_skip_bad() that all trailing all-0xff pages will be
dropped from eraseblocks when they are written to flash as-per the
reccommended behaviour of the UBI FAQ [1].
The function that implements this timming is the drop_ffs() function
by Artem Bityutskiy, ported from the mtd-utils tree.
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
CC: Detlev Zundel <dzu@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
All data in dtb is big endian. Some ARM devices are little-endian.
In print_data(), it displays data with big-endian format. For ARM device,
data should be converted to little-endian first.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Gerald Van Baren <vanbaren@cideas.com>
When we use the ntpserverip environment variable argv[1] may not be set.
Printing the error message using the NetNtpServerIP variable ensures the
correct output in both cases.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Since commit 30486322 (nand erase: .spread, .part, .chip subcommands)
the arguments off and size are no longer optional.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit 30486322 (nand erase: .spread, .part, .chip subcommands)
added a new field to struct nand_erase_options, but forgot to
update common/env_nand.c.
Depending on the stack state and bad block distribution, saveenv()
can thus erase more than CONFIG_ENV_RANGE bytes which may corrupt
the following NAND sectors/partitions.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)
As bootloader may need to read out or reflashing images on those
different partitions, it is better to enable the partition switch with
console command support.
Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
When calling getenv_f() with a too small buffer, it would print an
error message like this:
env_buf too small [32]
This is not really helpful as it does not give any indication which of
the calls might have failed. Change this into:
env_buf [32 bytes] too small for value of "hwconfig"
so we know at least which variable caused the overflow; this usually
allows to quickly find the related code as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
do not define own flash_info variable, instead use
the flash_info variable defined in your flash driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The changes introduced by commit 0abddf8 ``cmd_ide: enhance new
feature "CONFIG_IDE_AHB"'' caused compiler warnings like
cmd_ide.c: In function 'ide_init':
cmd_ide.c:716: warning: assignment from incompatible pointer type
Constify the respective function arguments to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cmd_mdio.c: In function 'mdio_read_ranges':
cmd_mdio.c:97: warning: comparison is always false due to limited range of data type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Fix warning introduced while recent PHY Lib changes:
miiphyutil.c: In function 'miiphy_read':
miiphyutil.c:304: warning: comparison is always false due to limited range of data type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
As Andy Fleming suggested, we can call mmc_init() in mmc_spi command.
So that we don't need to run mmcinfo command next.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
To make sure that the mux can be configured a deblocking sequence
is done before the mux configuration. After the mux switch the new leaf
of, the i2c tree must be again deblocked.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching. grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.
the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:
Example 1: summarize ethernet configuration:
=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>
Example 2: detect unused env vars:
=> grepenv etact
etact=FM1@DTSEC2
=>
Example 3: reveal hardcoded variables; e.g., for fdtaddr:
=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>
This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This patch fixes problems in the handling of redundant environment in env_sf.c
The major problem are double calls of free() on the allocated buffers,
which damages the internal data of malloc and crashes on next call.
In addition, the selection of the active environment had errors and compiler
warnings, which are corrected by this patch.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
This patch allows any board implementing the coloured LED API
to control the LEDs from the console.
led [green | yellow | red | all ] [ on | off ]
or
led [ 1 | 2 | 3 | all ] [ on | off ]
Adds configuration item CONFIG_CMD_LED enabling the command.
Partially based on patch from Ulf Samuelsson:
http://www.mail-archive.com/u-boot@lists.denx.de/msg09593.html.
Updated based on feedback:
http://www.mail-archive.com/u-boot@lists.denx.de/msg41847.htmlhttps://groups.google.com/d/topic/beagleboard/8Wf1HiK_QBo/discussion
* Fixed a handful of style issues.
* Significantly reduced the number of #ifdefs and redundant code
* Converted redundant code into loops test against a structure
* Made use of cmd_usage()
* Introduced a str_onoff() function, but haven't yet put it in common
* Eliminated trailing newline
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
If a regions is reserved in the fdt, then it should not be used. Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The initrd_end variable contains the address immediately *after* the
initrd blob, not the last address containing data. This patch fixes
an inadvertent off-by-one when setting up the initrd reserved map.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low(). Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3. This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Mostly putting a space between function name and "(", and
doing return (foo)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
When fdt_fixup_memory_banks is called with 2-cell address and size
fields in the device-tree (IE: 64-bit address and size), then it will
overflow its on-stack "tmp" buffer.
This fixes the buffer size and adds a comment explaining how many bytes
need to be allocated per record.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Jerry Van Baren <vanbaren@cideas.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The Blackfin gpio command isn't terribly Blackfin-specific. So generalize
the few pieces into two new optional helpers:
name_to_gpio() - turn a string name into a GPIO #
gpio_status() - display current pin bindings (think /proc/gpio)
Once these pieces are pulled out, we can relocate the cmd_gpio.c into the
common directory.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There's no real need to keep these functions in the cmd_mem file since
they do not use any of the common global mem variables. So split them
out into their own dedicated cmd files.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes following warning message:
---8<---
cmd_bdinfo.c:458: warning: initialization from incompatible pointer type
--->8---
There was a prototype change in 54841ab50c for
argv[] pointer type to const. This change was not made for AVR32 cause this
code came in later by a merge.
Signed-off-by: Andreas Biemann <biessmann@corscience.de>
This patch fixes warnings in MAKEALL for avr32:
---8<---
cmd_nvedit.c: In function 'do_env_export':
cmd_nvedit.c:663: warning: format '%zX' expects type 'size_t', but argument 3 has type 'ssize_t'
--->8---
Signed-off-by: Andreas Biemann <biessmann@corscience.de>
This patch adds [+]len handler for the erase command that will
automatically round up the requested erase length to the flash's
sector_size.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For uImage always has a 64 bytes header, we couldn't expect to do
the xip from the header but should xip from the image start.
The latter logic in that section is also move the image from image_start
to the load address, so sync this logic to the xip operation.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
On some boards the environment may not be located at a fixed address in
the MMC/SDHC card. This allows those boards to implement their own
means to report what address the environment is located at.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The reset request in usb_stor_get_info is causing issues with some usb
sticks. Some of these sticks vendor_id/product_id have been hardcoded to
not reset but better is to remove the reset altogether. It is not needed.
Signed-off-by: Erik Hansen <erik@makarta.com>
Some ubi commands returned negative error codes, resulting in
the following error message on the prompt:
"exit not allowed from main input shell."
Negative error codes are not allowed.
This patch now changes the UBI code to return positive error codes.
Additionally "better" error codes are used, for example "ENOMEM" when
no memory is available for the UBI volume creation any more.
Also the output of some commands is enhanced:
Before:
=> ubi read 100000 testvol 100000
Volume testvol found at volume id 0
read 1048576 bytes from volume 0 to 100000(buf address)
=> ubi write 100000 testvol 1000
Volume testvol found at volume id 0
After:
=> ubi read 100000 testvol 100000
Read 1048576 bytes from volume testvol to 00100000
=> ubi write 100000 testvol 1000
4096 bytes written to volume testvol
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
These variables are only used in case CONFIG_SYS_NO_FLASH is NOT set:
struct mtd_device *dev;
struct part_info *part;
u8 dev_type, dev_num, pnum;
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
The unzip command did not provide a way for the caller to get any
information about the uncompressed size. To make it better usable in
scripts, we now store the uncompressed size in the `filesize'
variable, like we do when for example loading a file over the network
or when reading it from a file system. Following that analogy, it is
only consequent to also print the size.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The implementation of the string compare function of the "itest"
command was weird, as only the length of the shortest argument was
included in the compare, with the result that something like
"itest.s abd == abddef" would return TRUE. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
While debugging some USB stuff, I've first missed that there are actually
two defines necessary to get usefull output. The one needed to get debug output
for the communication with HUBs was burried somewhere deep inside the code.
Change that so that a #define DEBUG is enough while still leaving the possibility
to reduce unwanted debug output.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
I currently don't know if the error could have other consequences
than a wrong output when turning debug on.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
commit 8bde63eb3f ([MIPS] Rename Alchemy
processor configs into CONFIG_SOC_*) forgot to pick up this one.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
When redundand environments are used the serial needs
to get increased, otherwise the old one will still be used.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
After years of unsuccessful research I've finally shamelessly stolen other
peoples intellectual properties to present the all-new and world-changing
updated version command:
-
U-Boot>> version
U-Boot 2010.12-00014-g7435056-dirty (Jan 18 2011 - 23:19:38)
MyBoard
gcc (GCC) 0.42 (Distro foobar)
GNU ld (GNU Binutils) 0.314159265
-
May the toolchain bugs rest in peace.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
CONFIG_SPLASH_SCREEN_ALIGN makes uboot support display
offset for splashimage. The framebuffer writing address
should be calculated according to different kinds of
framebuffer pixel format, i.e., bits per pixel value.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
There are several users of the hwconfig APIs (8xxx DDR) before we have
the environment properly setup. This causes issues because of the
numerous ways the environment might be accessed because of the
non-volatile memory it might be stored in. Additionally the access
might be so early that memory isn't even properly setup for us.
Towards resolving these issues we provide versions of all the hwconfig
APIs that can be passed in a buffer to parse and leave it to the caller
to determine how to allocate and populate the buffer.
We use the _f naming convention for these new APIs even though they are
perfectly useable after relocation and the environment being ready.
We also now warn if the non-f APIs are called before the environment is
ready to allow users to address the issues.
Finally, we convert the 8xxx DDR code to utilize the new APIs to
hopefully address the issue once and for all. We have the 8xxx DDR code
create a buffer on the stack and populate it via getenv_f().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Documented is CONFIG_CMD_SHA1, through confusion in the source
CONFIG_CMD_SHA1 and CONFIG_CMD_SHA1SUM has to be used to enable
sha1sum.
Fix both, the documentation and the source, so that only
CONFIG_CMD_SHA1SUM is needed to enable the command sha1sum.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
When a flash partition was positioned at the very top of a 32-bit memory
map (eg located at 0xf8000000 with a size of 0x8000000)
get_part_sector_size_nor() would incorrectly calculate the partition's
ending address to 0x0 due to overflow. When the overflow occurred
get_part_sector_size_nor() would falsely return a sector size of 0.
A sector size of 0 results in subsequent jffs2 operations failing.
To workaround the overflow subtract 1 from calculated address of
the partition endpoint.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch add addition suffix to nand write to give the uboot
the power to directly burn the yaffs image to nand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
This reverts commit 5a442c0add.
This commit changed the behaviour of getenv_yesno() (both the default
behaviour and the documented behaviour for abbreviated arguments)
which resulted in problems in several areas.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than keep the load_addr definition with the bootm code (which
just happens to use this), move it to the common env code. This way
we can disable bootm support completely while retaining load_addr
usage with many other commands.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have config_defaults.h which are random configuration settings that
everyone gets by default. We also have config_cmd_default.h which is a
recommended list of defaults but boards have to opt into. Now we have
config_cmd_defaults.h which is a list of defaults that everyone gets
and has to actively opt out of.
For now, we populate it with the bootm command which previously was
unable to be disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 722b061 "autocomplete: remove runtime handler install" caused
some boards (like NETTA2_V2) to break with errors like these:
cmd_net.c:296: error: expected expression before ',' token
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Yaffs image require to use the oob to store some info, so when we
burn the yaffs image, we need to also write the image's oob part
into flash.
This patch add addition suffix to onenand write to give the uboot
the power to directly burn the yaffs image to onenand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The non-reentrant versions of the hashtable functions operate on a single
shared hashtable. So if two different people try using these funcs for
two different purposes, they'll cause problems for the other.
Avoid this by converting all existing hashtable consumers over to the
reentrant versions and then punting the non-reentrant ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The handling of env_hwconfig, board_hwconfig, and cpu_hwconfig got
broken when we removed the boards defining dummy board_hwconfig
& cpu_hwconfig values.
We fix this by handling the various strings in priority order. If
hwconfig_parse returns NULL for a given string we check the next one
in order (env_hwconfig, board_hwconfig, followed by cpu_hwconfig).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Seems original implementation forget to set the pointer to point
to the oobbuf, so when we want to see oob buf, we see nothing...
Fix it by get pointer as the oobbuf set.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The nand-read function returns an error code if correctable errors have occurred.
This is not desirable, since the errors have been corrected!
This patch switches to the nand_read_skip_bad function which does not
return an error code if the errors are correctable.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Automatically unmount UBIFS partition when user changes the UBI device.
Otherwise the following UBIFS commands will crash.
Signed-off-by: Stefan Roese <sr@denx.de>
Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a
default value they will get put into the BSS if they aren't defined
elsewhere. This is problematic as we try to utilize hwconfig before
we've relocated and thus BSS isn't setup.
Instead of giving dummy values in the board files that utilize this
feature, we can just initialize the variables to an empty string and
thus move them out of the BSS if they aren't defined elsewhere.
Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated
with string pointers vs arrays.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than add runtime overhead of installing completion handlers, do it
statically at build time. This requires a new build time helper macro to
declare a command and the completion handler at the same time. Then we
convert the env related funcs over to this.
This gives an opportunity to also unify the U_BOOT_CMD macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness). Unify them
all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No need for these structures to be writable or global.
While we're here, also drop local versions of the ARRAY_SIZE macro.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix compiler warning
fdt_support.c: In function 'of_bus_default_count_cells':
fdt_support.c:957: warning: passing argument 1 of '__swab32p' discards qualifiers from pointer target type
fdt_support.c:965: warning: passing argument 1 of '__swab32p' discards qualifiers from pointer target type
be32_to_cpup() expects an 'u32 *' while prop is 'const u32 *'.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Use the return value of cmd_usage instead of ignoring this
and returning a 1.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Guard strchr/strlen from being called with NULL pointer.
This line is crashing when command "env" is called without subcommand.
The cmd is NULL in this case because the calling function "do_env"
decremented the argc without checking if there are still arguments available.
Signed-off-by: Thomas Weber <weber@corscience.de>
Some boards use an embedded environment, where env_embedded.o has to
be linked at a special position in the U-Boot image; to make this
possible, we do not include it into libcommon.o for such boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Since we set #define MORECORE_CLEARS 1, the code assumes 'sbrk' always
returns zero'd out memory. However since its possible that free()
returns memory back to sbrk() via malloc_trim we could possible get
non-zero'd memory from sbrk(). This is a problem for when code might
call calloc() and expect the memory to have been zero'd out.
There are two possible solutions to this problem.
1. change #define MORECORE_CLEARS 0
2. memset to zero memory returned to sbrk.
We go with the second since the sbrk being called to free up memory
should be pretty rare.
The following code problems an example test to show the issue. This
test code was inserted right after the call to mem_malloc_init().
...
u8 *p2;
int i;
printf("MALLOC TEST\n");
p1 = malloc(135176);
printf("P1 = %p\n", p1);
memset(p1, 0xab, 135176);
free(p1);
p2 = calloc(4097, 1);
printf("P2 = %p %p\n", p2, p2 + 4097);
for (i = 0; i < 4097; i++) {
if (p2[i] != 0)
printf("miscompare at byte %d got %x\n", i, p2[i]);
free(p2);
printf("END MALLOC TEST\n\n");
...
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This change does the following:
- Removes the printing of the PCI interrupt line value. This is
normally set to 0 by U-Boot on bootup and is rarely used during
everyday operation.
- Prints out the PCI function number of a device. Previously a device
with multiple functions would be printed identically 2 times, which is
generally confusing. For example, on an Intel 2 port gigabit Ethernet
card the following was displayed:
...
04 01 8086 1010 0200 00
04 01 8086 1010 0200 00
...
- Prints a text description of each device's PCI class instead of the
raw PCI class code. The textual description makes it much easier to
determine what devices are installed on a PCI bus.
- Changes the general formatting of the PCI device output.
Previous output:
PCIE1: connected as Root Complex
04 01 8086 1010 0200 00
04 01 8086 1010 0200 00
03 00 10b5 8112 0604 00
02 01 10b5 8518 0604 00
02 02 10b5 8518 0604 00
08 00 1957 0040 0b20 00
07 00 10b5 8518 0604 00
09 00 10b5 8112 0604 00
07 01 10b5 8518 0604 00
07 02 10b5 8518 0604 00
06 00 10b5 8518 0604 00
02 03 10b5 8518 0604 00
01 00 10b5 8518 0604 00
PCIE1: Bus 00 - 0b
PCIE2: connected as Root Complex
0d 00 1957 0040 0b20 00
PCIE2: Bus 0c - 0d
Updated output:
PCIE1: connected as Root Complex
04:01.0 - 8086:1010 - Network controller
04:01.1 - 8086:1010 - Network controller
03:00.0 - 10b5:8112 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
08:00.0 - 1957:0040 - Processor
07:00.0 - 10b5:8518 - Bridge device
09:00.0 - 10b5:8112 - Bridge device
07:01.0 - 10b5:8518 - Bridge device
07:02.0 - 10b5:8518 - Bridge device
06:00.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
01:00.0 - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 0b
PCIE2: connected as Root Complex
0d:00.0 - 1957:0040 - Processor
PCIE2: Bus 0c - 0d
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
hexport would complain implicit declaration, if we don't add the
include file.
env_mmc.c: In function 'saveenv':
env_mmc.c:109: warning: implicit declaration of function 'hexport'
Signed-off-by: Lei Wen <leiwen@marvell.com>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Running the onenand command without arguments does nothing, with this
patch shows the command usage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Functions to store/retrieve the environment from a SPI flash was not updated
to the new environment code. The non-redundant case was
not working correctly, reporting ""Environment SPI flash not initialized"
and the code was not compiled clean in the redundant case.
The patch fixes these issue and makes the code more coherent
with other environment storage (nand, flash).
Signed-off-by: Stefano Babic <sbabic@denx.de>
This commit causes build errors like this:
cmd_net.c:301:1: error: macro "U_BOOT_CMD" requires 6 arguments, but only 5 given
cmd_net.c:298: warning: data definition has no type or storage class
cmd_net.c:298: warning: type defaults to 'int' in declaration of 'U_BOOT_CMD'
This reverts commit 8f4cb77ef7.
Building for boards that have CONFIG_CMD_CDP enabled fail with:
cmd_net.c:301: error: expected expression before ',' token
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
We also have to relocate the onenand command table manually, otherwise
onenand command don't work.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Since we use hwconfig in cases before relocation (like getting DDR
params on FSL PPC systems), we can have strings that exceed the early
small (32 byte) buffer size that getenv will handle.
So we explicitly allocate our own buffer on the stack and use if to
handle getting the hwconfig env string. We currently utilize a string
length of 128 bytes.
This allows us to get rid of boot messages like:
env_buf too small [32]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With debug the follow is printed:
=> saveenv
Saving Environment to Flash...
Data to save 0x18000
Data (start 0xfff48000, len 0x18000) saved at 0x7fe63f20
Protect off FFF40000 ... FFF5FFFF
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... Restoring the rest of data to 0xfff48000 len 0x18000
done
Protected 1 sectors
=>
Without debug:
=> saveenv
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
=>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add a new 'pci enum' command which re-enumerates the PCI buses. This
command is enabled via the CONFIG_CMD_PCI_ENUM define and can be useful
in boards with FPGAs connected via PCI/PCIe, boards that support PCI
hot-plugging, or during PCI debug.
Also enable the 'pci enum' command for X-ES's Freescale-based boards.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
The device tree (fdt) must always exist in within the bootmap (usually the
first 16MB of RAM). If it doesn't, then boot_relocate_fdt() will allocate
an LMB region in the bootmap and copy the fdt into that region. It will
also increase the size of the fdt.
If the fdt is already in the bootmap, then previously the memory was just
reserved. There was no contingency if the reservation failed, however.
By always allocating an lmb region and copying/resizing the fdt into that
region, the code is simplified and the memory region is always allocated
properly.
Also change the types of some variables to avoid some typecasts.
Signed-off-by: Timur Tabi <timur@freescale.com>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit a6bd9e8 "FDT: Add fixup support for multiple banks of memory"
removed code but forgot to remove the variables used by it, resulting
in warnings:
fdt_support.c: In function 'fdt_fixup_memory_banks':
fdt_support.c:399: warning: unused variable 'sizecell'
fdt_support.c:399: warning: unused variable 'addrcell'
Remove the declarations, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The usage and help for the fpga command is wrong and incomplete,
and the parameters are not checked before to be passed to the
underlying subfunction.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.
Use CONFIG_SYS_BOOT_<FEATURE> defines instead.
CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD
Define these as appropriate in arch/include/asm/config.h files.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
All arches except nios2 and microblaze call boot_get_fdt
from bootm_start in common/cmd_bootm.c.
Having nios2 and microblaze do so as well removes code from
their respective do_bootm_linux routines and allows removal of
a nasty ifdef from bootm_start.
In the case where boot_get_fdt returns an error bootm_start
returns and the platform specific do_bootm_linux routines
will never get called.
Also only check argv[3] for an fdt addr if argc > 3 first.
This is already the case for nios2.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Scott McNutt <smcnutt@psyent.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Add fdt_fixup_memory_banks and reimplement fdt_fixup_memory
using it. Tested on OMAP3 beagle board with two banks of
memory.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Jerry Van Baren <vanbaren@cideas.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
fdt_totalsize returns size in cpu endian so don't call be32_to_cpu
on the result. This was harmless on big endian platforms but not
on little endian ARMs.
Signed-off-by: John Rigby <john.rigby@linaro.org>
boot_relocate_fdt is called on platforms with CONFIG_SYS_BOOTMAPSZ
defined to relocate the device tree blob to be inside the
boot map area between bootmap_base and bootmap_base+CONFIG_SYS_BOOTMAPSZ.
For the case where the blob needs to be relocated, space is
allocated inside the bootmap by calling lmb_alloc_base with
size passed in plus some padding:
of_len = *of_size + CONFIG_SYS_FDT_PAD;
For the case where the blob is already inside the bounds of the boot map
area, lmb_reserve is called to reserve the the space where the blob is
already residing. The calculation for this case is currently:
of_len = (CONFIG_SYS_BOOTMAPSZ + bootmap_base) - (ulong)fdt_blob;
This is wrong because it reserves all the space in the boot map area
from the blob to the end ignoring completely the actual size. The
worst case is where the blob is at the beginning and the entire boot map
area get reserved. Fix this by changing the length calculation to this:
of_len = *of_size + CONFIG_SYS_FDT_PAD;
This bug has likely never manifested itself because bootm has never
been called with the fdt blob already in the bootmap area. In my
testing on an OMAP3 beagle board I initially worked around the bug
by simply moving the initial location of the fdt blob. I have tested
with the new calculation with the fdt blob both inside and outside
the boot map area.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix these warnings:
dlmalloc.c: In function 'free':
dlmalloc.c:2507: warning: dereferencing pointer '({anonymous})' does break strict-aliasing rules
dlmalloc.c:2507: warning: dereferencing pointer '({anonymous})' does break strict-aliasing rules
dlmalloc.c:2507: warning: dereferencing pointer '({anonymous})' does break strict-aliasing rules
Some page(http://blog.worldofcoding.com/2010/02/solving-gcc-44-strict-aliasing-problems.html)
suggests adding __attribute__((__may_alias__)). Doing so makes the warnings go away.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Commit ea533c260a changed
arg_off_size to take a pointer to a device index, rather than
to the device itself. When updating callers, the nand unlock
code was missed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The env change its implementation after this log, while env mmc
didn't change it immediately, which cause issue. Follow to the
new style to fix it.
commit ea882baf9c
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Jun 20 23:33:59 2010 +0200
New implementation for internal handling of environment variables.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The crash was occuring in env_relocate because it was being called prior
to mmc_initialize. This patch moves the MMC initialization earlier in
the init process.
This patch also cleans up the env_relocate_spec code in env_mmc.c
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch changes `usb_stor_scan' to scan all the LUNs of each mass
storage device. It also fixes the various commands to correctly set
the LUN field.
Notably, it allows each LUN of GuruPlug's microSD card reader to be
accessed.
Signed-off-by: Ludovic Courtès <ludo@gnu.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch does 2 things:
- Fix the argument number assigned to the vdw (VME data width) value.
Previously, a nonexistent 7th arument was read as the vdw variable.
- Reduce the size of the argument array for the tsi148 command from
8 to 7. The tsi148 command itself is argument index 0, and the
maximum number arguments passed to the command is 6, making a total
of 7 for the array.
Signed-off-by: Brent Darley <bdarley@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
On some boards with a very short watchdog timeout, the "cp" and
"cmp" commands may reset the board. This patch adds some
watchdog resets inside the loops. Otherwise for example the lwmon5
board will reset while doing something like this:
=> cp.b fc000000 1000000 100000
Signed-off-by: Stefan Roese <sr@denx.de>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
When use the CONFIG_ENV_IS_NOWHERE, I met such issue:
DRAM: 256 MiB
Using default environment
*** Warning - bad CRC, using default environment
Signed-off-by: Lei Wen <leiwen@marvell.com>
Boards can pass display timing info for drivers using EDID
block. Provide common function to add board specific EDID
data to the device tree. Subsequent patch makes use of this
functionality.
Detailed timing descriptor data from EDID is used for
programming the display controller. This is currently
implemented on the Linux side by the fsl-diu-fb frame
buffer driver and it is documented there in
Documentation/powerpc/dts-bindings/fsl/diu.txt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
The include <jffs2/jffs2.h> is still necessary though.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Stefan Roese <sr@denx.de>
Most people don't use the 'rarpboot' command, so only enable it when
CONFIG_CMD_RARP is defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Consolidate some code in mtd_get_len_incl_bad(), and fix a condition
where a valid partition could be reported as truncated if it has a
good block at the end of the device (unlikely, since the BBT is usually
there).
Fix mid-block declarations in net_part_size().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
This patch adds a new 'mtdparts add' variant: add.spread. This command variant
adds a new partition to the mtdparts variable but also increases the partitions
size by skipping bad blocks and aggregating any additional bad blocks found at
the end of the partition.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
This patch introduces the 'spread' sub-command of the mtdparts command.
This command will modify the existing mtdparts variable by increasing
the size of the partitions such that 1) each partition's net size is at
least as large as the size specified in the mtdparts variable and 2)
each partition starts on a good block.
The new subcommand is implemented by iterating over the mtd device
partitions and collecting a bad blocks count in each -- including any
trailing bad blocks -- and then modifying that partitions's part_info
structure and checking if the modification affects the next partition.
This patch is based on a port of the 'dynnamic partitions' feature by
Harald Welte <laforge@gnumonks.org>; ported from commit
e05835df019027391f58f9d8ce5e1257d6924798 of
git://git.openmoko.org/u-boot.git. Whereas Harald's feature used a
compile-time array to specify partitions, the feature introduced by
this patch uses the mtdparts environment variable.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
This patch adds an additional column to the output of list_partitions. The
additional column will contain the net size and a '(!)' beside it if the net
size is not equal to the partition size.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
The get_mtd_device_nm function is called in a couple places and the
string that is passed to it is not really used after the calls.
This patch regroups the calls to this function into a new function,
get_mtd_info.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Stefan Roese <sr@denx.de>
CC: Wolfgang Denk <wd@denx.de>
The dump command is made to increment its address on repeat,
as md does. Other commands do not make sense to issue repeatedly,
and can be irritating when it happens accidentally, so don't.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
- If the current device is overridden by a named partition,
- update the caller's pointer/index, rather than copy over the
nand_info struct, and
- be sure to call board_nand_select_device even when the device
is overridden by a named partition.
- Support 64-bit offsets/sizes in a few more places.
- Refactor arg_off_size for added readability and flexibility,
and some added checks such as partition size.
- Remove redundant check for bad subcommands -- if there's no match
it'll print usage when it gets to the end anyway.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
and clean up error messages and help,
removed pointless debug() call.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current ELF loading function does a lot of work above and beyond a
simple "loading". It ignores the real load addresses and loads things
into their virtual (runtime) address. This is undesirable when we just
want it to load an ELF and let the ELF do the actual C runtime init.
So add a command line option to let people choose to load via either the
program or section headers. I'd prefer to have program header loading
be the default, but this would break historical behavior, so I'll leave
section header loading as the norm.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes the compilation problem introduced with commit
e3c78c9b [ppc4xx: Remove now unused CONFIG_UART1_CONSOLE]:
-> ./MAKEALL TB5200
Configuring for TB5200 board...
serial.c: In function '__default_serial_console':
serial.c:94: warning: no return statement in function returning non-void
I accidentally removed an "#else" line. This patch adds it back.
Signed-off-by: Stefan Roese <sr@denx.de>
commit ea882baf9c introduces
a command_sub_table for the "env" command. On arm, avr32, m68k,
mips and sparc architectures, relocation needs manual fixups,
so add these fixups for this sub command table too.
Tested on arm/qong board.
mips board (Ben NanoNote) from Xiangfu Liu
arm/AT91 board from Reinhard Meyer
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
cc: Xiangfu Liu <xiangfu@openmobilefree.net>
cc: Reinhard Meyer <u-boot@emk-elektronik.de>
cc: sshtylyov@mvista.com
Previously the function was set_default_env(void), it is now
set_default_env(const char *s). This patch adds the required
parameter. This fixes a broken build on OMAP4430 SDP.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
This patch fixes a bug in fdt_fixup_nor_flash_node() when the reg
property has multiple reg tuples, like:
reg = <0 0x00000000 0x04000000
0 0x04000000 0x04000000>;
In this case this function did not update the reg property correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
The OTP code does a little shuffling of arguments that aren't really
necessary, so use a local variable instead to fix build errors now
that the args[] parameter is const.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now
removed since the move from the 4xx UART driver to the common NS16550
UART driver. Let's remove all references to this define now.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.
The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.
All PPC4xx board config headers are changed to use this common NS16550
driver now.
Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the behaviour of the fdt_fixup_nor_flash_node()
function. Now it doesn't patch the size of the "reg" property with the
chip-select size, but with the size returned from the new function
flash_get_bank_size(). This function will return per weak default the
flash size of the bank (bank = chip-select numer) detected by the flash
driver. If this does not fit your needs, this function may be overridden
by a board specific one.
For this the parameters needed to be changed. So I intentionally squashed
the PPC4xx stuff using this routine into this patch. Otherwise it would
not be git-bisectable anymore.
The board specific function for the AMCC/APM Ebony eval board is now
included in this patch version.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Detlev Zundel <dzu@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Cc: Wolfgang Denk <wd@denx.de>
Rather than using a custom "Usage:", use the common cmd_usage() function,
and tail into it now that it returns 1 for us.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the defines are moved to header files we don't need this
conditional compilation any more. Remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch simplifies the use of CONFIG_SYS_MAX_FLASH_BANKS_DETECT. By
moving these optional variables and defines into the common code, board
specific code is minimized. Currently only the following board use
this feature:
APC405, IDS8247, TQM834x
And IDS8247 doesn't seem to really need this feature, since its not
updating the bank number variable at all. So this patch removes the
definition of CONFIG_SYS_MAX_FLASH_BANKS_DETECT from this board port.
This new framework will be used by the upcoming lwmon5 update as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Recent changes caused that the HMI10 board now is included in the
boards built by MAKEALL, which revealed that compilation for this
board has been broken for a long time:
ps2ser.c: In function 'ps2ser_init':
ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function)
ps2ser.c:155: error: (Each undeclared identifier is reported only once
ps2ser.c:155: error: for each function it appears in.)
ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function)
ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function)
ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function)
ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function)
ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function)
ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function)
ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_putc':
ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_getc_hw':
ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_interrupt':
ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function)
The board is orphaned, and AFAICT has reached EOL.
Drop support for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
!! This breaks support for all arm boards !!
To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"
!! This define will be removed soon, so convert your
board to use relocation support
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
fixup_cmdtable() did all work for fixing up the cmdtable,
if CONFIG_RELOC_FIXUP_WORKS is not defined.
CONFIG_RELOC_FIXUP_WORKS is missing for i386! I talked
with Graeme Russ, and he will fix this soon.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Motivation:
* Old environment code used a pessimizing implementation:
- variable lookup used linear search => slow
- changed/added variables were added at the end, i. e. most
frequently used variables had the slowest access times => slow
- each setenv() would calculate the CRC32 checksum over the whole
environment block => slow
* "redundant" envrionment was locked down to two copies
* No easy way to implement features like "reset to factory defaults",
or to select one out of several pre-defined (previously saved) sets
of environment settings ("profiles")
* No easy way to import or export environment settings
======================================================================
API Changes:
- Variable names starting with '#' are no longer allowed
I didn't find any such variable names being used; it is highly
recommended to follow standard conventions and start variable names
with an alphanumeric character
- "printenv" will now print a backslash at the end of all but the last
lines of a multi-line variable value.
Multi-line variables have never been formally defined, allthough
there is no reason not to use them. Now we define rules how to deal
with them, allowing for import and export.
- Function forceenv() and the related code in saveenv() was removed.
At the moment this is causing build problems for the only user of
this code (schmoogie - which has no entry in MAINTAINERS); may be
fixed later by implementing the "env set -f" feature.
Inconsistencies:
- "printenv" will '\\'-escape the '\n' in multi-line variables, while
"printenv var" will not do that.
======================================================================
Advantages:
- "printenv" output much better readable (sorted)
- faster!
- extendable (additional variable properties can be added)
- new, powerful features like "factory reset" or easy switching
between several different environment settings ("profiles")
Disadvantages:
- Image size grows by typically 5...7 KiB (might shrink a bit again on
systems with redundant environment with a following patch series)
======================================================================
Implemented:
- env command with subcommands:
- env print [arg ...]
same as "printenv": print environment
- env set [-f] name [arg ...]
same as "setenv": set (and delete) environment variables
["-f" - force setting even for read-only variables - not
implemented yet.]
- end delete [-f] name
not implemented yet
["-f" - force delete even for read-only variables]
- env save
same as "saveenv": save environment
- env export [-t | -b | -c] addr [size]
export internal representation (hash table) in formats usable for
persistent storage or processing:
-t: export as text format; if size is given, data will be
padded with '\0' bytes; if not, one terminating '\0'
will be added (which is included in the "filesize"
setting so you can for exmple copy this to flash and
keep the termination).
-b: export as binary format (name=value pairs separated by
'\0', list end marked by double "\0\0")
-c: export as checksum protected environment format as
used for example by "saveenv" command
addr: memory address where environment gets stored
size: size of output buffer
With "-c" and size is NOT given, then the export command will
format the data as currently used for the persistent storage,
i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
prepend a valid CRC32 checksum and, in case of resundant
environment, a "current" redundancy flag. If size is given, this
value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
checksum and redundancy flag will be inserted.
With "-b" and "-t", always only the real data (including a
terminating '\0' byte) will be written; here the optional size
argument will be used to make sure not to overflow the user
provided buffer; the command will abort if the size is not
sufficient. Any remainign space will be '\0' padded.
On successful return, the variable "filesize" will be set.
Note that filesize includes the trailing/terminating '\0'
byte(s).
Usage szenario: create a text snapshot/backup of the current
settings:
=> env export -t 100000
=> era ${backup_addr} +${filesize}
=> cp.b 100000 ${backup_addr} ${filesize}
Re-import this snapshot, deleting all other settings:
=> env import -d -t ${backup_addr}
- env import [-d] [-t | -b | -c] addr [size]
import external format (text or binary) into hash table,
optionally deleting existing values:
-d: delete existing environment before importing;
otherwise overwrite / append to existion definitions
-t: assume text format; either "size" must be given or the
text data must be '\0' terminated
-b: assume binary format ('\0' separated, "\0\0" terminated)
-c: assume checksum protected environment format
addr: memory address to read from
size: length of input data; if missing, proper '\0'
termination is mandatory
- env default -f
reset default environment: drop all environment settings and load
default environment
- env ask name [message] [size]
same as "askenv": ask for environment variable
- env edit name
same as "editenv": edit environment variable
- env run
same as "run": run commands in an environment variable
======================================================================
TODO:
- drop default env as implemented now; provide a text file based
initialization instead (eventually using several text files to
incrementally build it from common blocks) and a tool to convert it
into a binary blob / object file.
- It would be nice if we could add wildcard support for environment
variables; this is needed for variable name auto-completion,
but it would also be nice to be able to say "printenv ip*" or
"printenv *addr*"
- Some boards don't link any more due to the grown code size:
DU405, canyonlands, sequoia, socrates.
=> cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Stefan Roese <sr@denx.de>,
Heiko Schocher <hs@denx.de>
- Dropping forceenv() causes build problems on schmoogie
=> cc: Sergey Kubushyn <ksi@koi8.net>
- Build tested on PPC and ARM only; runtime tested with NOR and NAND
flash only => needs testing!!
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Cc: Stefan Roese <sr@denx.de>,
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
So far, getenv() would work before relocation is most cases, even
though it was not intended to be used that way. When switching to a
hash table based implementation, this would break a number of boards.
For convenience, we make getenv() check if it's running before
relocation and, if so, use getenv_f() internally.
Note that this is limited to simple cases, as we use a small static
buffer (32 bytes) in the global data for this purpose.
For this reason, it is also not a good idea to convert all current
uses of getenv_f() into getenv() - some of the existing use cases need
to be able to deal with longer variable values, so getenv_f() is still
needed and recommended for use before relocation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This (undocumented) concept was only in use for the MVSMR and
davinci_schmoogie Sergey Kubushyn <ksi@koi8.net> boards.
Drop it for now. If really needed, it should be reimplemented
later in the context of the new environment command set.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
This patch is to save environment data to mmc card.
It uses interfaces defined in generic mmc.
Signed-off-by: Terry Lv <r65388@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
fdt_parent_offset() is an expensive operation, so we'd like to reduce
unnecessary calls to it.
Further, the practice of iterating up to the root if address/size cells
aren't found was apparently done for Linux for compatibility with certain
buggy Open Firmware implementations, and U-Boot inherited the code. The
compliant behavior is to treat a missing #address-cells as 2, and a missing
#size-cells as 1 -- never looking anywhere but the immediate parent of the
node of interest.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, if there is an error probing the NAND chip and the env is based
in NAND, the readenv() function will use a NULL function pointer and thus
jump to address 0.
Here I just check for a non-zero value of blocksize as that shouldn't be
zero when a valid device is found, but perhaps there is a better way for
someone familiar with the NAND internals to suggest.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The "usb help" doesn't format the output correctly:
=> help usb
usb - USB sub-system
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices
usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'usb write addr blk# cnt - write `cnt'
blocks starting at block `blk#' from memory address `addr'
=>
With fix below applied, the output is correct:
=> help usb
usb - USB sub-system
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices
usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'
usb write addr blk# cnt - write `cnt' blocks starting at block `blk#'
from memory address `addr'
=>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
For code that uses miiphy_{read,write}, every call invokes a full look up
of the mii list. There is already a "current_mii" cache that is used by
some code, but have the miiphy_{read,write} function use it as well. This
does increase the code size slightly, but I think it's worth it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rather than have every func re-implement the list walking code, do it one
local function. This shrinks the resulting object code a little while
making the source much more manageable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Original bug description from Feng (fdt_resize() bug caused "WARNING:
could not set linux, initrd-start FDT_ERR_NOSPACE."):
What I got is an error: "WARNING: could not set linux,initrd-start
FDT_ERR_NOSPACE." after loading Device Tree blob. This in turn caused
linux to miss init part.
After some digging, I found out the reason for this error, it is caused
by fdt_resize().
FDT blob got resized after filling in all board specific information of
PowerPC. (in boot_body_linux()). It reduced blob size with only extra
space for two fdt_reserve_entry, one for fdt itself, and one for initrd.
Then it's aligned to a 0x1000 page boundary. However, later in
fdt_initrd(), it could add two more properties, initrd-start AND
initrd-end, each one needs at least two fdt_reserve_entry sizes done by
_fdt_add_property() (name and value). Thus, the two fdt_reserve_entry
extra space is not sufficient.
So for some specific fdt size which is just under the page boundary
after resizing, this will cause an error of FDT_ERR_NOSPACE in
fdt_initrd() when setting those two properties, and failed to pass
initrd information to linux.
My fix is in fdt_resize(), leave at least 4 fdt_reserve_entry for
initrd. So instead of 2*sizeof(struct fdt_reserve_entry) for
actual_totalsize, use 5*sizeof(struc fdt_reserve_entry).
Stefan: I got this same error on katmai, when trying to boot with
initrd (run flash_self). This patch fixes this issue.
Signed-off-by: Feng Wang <fwang02@harris.com>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Most of the files have U_BOOT_CMD on a separate line,
but a few didn't and had the first line on the same line
as U_BOOT_CMD.
This changes these files by adding a line break and a tab
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
removed the command name from the help message as it is already printed.
for cmd_mmc also rewrote the message a little bit
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
If a flash is unable to be detected, and then someone calls flash_protect
on it (like the common code does in flash_init), the flash_protect logic
will dereference a NULL pointer.
Since flash_protect already does sanity checking on the info structs, add
a NULL pointer check in there.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix error handling in getenv_f() when the user provided buffer is too
short to hold the variable name; make sure to truncate and
NUL-terminate without overwriting the buffer limits.
Signed-off-by: Wolfgang Denk <wd@denx.de>
No need to output spaces 1 char at a time in a loop when the printf code
can do the same thing with the right format string. This shrinks things
and gives a nice speed up when killing off lines more than a byte or two
as printf will send out the buffer in one big chunk.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Platforms with flat device tree support can use a bootmap to relocate
the fdt_blob. This is not a must. That's why the relocation function
boot_relocate_fdt() should be use only if CONFIG_OF_LIBFDT was defined
together with CONFIG_SYS_BOOTMAPSZ (see common/cmd_bootm.c).
On MicroBlaze platforms there is no need to use a bootmap to relocate
a fdt blob. So we need a more precise focus on the compilation and usage
of boot_relocate_fdt().
In general it is valid to exclude the function boot_relocate_fdt() if
the bootmap size CONFIG_SYS_BOOTMAPSZ is not defined.
Signed-off-by: Stephan Linz <linz@li-pro.net>
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
If the user sets bootm_low and does not set bootm_size, u-boot will
report the memory node in the flat device tree incorrectly. Instead
of reporting the remaining size of memory, it will report the total
available memory which is incorrect.
Specifically this fixes the situation when booting a relocatable
kernel and the memory is reported as an offset and size in the
device tree, and the size needs to be adjusted accordingly.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function. This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).
Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.
To avoid confusion, rename into getenv_f() [as "running from flash"]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Avoid warning:
cmd_bootm.c: In function 'bootm_load_os':
cmd_bootm.c:394: warning: passing argument 2 of
'lzmaBuffToBuffDecompress' from incompatible pointer type
For 32 bit systems, this change shouldn't make a difference to code size
since sizeof(size_t) and sizeof(unsigned int) are equal. But it does fix
the warning.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If we are creating reference (handles) to nodes in a device tree we need
to first create a new phandle in node and this needs a new phandle
value. So we search through the whole dtb to find the max phandle value
and return the next greater value for a new phandle allocation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The dots printed by common/usb_storage.c as progress meter corrupt the
output for example of "fatls usb" commands like this:
=> fatls usb 0
. <<==== here
29 file.001
29 file.002
29 file.003
29 file.004
29 file.005
29 file.006
29 file.007
29 file.008
29 file.009
29 file.010
29 file.011
29 file.012
29 file.013
29 file.014
29 file.015
29 file.016
. <<==== here
29 file.017
29 file.018
29 file.019
...
Turn the progress output into a debug message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
The device type was left uninitialized which caused later tests
against DEV_TYPE_UNKNOWN to fail. In the result, "usb part" would
attempt to print information about non-existent devices like this:
=> usb part
print_part of 0
Partition Map for USB device 0 -- Partition Type: DOS
Partition Start Sector Num Sectors Type
1 0 2031616 f8
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
=>
By initializing the type as DEV_TYPE_UNKNOWN we avoid all the
"Unknown partition table" messages.
[Note: the "print_part of ?" messages is left over debug code that
will be removed in another patch.]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Given a compatible string and physical address try and find a node that
matches. This is useful when we want to find a specific device node to
update (for example if we have multiple PCI nodes we can use the
physical address to distinguish them when trying to update the device
tree).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This code is extracted out of the Linux Kernel code from
arch/powerpc/kernel/prom_parse.c.
We maintain some of the same structure to support multiple bus types even
though we only have one in the current code. In the future we might want
to translate across a PCI bus and thus it will be easier to add that
functionality back in.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The board maintainer states:
The GTH board is obsolete and has not been manufactured for
several years.
To my knowledge, no recent U-Boot build has been tested on that
card.
So drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>
The new command dumps the TLBCAM, the LAWs, and the BR/OR regs.
Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change if (ok) {
bunch of stuff
} else {
error
}
to
if (error) {
get out
}
proceed with bunch of stuff
Plus a few whitespace cleanups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is a re-submission of the patch by Harald Welte
<laforge@openmoko.org> with minor modifications for rebase and changes
as suggested by Scott Wood <scottwood@freescale.com> [1] [2].
This patch enables the environment partition to have a run-time dynamic
location (offset) in the NAND flash. The reason for this is simply that
all NAND flashes have factory-default bad blocks, and a fixed compile
time offset would mean that sometimes the environment partition would
live inside factory bad blocks. Since the number of factory default
blocks can be quite high (easily 1.3MBytes in current standard
components), it is not economic to keep that many spare blocks inside
the environment partition.
With this patch and CONFIG_ENV_OFFSET_OOB enabled, the location of the
environment partition is stored in the out-of-band (OOB) data of the
first block in flash. Since the first block is where most systems boot
from, the vendors guarantee that the first block is not a factory
default block.
This patch introduces the 'nand env.oob' command, which can be called
from the u-boot command line. 'nand env.oob get' reads the address of
the environment partition from the OOB data, 'nand env.oob set
{offset,partition-name}' allows the setting of the marker by specifying
a numeric offset or a partition name.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/43916
[2] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/79195
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Harald Welte <laforge@gnumonks.org>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of defining the flags sevaral times in different source files
(which is error prone), move them to a central place in a header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Change the return type of the *printf() functions to the standard
"int"; no changes are needed but returning the already available
length count.
This will save a few additional strlen() calls later...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Remove some INFERNO related #ifdef's from common environment code by
fixing the board configuration settings (add CONFIG_ENV_SECT_SIZE).
While we are at it, fix comment which incorrectly talks about 4 KB
environment size, while it's actually 0x4000 = 16 KiB.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rolf Offermanns <rof@sysgo.de>
This patch adds redundant environment for environment in SPI flash.
I took env_flash.c as an example and slightly modified it. Apart
from adapting things to SF, I also slightly changed the decision
logic to use area 2 as a default in case the flags are wrong because
not having a default path worried me.
I did not add a section for CONFIG_ENV_IS_IN_SPI_FLASH in environment.h
because I did not understand if this is desired and/or needed.
So to use the feature, one has to set CONFIG_ENV_OFFSET_REDUND _and_
CONFIG_SYS_REDUNDAND_ENVIRONMENT.
I checked it by powering off my board several times during flash
erase or write, because I do not know if there are other stress
test scenarios.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
AVR32 case was missing in cmd_bdinfo, resulting in compiler warning
(bd->bi_baudrate declared unsigned int at AVR32, but printf used %d)
At the same time slightly reordered #if #elif #endif to make ARM one
of the cases and not an extra case surrounding all others
Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
Tested-by: Andreas Biemann <biessmann@corscience.de>
For the following hwconfig string:
key1:subkey1=value1,subkey2=value2;key2:value3
The subkey2 cannot be extracted correctly. The parsing code looks
for comma as a stopch, but there may be two kind of stop characters:
a comma and a semicolon.
Currently the code would return "value2;key2:value3", while just
"value2" is the correct answer.
This patch fixes the issue by making the code aware of multiple
stop characters.
For old U-Boots, the issue can be workarounded by placing a comma
before a semicolon, i.e.:
hwconfig=key1:subkey1=value1,subkey2=value2,;key2:value3
Reported-by: York Sun <yorksun@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
The console_buffer size is declared in common/main.c as
-- char console_buffer[CONFIG_SYS_CBSIZE + 1];
so this extern definition is wrong.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add sec3.1 h/w geometry for fdt node fixups.
Also, technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPD has minor change from Rev 1.2 to 1.3. This patch enables Rev 1.3.
The difference has ben examined and the code is compatible.
Speed bins is not verified on hardware for CL7 at this moment.
This patch also enables SPD Rev 1.x where x is up to "F". According to SPD
spec, the lower nibble is optionally used to determine which additinal bytes
or attribute bits have been defined. Software can safely use defaults. However,
the upper nibble should always be checked.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the auto completion (with TAB) of the environment variable name
after the editenv command.
Signed-off-by: Ralf Trbenbach <ralf.truebenbach@men.de>
On the fly also fixed the following things:
- write help talked about a parameter oob, but that one was not used, so
removed it from the help message.
- the test command also allowed a force subcommand but didn't use it.
eliminated the code.
- do_onenand made static
- do_onenand contained
int blocksize;
...
mtd = &onenand_mtd;
this = mtd->priv;
blocksize = (1 << this->erase_shift);
As blocksize was not used the last two statements were unneeded so
removed them.
The first statement (mtd = ....) assigns to a global. Not sure if it
is needed, and since I could not test this, left the line for now
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The "mtdparts add" command wrote through a NULL pointer - on many
systems this went unnoticed (PowerPC has writable RAM there, some ARM
systems have ROM where a write has no effect), but on arm1136
(i.MX31) it crashed the system.
Add appropriate checks.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Extend mpc512x serial driver to support multiple PSC ports.
Subsequent patches for PDM360NG board support make use of this
functionality by defining CONFIG_SERIAL_MULTI in the board config
file. Additionally the used PSC devices are specified by defining
e.g. CONFIG_SYS_PSC1, CONFIG_SYS_PSC4 and CONFIG_SYS_PSC6.
Support for PSC devices other than 1, 3, 4 and 6 is not added
by this patch because these aren't used currently. In the future
it can be easily added using DECLARE_PSC_SERIAL_FUNCTIONS(N) and
INIT_PSC_SERIAL_STRUCTURE(N) macros in cpu/mpc512x/serial.c.
Additionally you have to add code for registering added
devices in serial_initialize() in common/serial.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
* add WATCHDOG_RESET to !tstc() loops
* prevents watchdog timeout, while waiting for input,
if CONFIG_BOOT_RETRY_TIME or CONFIG_SHOW_ACTIVITY defined
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
gcc 3.4.6 previously reported the following error on many MIPS boards
which utilize UBI:
cmd_ubi.c:193: warning: 'vol' might be used uninitialized in this function
The current code is structured such that 'vol' will never be used when
it is NULL anyway, but gcc isn't smart enough to figure this out.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
While debugging one ill behaving USB device I found two bugs in USB
storage probe.
usb_stor_get_info() returns -1 (error), 0 (skip) or 1 (ok). First part
of this patch fixes error case.
Second part fixes usb_inquiry()'s retry counter handling. Original code
had retry = -1 on error case, not retry = 0 as checked in the next line.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Here's another USB storage patch. Currently U-Boot handles storage
devices #0 - #4 as valid devices, even if there is none connected. This
patch fixes usb_stor_get_dev() to check detected device count instead
of MAX-define.
This is very important for ill behaving devices. usb_dev_desc[] can be
partially initialized if device probe fails.
After fixing get_dev() it was easy to fix "usb part" etc commands.
Previously it outputed "Unknown partition table" five times, now it's
"no USB devices available".
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Add a helper function that given an alias will delete both the node
the alias points to and the alias itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Booting a "Multi-File Image" including a linux kernel, ramdisk and
fdt, generated with
mkimage -A ppc \
-O linux \
-T multi \
-C gzip \
-a 00000000 \
-e 00000000 \
-n "kernel-2.6+initrd+dtb" \
-d "vmlinux.bin.gz:ramdisk_image.gz:board.dtb" \
multi.bin
actually fails, because ramdisk start and end addresses
didn;t get initialized. This patch fixes this issue.
Tested on the KUP4K board.
Signed-off-by: Heiko Schocher <hs@denx.de>
The code to parse alen appeared 6 times in the function.
Factored this out in a small helper function
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
This fixes the following warnings when running MAKEALL for coldfire :
cmd_bdinfo.c:354: warning: 'print_eth' defined but not used
Signed-off-by: Philippe De Muyter <phdm at macqel.be>
Support for 16bpp was supposed to be in the code but was not working.
This makes it work and has been tested in the nhk8815 board.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
When issuing a nand scrub command, the entered character is not displayed
this may be confusing. This patch makes the input character being
displayed if it is a 'y' so that an user knows he is about to scrub his
nand.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Allow overwriting defined partitions in the device tree blob
using partition info defined in the 'mtdparts' environment
variable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Match history buffer size to console buffer size. History buffer size
was hard coded to 256, artificially limiting the command buffer size.
The history buffer now tracks CONFIG_SYS_CBSIZE.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of
maximum length will overwrite part of the history buffer, causing the
board to die. Expand the console_buffer and hist_lines buffer by one
character each to hold the missing NULL char.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
This patch add functionality to use memory addresses in expressions.
This increases the power of expressions substantially
It adheres to the standard convemtions: memory addresses can be given
in the format *address (e.g. *1000)
Rationale for this change is that it allows masking off bits from a
byte that is obtained by reading data from e.g. i2c.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Fix warning: control reaches end of non-void function
Signed-off-by: Wolfgang Denk <wd@denx.de>
according to some of the comments the subaddress length is 1 or 2, but we are being
prepared for the case it becomes 3. However the code also accepted 4.
This repairs this by changing the constand 4 to 3.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.
Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
